Wall Tiling in Denny

How To Tile A Bathroom Wall

Tiling your bathroom walls will not only increase the visual appeal of your space, but also provide an additional layer which helps protect against potential moisture damage, moist growth and also makes the bathroom a lot easier to clean up. So if you’re are looking to tile your bathroom, it’s recommended to get in touch with a skilled professional to ensure you get the best results. However, this guide will provide you with a good insight on how to get through the process smoothly and avoid costly errors. Let’s take a look!

lPrepare The Wall’s Surface

• Make sure that the surface is clean, smooth and dry.

• If there are any dips or holes, ensure to have them patched or sanded.

• Measure the area to be tiled and shape the backer board to fit, if a new wall surface is necessary.

• Cover the new surface area with adhesive to attach the back board to the surface.

lMix The Mortar

• Firstly determine the tile layout and make a layout tool

• Install the datum

• Follow the instructions of the adhesive package as the type you’re to use depends on the wall type.

• Create a consistent and smooth paste by mixing the adhesive with water.

lInstall The Tiles

• Using a notched trowel, spread the mortar.

• Put a thin layer at the back of each tile and press it against the surface.

• Create ridges using the notched side of the trowel.

• Clear out any excess adhesive on the tile’s surface as you continue.

• Put the spacers at the joints

• Remove the datum planks when ready to install the outer edge tiles.

lApply The Grout

• Put the grout over te tiles with a grout float

• Clean out excess grout with a damp sponge

• Seal the tiles once the grout is dried

How To Remove Tile Adhesive From Wall

Do you feel your tile design choices are outdated and want to replace it with a more stylish one? Or perhaps you’re just struggling to remove the old tile adhesive from your wall. Putting on a new wallpaper or repainting your wall might be a cup of tea, but retiling is surely a different experience altogether. After detaching every single piece of tile from the wall, you’ll still have the strongly glued adhesive to battle with. If not done properly, you may as well damage the wall which will trigger a new additional cost for repair. We’d recommend you get a professional helping hand for the best results if you’re without a proper training or experience. However, this guide will teach you everything you need to know about the process. Let’s get started!

Materials Required

• Steamer

• Protective sheets

• 4-inch scraper

• Clean cloth

• Protective gear - face mask, eye goggles, gloves.

Tile Adhesive Removal Process

• Cover The Floor

Ensure that the floor is well covered to collect the residues falling off from the wall with some protective sheets.

• Heat Up The Adhesive

Using the wallpaper steamer, heat up the adhesive to make it a bit loose and softer. Do this by slowly moving the steamer around and ensure not to stay on one spot for too long.

• Scrape Off The Mortar

When you can tell the adhesive is properly softened, use the 4 inch scraper to wipe it off the wall. Do this until all the adhesive has been completely removed.

• Clear Out The Fallen Residue

Clean up any mortar that has fallen on the floor.

After the tile adhesive removal, your wall may need to be skimmed depending on its state. This is to put the surface in a good and flat condition before installing the new tiles. The wall may also need to be re-plastered if the adhesive is extremely strong.

How To Lay Wall Tiles

Laying of wall tiles is a task that should be done with great caution, especially if you’re working on a tight budget. It is guided by its own unique set of rules which you do not dare to break if you wish to get it right the first time, and also to avoid incurring some additional costs. If you do not have a proper training or experience, laying of wall tiles is better left to a skilled professional for the best possible outcome. However, this guide will walk you through the various steps in the process to help improve your knowledge. Let’s get started!

lPrepare The Wall Surface

• Make sure the surface is clean, dry and smooth

• In wet areas, wall tiles should be fitted over a backer board

• If it’s a painted wall, ensure to sand the surface before installation.

lCreate The Layout

• Locate the centre of the wall

• Create an intersecting vertical and horizontal layout lines using a level

• Ensure to include spaces for grout joints when creating the layout.

lApply The Adhesive

• For wet areas, makes use of thin-set adhesive that’s cement-based.

• For dry areas, you can use pre-mixed mastic adhesive

• Follow the manufacturer’s instruction to prepare the adhesive

• Using a notched trowel, apply the adhesive (hold the trowel at about 45 degrees angle)

• Ensure not to cover the layout lines with the adhesive

lInstall The Tiles

• Follow the layout lines to install the wall tiles

• Place the full tiles firmly on the adhesive and twist slight and gently to make them fit.

• Use tile spacers to ensure constant gaps for grout joints.

lCut The Tiles

• After installation of the full tiles, there’ll most likely be a need to cut some tiles to fit.

• Cut the tiles with a wet saw or manual tile cutter

lGrout The Tile

• Ensure the adhesive is well dried and remove the tile spacers.

• Prepare the grout as instructed by the manufacturer.

• Use a rubber gloat to apply the grout.

• Remove the excess grout from the tile surfaces

• Wipe the tiles and joints gently using a grout sponge and clean water.

How To Tile An Uneven Wall

Do you know it’s almost impossible to find a wall in any home that’s fully flat and vertical? Just like floors, walls also have areas of imperfection or where they’re a bit uneven. When it comes to tiling, these are the problematic areas in which you must work around and identify how to solve to achieve a perfect finish. If not, you may as well just have the tiles sticking out and making room for moisture to creep in affecting the longevity of your project.

There a variety of options to tackle an uneven wall surface and one of the best is plastering. To make sure the surface of your wall is even, a great step would be to plaster it. Plastering of a wall can be a very simple task, however, if you lack proper training or experience, you might want to consider getting a skilled professional to handle the project for you. Making sure the surface of your wall is even is a crucial step in the tile installation process and can be quite tricky on your first trial.

Uneven wall is usually as a result of two major factors - sagging of the wall over time and the wall’s surface is not completely flat. To solve this, you’d have to detach the boards. Then, attach a new board and re-skim the walls to create a new flat and even surface you can work on. For small imperfections and dips, simply use an adhesive cement to fill in the gaps in the plaster. This approach is perfect for holes and ding with a depth that’s not more than half a centimetre. When the cement is totally dry, you can sand it to achieve a flat finish. Happy Tiling!