Wall Tiling in Rugeley

How To Lay Wall Tiles

Laying of wall tiles is a task that should be done with great caution, especially if you’re working on a tight budget. It is guided by its own unique set of rules which you do not dare to break if you wish to get it right the first time, and also to avoid incurring some additional costs. If you do not have a proper training or experience, laying of wall tiles is better left to a skilled professional for the best possible outcome. However, this guide will walk you through the various steps in the process to help improve your knowledge. Let’s get started!

lPrepare The Wall Surface

• Make sure the surface is clean, dry and smooth

• In wet areas, wall tiles should be fitted over a backer board

• If it’s a painted wall, ensure to sand the surface before installation.

lCreate The Layout

• Locate the centre of the wall

• Create an intersecting vertical and horizontal layout lines using a level

• Ensure to include spaces for grout joints when creating the layout.

lApply The Adhesive

• For wet areas, makes use of thin-set adhesive that’s cement-based.

• For dry areas, you can use pre-mixed mastic adhesive

• Follow the manufacturer’s instruction to prepare the adhesive

• Using a notched trowel, apply the adhesive (hold the trowel at about 45 degrees angle)

• Ensure not to cover the layout lines with the adhesive

lInstall The Tiles

• Follow the layout lines to install the wall tiles

• Place the full tiles firmly on the adhesive and twist slight and gently to make them fit.

• Use tile spacers to ensure constant gaps for grout joints.

lCut The Tiles

• After installation of the full tiles, there’ll most likely be a need to cut some tiles to fit.

• Cut the tiles with a wet saw or manual tile cutter

lGrout The Tile

• Ensure the adhesive is well dried and remove the tile spacers.

• Prepare the grout as instructed by the manufacturer.

• Use a rubber gloat to apply the grout.

• Remove the excess grout from the tile surfaces

• Wipe the tiles and joints gently using a grout sponge and clean water.

How To Tile A Bathroom Wall With Large Tiles

It is crucial to make the walls of your bathroom waterproof, and a great way to do this is by installing tiles on them. And to make it more effective, less time consuming and a lot easier, you can make use of the large tiles in your shower. So how do you have them installed? With this brief guide, you’ll learn everything you need to know about the bathroom wall large tiles installation. Let’s have a look!

lGet The Appropriate Substrate

• Clean the surface on which the large tiles will be placed

• Make use of levelling spacers to ensure the large wall tiles are even.

• Get a cement-made backer board to install the tiles

• You made require a large format wall adhesive for the installation, if the large wall tiles are different

lSet The Layout

• You may need a dry layout for the tiles installation (installation without mortar or other bonding agents).

• Start with the first wall opposite the bathroom’s entrance

• Once completed, you can continue with the remaining parts of the bathroom wall.

• Place the first tile at the centre.

• Place the subsequent tiles on each side of the previous ones to have a more balanced installation.

There are three varying materials that can be utilized in installing heavy wall tiles. These includes thin set mortar, epoxy and mastic. However, you should always make use of epoxy for large format tile layout. To do this, simply place the tiles at your desired angle and gently twist them to hold firmly in place. Continue with this process till you have successfully covered the entire bathroom wall with the large tiles. Once done, leave the bathroom wall to dry.

It is advised that you hire the professional services of a tile installation company in order to get the best outcome especially if you lack the necessary experience, tools and knowledge to carry out the project. This will save you some time, effort and money.

How To Tile A Kitchen Wall

Tiling a kitchen wall can seem like an easy task until you get started. Errors made will forever be evident for everyone to see unless you’re prepared to spend some extra bucks. When done right, it can actually be a very satisfying project, but don’t even think about rushing into it. If you lack a proper training or experience, it’s advisable to leave the task to a skilled professional for the best results and to avoid extra costs. This guide is meant to give you a detailed insight into the process and help you avoid possible errors.

lPreparation

• Ensure you have the required amount of tiles, adhesive and grout.

• Take the tiles measurement and calculate in square metres.

• Determine the number of tiles to be used and add about 10% to the total number to cover for possible wastage.

• Check to surface to make sure its clean and dry.

lMark Out The Area To Be Tiled

• Mark out the width of the tiles with spacers using a baton of timber.

• Position a tile against the bottom-most point and draw a line.

• Put a baton along this line and follow this by a vertical line at the wall’s end.

lInstall The Tiles On The Kitchen Walls

• Apply an even layer of adhesive with a wall trowel on the kitchen’s wall surface.

• Place the first tile on the adhesive and apply small pressure, do this for the remaining tiles with similar pressure to ensure its levelled.

• Make use of tile spacers to get a uniform space in between.

• Leave the adhesive to harden before applying the grout.

lGrouting

• Remove the tile space and clear out excess adhesive

• Prepare the grout

• Make use of a grout float to apply the mixture into the joints.

• Let the grout dry up a bit before washing the surface off with a sponge and water.

How To Remove Tile From Wall

Have you stumbled on some stylish new tiles you wish to install in your home, be it bathroom, kitchen or living room? Or perhaps you just feel your old tiles have outstayed their welcome and need a to install a more modern and appealing wall tile. The first step before installation of the new tiles will be to remove the old ones which can be done by following these simple steps below:

lSafety

• To remove wall tiles, you’d have to chip them away and that implies shards of porcelain, ceramic or glass flying around. Hence, your safety should be a top priority.

• Use safety goggles and protective gloves to protect both your eyes and hands.

lCover Up

• With several sharp objects flying everywhere, all objects in the room are far from safe.

• Use a cardboard or old sheet to protect the room and valuable objects from damage.

lAssemble The Tools

• For wall tiles removal, you need just two tools - a hammer and a chisel that’s a bit thin.

• In the event whereby a chisel is not available, you can make use of a flat headed and large screwdriver.

lGet To Work

• Feel for a loose tile to start with and if successful, chip it out with a chisel.

• If you can’t find a loose tile, then break one by sticking the centre of a tile with a chisel and hit it hard with a hammer.

lRemove All Tiles

• Once you’ve been able to chip away or break the first tile, you can easily get access to other tiles.

lClean Up

• Try to get as much dried adhesive off the wall as you can by gently tapping it with the chisel and hammer so as not to damage the wall.

• Once done, put away the cardboard and dust sheet which should have collected much debris.

• Use a brush and dust pan to clean out the loose pieces (if any).

Wall tiles removal can be a very dangerous process which should be left to a professional especially if you lack a proper training or experience. This is not only to prevent anybody being hurt, but also to avoid any possible damages to the wall or any valuable object which can result in additional cost on repair or replacement.