Question 1

Where should I put my garden shed?

Accepted Answer

Try to put your shed in open space, away from trees, bushes and other buildings. This will help to protect it from falling branches and sap. It will also mean that you can access all sides of the shed for repair and maintenance purposes. Make sure you take a look at garden shed planning rules before you pick a final spot for your shed.

Question 2

Can I insulate my shed?

Accepted Answer

Yes, it is possible to insulate a shed. You might want to do this if you’re planning on working in it during the winter. A professional will be able to help you find an insulated shed or advise you on how to insulate a shed that you already have. Always seek professional advise first before attempting to do this yourself!

Question 3

How to build a shed base?

Accepted Answer

You need a firm, level base for your shed to ensure that it stays structurally sound – without one, doors will sag, walls will lean and it won’t last you as long. But how do you build a shed base and what should you make it from? Timber shed bases A timber shed base is made from pressure-treated timber and has metal spikes that you hammer into the ground to keep it in place. You can often buy them with your shed installation kit, but they also come separately, often in 6x4 or 7x5 sizes. To build a timber shed base, you’ll drill holes then fit screws in the timber until the entire frame is built. Remember to check it’s square, then fix L-shaped feet to the inside of the frame. If you’re putting your shed on a hard surface like concrete, this is all you need to do. If you’re putting the base on soft ground, hammer in spikes at each corner until they’re level with the top of the base, then secure the spikes to the base with screws. Then you can position the shed floor onto the base. How to build a plastic shed base A plastic shed base is a simple and quick way to build a shed base. You can lay it on level concrete or paving slabs, but adding sharp sand on top will help keep it more secure. They come in a kit containing plastic grids. To build your plastic base, first measure out the site and hammer a peg into each corner and tie with string or builder’s line. Make it slightly larger than the shed base to help with drainage. Then cut into the lawn and remove the turf, making sure it’s level. Lay down a membrane sheet and weigh it down if it’s windy. Then lay out the number of plastic grids you need, then remove the locking pins and clip all the grids together. Once they’re all connected, put the locking pins back in the centre of the grids. Put your shed floor on top and you’re done! Concrete or paved shed bases For a concrete base or a shed base made from paving slabs, you’ll need to dig a sub-base. For concrete bases, you’ll need to dig down 150mm so you can add 75mm of compact hardcore under 75mm of concrete. For paved shed bases, you’ll want it to be about 120mm deep for 50mm of compact hardcore and the paving slabs. How to build a shed base out of paving slabs Mix sand and cement together to make mortar or use a pre-mixed one Use a trowel to lay mortar for 1 slab at a time on the sub-base and lift a damp-sided slab onto the mortar, using a piece of timber and club hammer to tap the slab into position carefully. Continue to lay the first row of slabs Make equally-sized spacers in all the joints in the slabs to ensure they’re the same size, checking it’s level as you go along Next lay slabs along the two adjacent outer edges, filling in the central area row by row Leave the mortar to set according to the instructions or for at least 48 hours before filling in the joints with mortar or paving grout Building a shed base from concrete Create a wooden frame around your shed base area (also called formwork) to stop the concrete from spreading Mix pre-mixed concrete with water or use 1 part cement to 5 parts ballast Wet the sub-base using a watering can with a rose on the end Pour the concrete onto the framed base starting in one corner Push the blade of a shovel up and down in the edges of the concrete to get rid of air bubbles Use a rake to spread the concrete, leaving it around 18mm higher than the top of the frame. Work in sections of around 1-1.m2 Compact the concrete using a straight piece of timber that’s longer than the width of the base. Move the timber along the site, hitting it along at about half of its thickness at a time until the surface is evenly ridged Remove excess concrete and level the surface by sliding the timber back and forwards from the edge that you started. Fill in any depressions and repeat until even Run an edging trowel along the frame to round off exposed edges of the concrete and prevent chipping Cover the concrete with a plastic sheet raised on wooden supports to allow slow drying. Weigh it down with bricks Once the concrete is set, you can install your shed and remove the wooden frame with a crowbar Don’t fancy having a go at building a shed base yourself? Get a range of quotes from a professional and see how much it will cost.

Question 4

How to insulate a shed?

Accepted Answer

If you spend time in your shed, whether you use it as a summer house or an office, you’ll probably want a bit of insulation in there for when it starts to get chilly. There are different ways to insulate a shed, and some aren’t expensive at all. You just need to decide what the best way for you is. Bubble wrap If you don’t spend too much time in your shed, bubble wrap is an easy and cheap way to insulate your shed. Simply attach bubble wrap strips to the framing of the shed to create an air gap, then screw or nail a sheet of MDF over the top. Fibreglass wool Fibreglass wool is a good option if you want to insulate your shed further. Make sure you use safety equipment to protect your eyes, nose, mouth and hands when you’re handling it. Tack a breathable membrane to the inner walls of the shed, then place the fibreglass wool on top. Add a sheet of MDF or wood board, ensuring all the fibreglass is covered. Insulating shed windows and doors You'll often feel draughts through shed windows and doors, and these are easy to block up. You can use foam filler or liquid wool along the edges of the windows and gaps in the door frame. Let it dry out after you’ve applied it then cut off any excess. Insulate the floor If you’re building a new shed, you could fit some underfloor insulation to the grid of the shed base – it could help reduce up to 40% of heat lost through the shed floor. But if your shed’s already built, you can line the floor with a breathable membrane then lay a rug or piece of carpet down. The membrane underneath stops any damp or rot forming, so it’s best not to lay a rug straight down on the shed floor.

Avg. price low	Avg. price low £475
Avg. price	Avg. price £1,050
Avg. price high	Avg. price high £1,595

	Labour cost	£420
	Material cost	£150
	Waste removal	£30

Garden Sheds in Llandrindod Wells

Compare Garden Sheds Prices in Llandrindod Wells

Garden Sheds in Llandrindod Wells

Average Garden shed cost in Llandrindod Wells

Average price per Garden shed job in 2024

Garden shed installation cost in Llandrindod Wells 2024

Garden shed searches in November 2024

Garden shed Projects in Llandrindod Wells in October 2024

928

0

0

Garden shed searches in cities and towns near Llandrindod Wells October 2024

Garden shed near you

Llandrindod Wells

Looking for Garden shed in Llandrindod Wells?

Get free quotes from local carpenters

How it works

Tell us about your Garden shed project

Find up to 4 Carpenters in Llandrindod Wells

Hire with confidence

Our reviews

Average

Would highly recommend

Good easy way to find a selection of…

Love LeadsDoWork it's a big part of my …

FAQs

Other Top Projects in Llandrindod Wells

Customer Reviews

Are you a carpenter in Llandrindod Wells?