Wall Tiling in Malpas

How To Tile A Bathroom Wall With Large Tiles

It is crucial to make the walls of your bathroom waterproof, and a great way to do this is by installing tiles on them. And to make it more effective, less time consuming and a lot easier, you can make use of the large tiles in your shower. So how do you have them installed? With this brief guide, you’ll learn everything you need to know about the bathroom wall large tiles installation. Let’s have a look!

lGet The Appropriate Substrate

• Clean the surface on which the large tiles will be placed

• Make use of levelling spacers to ensure the large wall tiles are even.

• Get a cement-made backer board to install the tiles

• You made require a large format wall adhesive for the installation, if the large wall tiles are different

lSet The Layout

• You may need a dry layout for the tiles installation (installation without mortar or other bonding agents).

• Start with the first wall opposite the bathroom’s entrance

• Once completed, you can continue with the remaining parts of the bathroom wall.

• Place the first tile at the centre.

• Place the subsequent tiles on each side of the previous ones to have a more balanced installation.

There are three varying materials that can be utilized in installing heavy wall tiles. These includes thin set mortar, epoxy and mastic. However, you should always make use of epoxy for large format tile layout. To do this, simply place the tiles at your desired angle and gently twist them to hold firmly in place. Continue with this process till you have successfully covered the entire bathroom wall with the large tiles. Once done, leave the bathroom wall to dry.

It is advised that you hire the professional services of a tile installation company in order to get the best outcome especially if you lack the necessary experience, tools and knowledge to carry out the project. This will save you some time, effort and money.

How To Tile An Uneven Wall

Do you know it’s almost impossible to find a wall in any home that’s fully flat and vertical? Just like floors, walls also have areas of imperfection or where they’re a bit uneven. When it comes to tiling, these are the problematic areas in which you must work around and identify how to solve to achieve a perfect finish. If not, you may as well just have the tiles sticking out and making room for moisture to creep in affecting the longevity of your project.

There a variety of options to tackle an uneven wall surface and one of the best is plastering. To make sure the surface of your wall is even, a great step would be to plaster it. Plastering of a wall can be a very simple task, however, if you lack proper training or experience, you might want to consider getting a skilled professional to handle the project for you. Making sure the surface of your wall is even is a crucial step in the tile installation process and can be quite tricky on your first trial.

Uneven wall is usually as a result of two major factors - sagging of the wall over time and the wall’s surface is not completely flat. To solve this, you’d have to detach the boards. Then, attach a new board and re-skim the walls to create a new flat and even surface you can work on. For small imperfections and dips, simply use an adhesive cement to fill in the gaps in the plaster. This approach is perfect for holes and ding with a depth that’s not more than half a centimetre. When the cement is totally dry, you can sand it to achieve a flat finish. Happy Tiling!

How To Tile A Kitchen Wall

Tiling a kitchen wall can seem like an easy task until you get started. Errors made will forever be evident for everyone to see unless you’re prepared to spend some extra bucks. When done right, it can actually be a very satisfying project, but don’t even think about rushing into it. If you lack a proper training or experience, it’s advisable to leave the task to a skilled professional for the best results and to avoid extra costs. This guide is meant to give you a detailed insight into the process and help you avoid possible errors.

lPreparation

• Ensure you have the required amount of tiles, adhesive and grout.

• Take the tiles measurement and calculate in square metres.

• Determine the number of tiles to be used and add about 10% to the total number to cover for possible wastage.

• Check to surface to make sure its clean and dry.

lMark Out The Area To Be Tiled

• Mark out the width of the tiles with spacers using a baton of timber.

• Position a tile against the bottom-most point and draw a line.

• Put a baton along this line and follow this by a vertical line at the wall’s end.

lInstall The Tiles On The Kitchen Walls

• Apply an even layer of adhesive with a wall trowel on the kitchen’s wall surface.

• Place the first tile on the adhesive and apply small pressure, do this for the remaining tiles with similar pressure to ensure its levelled.

• Make use of tile spacers to get a uniform space in between.

• Leave the adhesive to harden before applying the grout.

lGrouting

• Remove the tile space and clear out excess adhesive

• Prepare the grout

• Make use of a grout float to apply the mixture into the joints.

• Let the grout dry up a bit before washing the surface off with a sponge and water.

How To Tile A Wall

If you’re not an expert floor installer who would take wall tile installation as merely being a vertical floor, you are advised to be very cautious when tackling the project. The installation of wall tiles follow some set of rules which you’d better not break if you really wish to protect your investment. And worst of all, a wall tile done wrong is a lifetime penalty of having to look at it. So how can you get it right? Well, probably by reaching out to a wall tile installation professional for a good quality solution that’ll save you time, money and effort. However, we’ve put together this guide to help give you an insight of how it works and also to help you avoid some unnecessary expenses. Let’s have a look!

lHang a batten board

• Start your rows of tiles or bottom-most course with a batten board which works to prevent spillage of tiles.

• Position the batten board at 3/4 of the tiles’ height. Ensure not to start at the floor.

lForm A Pyramid Shape With The Tiles

• If you’ve reached the bottom row of tile, then arrange the tile in a pyramid shape. To achieve this, you’d have to install the tiles one through four as instructed. Each following row will be draped over the pyramid.

lExamine The Floor For Level & Walls For Plumb

• If your floor level or plumb is off by a maximum of a half-inch over the course of 8 feet, add extra baseboards and trim to cover up the problem.

lThe Least Size Of Tiles To Be Used Is Half-Wide

• Ensure that no “silvers (tiles that are lower than half the width of the tile in question) are incorporated in the project.