Wall Tiling in Wirral

How To Take Tiles Off A Wall

The bonding agent or adhesive usually incorporated to hold a tile against the wall are always very strong or else you’ll find your tiles peeling off. As a result, to have them removed is not the easiest of tasks and bashing them with a hammer, will only have them broken leaving you with the task of having to scrape off the pieces. A better and much easier approach to removing tiles from a wall will be to pry them off one after the other. So how do you go about this? Let’s have a look!

lSafety First, Then Remove The First Tile

• Wear a protective eye goggle and gloves.

• Break up the grout around a tile located atthe wall’s centre using a putty knife and hammer.

• Place the putty knife under the the tile and gently it with the hammer.

lRemove The Remaining Tiles

• By tapping and prying using the tools - hammer and putty knife, wipe off all the tiles in the vertical row.

• Once done, continue to detaching the tiles in the adjacent rows until you’re able to open a wallboard section that’s around 12 inches wide and does not obstruct a stud.

• Use a keyhole blade to poke it through the wallboard.

• With the help of a reciprocating saw, cut out the wallboard’s section.

lCut The Fasteners

• Using a metal-cutting blade, cut te wallboard-holding fasteners. Make sure the fasteners holding the wallboard to the top and bottom plates of the wall are both detached.

lRemove All Wallboard Sections

• Using a similar approach, gently remove the other sections of the wallboard.

• Once completed, you can easily sweep the tiles’ broken pieces.

• Finally, vaccum the grout dust to ensure the work is neatly done.

If you lack a proper training or experience, taking off your tiles from a wall is best left to a skilled professional for the best results and to prevent potential damages which can lead to additional costs.

How To Remove Tile From Wall

Have you stumbled on some stylish new tiles you wish to install in your home, be it bathroom, kitchen or living room? Or perhaps you just feel your old tiles have outstayed their welcome and need a to install a more modern and appealing wall tile. The first step before installation of the new tiles will be to remove the old ones which can be done by following these simple steps below:

lSafety

• To remove wall tiles, you’d have to chip them away and that implies shards of porcelain, ceramic or glass flying around. Hence, your safety should be a top priority.

• Use safety goggles and protective gloves to protect both your eyes and hands.

lCover Up

• With several sharp objects flying everywhere, all objects in the room are far from safe.

• Use a cardboard or old sheet to protect the room and valuable objects from damage.

lAssemble The Tools

• For wall tiles removal, you need just two tools - a hammer and a chisel that’s a bit thin.

• In the event whereby a chisel is not available, you can make use of a flat headed and large screwdriver.

lGet To Work

• Feel for a loose tile to start with and if successful, chip it out with a chisel.

• If you can’t find a loose tile, then break one by sticking the centre of a tile with a chisel and hit it hard with a hammer.

lRemove All Tiles

• Once you’ve been able to chip away or break the first tile, you can easily get access to other tiles.

lClean Up

• Try to get as much dried adhesive off the wall as you can by gently tapping it with the chisel and hammer so as not to damage the wall.

• Once done, put away the cardboard and dust sheet which should have collected much debris.

• Use a brush and dust pan to clean out the loose pieces (if any).

Wall tiles removal can be a very dangerous process which should be left to a professional especially if you lack a proper training or experience. This is not only to prevent anybody being hurt, but also to avoid any possible damages to the wall or any valuable object which can result in additional cost on repair or replacement.

How To Tile An Uneven Wall

Do you know it’s almost impossible to find a wall in any home that’s fully flat and vertical? Just like floors, walls also have areas of imperfection or where they’re a bit uneven. When it comes to tiling, these are the problematic areas in which you must work around and identify how to solve to achieve a perfect finish. If not, you may as well just have the tiles sticking out and making room for moisture to creep in affecting the longevity of your project.

There a variety of options to tackle an uneven wall surface and one of the best is plastering. To make sure the surface of your wall is even, a great step would be to plaster it. Plastering of a wall can be a very simple task, however, if you lack proper training or experience, you might want to consider getting a skilled professional to handle the project for you. Making sure the surface of your wall is even is a crucial step in the tile installation process and can be quite tricky on your first trial.

Uneven wall is usually as a result of two major factors - sagging of the wall over time and the wall’s surface is not completely flat. To solve this, you’d have to detach the boards. Then, attach a new board and re-skim the walls to create a new flat and even surface you can work on. For small imperfections and dips, simply use an adhesive cement to fill in the gaps in the plaster. This approach is perfect for holes and ding with a depth that’s not more than half a centimetre. When the cement is totally dry, you can sand it to achieve a flat finish. Happy Tiling!

How To Tile A Kitchen Wall

Tiling a kitchen wall can seem like an easy task until you get started. Errors made will forever be evident for everyone to see unless you’re prepared to spend some extra bucks. When done right, it can actually be a very satisfying project, but don’t even think about rushing into it. If you lack a proper training or experience, it’s advisable to leave the task to a skilled professional for the best results and to avoid extra costs. This guide is meant to give you a detailed insight into the process and help you avoid possible errors.

lPreparation

• Ensure you have the required amount of tiles, adhesive and grout.

• Take the tiles measurement and calculate in square metres.

• Determine the number of tiles to be used and add about 10% to the total number to cover for possible wastage.

• Check to surface to make sure its clean and dry.

lMark Out The Area To Be Tiled

• Mark out the width of the tiles with spacers using a baton of timber.

• Position a tile against the bottom-most point and draw a line.

• Put a baton along this line and follow this by a vertical line at the wall’s end.

lInstall The Tiles On The Kitchen Walls

• Apply an even layer of adhesive with a wall trowel on the kitchen’s wall surface.

• Place the first tile on the adhesive and apply small pressure, do this for the remaining tiles with similar pressure to ensure its levelled.

• Make use of tile spacers to get a uniform space in between.

• Leave the adhesive to harden before applying the grout.

lGrouting

• Remove the tile space and clear out excess adhesive

• Prepare the grout

• Make use of a grout float to apply the mixture into the joints.

• Let the grout dry up a bit before washing the surface off with a sponge and water.