Velux Windows in Guisborough

Velux installers offer the Velux Active home kit. This provides an automated system to enhance your indoor living. With its sensor-based ventilation apparatus, the Velux active home kit’s smart sensors repeatedly monitor your home’s temperature, humidity and CO2 levels for its optimum healthy living standards.

Sensor-based ventilation
Velux Active tracks temperature, humidity and CO2-levels, and ventilates to keep your indoor climate nice and healthy.

Automatic heat protection
Velux Active automatically protects your home from excessive heat by closing your Velux Integra blinds, awnings and shutters on hot days.

Set personal preferences
Want to swap your alarm clock for a sunrise or air out while you’re at work? Customise your indoor climate with Velux Active.

Voice-control and smart speaker integration come standard with VELUX ACTIVE with NETATMO, enabling you to draw the shades or open the windows just by asking.

While it sounds like it could be difficult to plasterboard around a Velux window, it needn’t be. As long as you have the right tools and materials, you should be able to plasterboard around your roof window easily and make good ready to be skimmed. When you or a tradesperson has fitted your Velux window into your roof, you’ll probably need to plasterboard over it to create a good ceiling. To do this, you’ll need:

• Plasterboard sheets – make sure you measure your room so you know how much you’ll need
• Screws to secure the board in place
• Drill
• Hammer
• Straight edge and pen knife to score the board before trimming
• Fine toothed saw the cut the plasterboard

When you’re ready to plasterboard around your roof window, make sure you’ve cleared enough space to work in. Then you can begin by cutting your plasterboard to size using your straight edge and pen knife to score, then your saw to get a clean cut. A common way of plasterboarding around your Velux window is to use the groove on the window frame to hold one edge of the board, then screw the other edge to the battens on the ceiling. People often use drywall screws these days as they have a better grip of the plasterboard as they drive through. You’ll need to use a drill to screw these in. However, you could use plasterboard nails, which are galvanised to stop rusting. When you’ve done this, you can then skim the walls or ask a plasterer to do it for you. Plastering, while it looks easy, is a tricky skill so it’s always best to ask a professional to do it.

Fitting a Velux window into a slate roof is very similar to the way you’d install it in other roof types. All roof windows, whether a Velux-branded one or not, will come with detailed instructions for you to follow if you want to have a go at fitting it yourself. But here are some brief instructions to give you an idea of what’s involved in installing a Velux window into a slate roof:

1. After you’ve removed the Velux window from its packaging, remove the sash (the part that opens) from the frame, according to the manufacturer’s instructions.
2. Next, you need to prepare the opening for the window. You can often cut through the felt, remove one of the battens from under a slate, then slide all the slate tiles into the roof space. You should then make the cut 40-60mm wider than the window, cutting away roof timbers then replacing them with more around the opening to strengthen it.
3. The roof window’s bottom brackets need to be installed on one of the existing battens for the slate roof. One of the slate courses should line up 105mm below the top edge of the batten you use.
4. Then, measure from the top edge of the batten upwards to the height of the window plus 45mm. This is where the top installation batten should be installed, with an overhang of 100mm on each side.
5. Remove the course of slates below the window, trim any excess felt and fold it over the surrounding timber. This helps with waterproofing.
6. Add the insulation collar according to the Velux window manufacturer’s instructions.
7. Place the frame in the opening, adding the brackets according to the instructions. You’ll find that lots of roof windows have pre-drilled holes to make it easy for you.
8. Replace the sash and line up the hinges. Take a look at the opening at the bottom between the sash and the frame – it should be even along the entire width. Remove the sash again to fix the upper brackets according to instructions.
9. Add the underfelt collar for your roof window as instructed by the manufacturer, then replace any slates at the bottom. You might need to cut them to size.
10. Next, add the flashing according to the instructions, along with any parts that are not yet attached, including the hood section and top flashing piece.
11. Replace all the slates around the window, allowing 60-100mm of space between the course of slates above the window and the top of the window to allow for rainwater drainage. Then replace the sash into the frame again.
12. Add the vapour barrier on the inside of the window using the screws provided, then tape it to the existing vapour barrier to prevent moisture from reaching your roof structure.

And that’s it! If you think that sounds a bit complicated, ask a roofer or window installer to fit your roof window into a slate roof for you. You’ll get a better finish and you can be sure that you won’t get any leaks from a botched installation.

Velux windows are a great way to add lots of light to your loft space. Velux is actually the name of a brand of roof window – not to be confused with roof lights, which are usually installed on flat roofs, or skylights, which are normally used to add natural light into a room without being able to open it. Roof windows open like regular windows and are fitted within your roof. But how much are Velux windows? Whether you choose a Velux window or another brand of roof window, they’re not cheap. Since they require special installation, including cutting roof timbers and replacing them to keep the structure strong enough, they take longer to install than a normal double glazed window. It can take up to a day to install a large Velux window, and it could set you back anywhere between £1,600 and £2,000. If you only need a small roof window in an area like a bathroom, you can expect to pay up to £1,300 for it to be fitted. Usually, there won’t be any need for scaffolding or towers because Velux windows are designed to be installed from the inside of your home. However, it’s worth setting aside an additional £500 in your budget in case unexpected problems occur and an installer needs to get on your roof to finish fitting the window. All of these prices are based on a standard roof window without any additional features. If you want to be able to control your windows with an electric switch or remote, this could set you back as much as an additional £400. For extra-low energy glass, you can expect to pay up to £200 more.