Wall Tiling in Whitstable

How To Remove Tile From Wall

Have you stumbled on some stylish new tiles you wish to install in your home, be it bathroom, kitchen or living room? Or perhaps you just feel your old tiles have outstayed their welcome and need a to install a more modern and appealing wall tile. The first step before installation of the new tiles will be to remove the old ones which can be done by following these simple steps below:

lSafety

• To remove wall tiles, you’d have to chip them away and that implies shards of porcelain, ceramic or glass flying around. Hence, your safety should be a top priority.

• Use safety goggles and protective gloves to protect both your eyes and hands.

lCover Up

• With several sharp objects flying everywhere, all objects in the room are far from safe.

• Use a cardboard or old sheet to protect the room and valuable objects from damage.

lAssemble The Tools

• For wall tiles removal, you need just two tools - a hammer and a chisel that’s a bit thin.

• In the event whereby a chisel is not available, you can make use of a flat headed and large screwdriver.

lGet To Work

• Feel for a loose tile to start with and if successful, chip it out with a chisel.

• If you can’t find a loose tile, then break one by sticking the centre of a tile with a chisel and hit it hard with a hammer.

lRemove All Tiles

• Once you’ve been able to chip away or break the first tile, you can easily get access to other tiles.

lClean Up

• Try to get as much dried adhesive off the wall as you can by gently tapping it with the chisel and hammer so as not to damage the wall.

• Once done, put away the cardboard and dust sheet which should have collected much debris.

• Use a brush and dust pan to clean out the loose pieces (if any).

Wall tiles removal can be a very dangerous process which should be left to a professional especially if you lack a proper training or experience. This is not only to prevent anybody being hurt, but also to avoid any possible damages to the wall or any valuable object which can result in additional cost on repair or replacement.

How To Tile A Bathroom Wall

Tiling your bathroom walls will not only increase the visual appeal of your space, but also provide an additional layer which helps protect against potential moisture damage, moist growth and also makes the bathroom a lot easier to clean up. So if you’re are looking to tile your bathroom, it’s recommended to get in touch with a skilled professional to ensure you get the best results. However, this guide will provide you with a good insight on how to get through the process smoothly and avoid costly errors. Let’s take a look!

lPrepare The Wall’s Surface

• Make sure that the surface is clean, smooth and dry.

• If there are any dips or holes, ensure to have them patched or sanded.

• Measure the area to be tiled and shape the backer board to fit, if a new wall surface is necessary.

• Cover the new surface area with adhesive to attach the back board to the surface.

lMix The Mortar

• Firstly determine the tile layout and make a layout tool

• Install the datum

• Follow the instructions of the adhesive package as the type you’re to use depends on the wall type.

• Create a consistent and smooth paste by mixing the adhesive with water.

lInstall The Tiles

• Using a notched trowel, spread the mortar.

• Put a thin layer at the back of each tile and press it against the surface.

• Create ridges using the notched side of the trowel.

• Clear out any excess adhesive on the tile’s surface as you continue.

• Put the spacers at the joints

• Remove the datum planks when ready to install the outer edge tiles.

lApply The Grout

• Put the grout over te tiles with a grout float

• Clean out excess grout with a damp sponge

• Seal the tiles once the grout is dried

How To Tile A Kitchen Wall

Tiling a kitchen wall can seem like an easy task until you get started. Errors made will forever be evident for everyone to see unless you’re prepared to spend some extra bucks. When done right, it can actually be a very satisfying project, but don’t even think about rushing into it. If you lack a proper training or experience, it’s advisable to leave the task to a skilled professional for the best results and to avoid extra costs. This guide is meant to give you a detailed insight into the process and help you avoid possible errors.

lPreparation

• Ensure you have the required amount of tiles, adhesive and grout.

• Take the tiles measurement and calculate in square metres.

• Determine the number of tiles to be used and add about 10% to the total number to cover for possible wastage.

• Check to surface to make sure its clean and dry.

lMark Out The Area To Be Tiled

• Mark out the width of the tiles with spacers using a baton of timber.

• Position a tile against the bottom-most point and draw a line.

• Put a baton along this line and follow this by a vertical line at the wall’s end.

lInstall The Tiles On The Kitchen Walls

• Apply an even layer of adhesive with a wall trowel on the kitchen’s wall surface.

• Place the first tile on the adhesive and apply small pressure, do this for the remaining tiles with similar pressure to ensure its levelled.

• Make use of tile spacers to get a uniform space in between.

• Leave the adhesive to harden before applying the grout.

lGrouting

• Remove the tile space and clear out excess adhesive

• Prepare the grout

• Make use of a grout float to apply the mixture into the joints.

• Let the grout dry up a bit before washing the surface off with a sponge and water.

How To Tile A Wall

If you’re not an expert floor installer who would take wall tile installation as merely being a vertical floor, you are advised to be very cautious when tackling the project. The installation of wall tiles follow some set of rules which you’d better not break if you really wish to protect your investment. And worst of all, a wall tile done wrong is a lifetime penalty of having to look at it. So how can you get it right? Well, probably by reaching out to a wall tile installation professional for a good quality solution that’ll save you time, money and effort. However, we’ve put together this guide to help give you an insight of how it works and also to help you avoid some unnecessary expenses. Let’s have a look!

lHang a batten board

• Start your rows of tiles or bottom-most course with a batten board which works to prevent spillage of tiles.

• Position the batten board at 3/4 of the tiles’ height. Ensure not to start at the floor.

lForm A Pyramid Shape With The Tiles

• If you’ve reached the bottom row of tile, then arrange the tile in a pyramid shape. To achieve this, you’d have to install the tiles one through four as instructed. Each following row will be draped over the pyramid.

lExamine The Floor For Level & Walls For Plumb

• If your floor level or plumb is off by a maximum of a half-inch over the course of 8 feet, add extra baseboards and trim to cover up the problem.

lThe Least Size Of Tiles To Be Used Is Half-Wide

• Ensure that no “silvers (tiles that are lower than half the width of the tile in question) are incorporated in the project.