Painting / Decorating in Cheadle

How To Prep Walls For Painting

This is exactly the part of a wall painting job that can make or mar the whole project. To ensure that your paint project doesn’t end up being disastrous, the most important place to start is from room preparation which includes cleaning, sanding as well as priming the walls before painting. Not every wall will require to go through all the preparation steps as all walls are unique and some are in better conditions than others. However, it’s advisable to thoroughly inspect the surfaces before you proceed to painting and take the necessary actions where required.

This is a very simple DIY job that should be completed in little time, however it’s also perhaps the most important step of the entire painting project. Hence, if you lack the confidence to pull this off, then we’d recommend employing a painting expert who can guarantee the best results for help. In this guide, we’ll should you how you can prepare your wall for painting.

✓ Cleaning. There is no single best way to properly clean a wall, but most walls will be just fine with a sponge and warm water. For walls that have been stained with oil or grime such as kitchen walls, you can apply grease cutting detergent and water mixture to wash and follow up with warm water to clean the residues and a damp cloth wiping to finish it off. Then leave to dry off properly.

✓ Remove mildrew. Wipe out mildrew using a sponge and solution that’s three to four parts water to one part bleach. Apply this solution and scrub the affected surface with a soft brush.

✓ Sanding. This step is only meant for walls with rough spots on its surface. Dull the uneven spots with a sandpaper, wipe away the dust and leave to dry. Use a fine grit sandpaper to sand the surfaces and let it dry properly.

✓ Priming. Prime the wall to get the most out of your paint. They work to disguise imperfections and create a smooth surface on which you can work on.

How Much For A Painter To Paint A Room?

If you’re looking to have your room painted, it’s only normal to get an idea of how much it’s going to cost so you can set a budget and start planning. As you would have expected, the cost of having a room painted is dependent on a wide array of influencing factors such as the size of your room, the type of paint to be used, your location and many more. As a result, providing a single and accurate answer to this question is almost impossible.

Generally, a regular 4 metres by 3 metres room will take just a couple of days to be fully painted including both the coving and woodwork. Outside London, most painters and decorators would charge within the range of £150 to £200 per day meaning that you’ll have a total labour cost within the range of £300 to £400. What’s more? You’d also have to consider the price of the paint to be used which is usually around £50. If you add all the costs together you’ll get an average cost of about £400 to £500.

Unfortunately, paint does not last an eternity. Therefore, there’ll come a time where you’d have to consider painting your room all over again. It may seem unwise to employ the services of a professional painter and decorator especially if you’re on a budget. However, in truth, calling in a professional can go a long way to save you time, stress and money. In other words, even if you’re worried about the cost, a professional painter is still your best bet in the long run as they know exactly what to do to ensure you derive maximum benefits from your painting project.

There are lots of paints that are suitable for different areas of your property. In general, gloss and eggshell paints should be used in high traffic areas, whereas matte paints are suitable for lower traffic areas. Professional painters and decorators can give you advice on the most suitable types of paints.

How To Paint A Room

Painting is a joyful task and it’s quite obvious why it’s one of the most popular DIY projects. Whether you’re painting as an experienced DIYer or as a newbie, this step by step guide will put you in the right direction. However, if you lack the confidence to carry out this task, then we’d recommend you get in touch with a seasoned professional who can guarantee the best results for help. This way, you get to save some time and additional money that would have resulted from possible costly errors.

So just before you head right into the task, there’s the need to determine the type of pain finish you would love to use which is to choose a colour. Now let’s get started!

• Prepare the room

✓ Remove all objects as much as you can from the room and cover the remaining furniture or objects with a sheet.

✓ Fill all holes on the surface to make for an even finish.

✓ Wash the wall with the help of a damp sponge. A sugar soap or diluted washing up liquid will work just fine.

✓ Tape the edges of objects you do not wish to paint like light switches, plug sockets and the likes.

• This step can be skipped if painting on an existing paint, but it’ll advisable to dilute small quantity of your selected paint to patch prime the holes that you’ve filled. If you have a large number of holes that was filled, then priming them would be smart.

• Mix or stir the paint thoroughly in a paint kettle to ensure an even and perfect mix.

• Now you’re ready to start painting! Start from the edges to form like a frame to work within with your roller. Once done, leave for about 4 to 6 hours to dry.

• For the second coat, simply repeat the above step to complete your painting project.