Wall Tiling in Newton Stewart

How To Tile A Bathroom Wall With Large Tiles

It is crucial to make the walls of your bathroom waterproof, and a great way to do this is by installing tiles on them. And to make it more effective, less time consuming and a lot easier, you can make use of the large tiles in your shower. So how do you have them installed? With this brief guide, you’ll learn everything you need to know about the bathroom wall large tiles installation. Let’s have a look!

lGet The Appropriate Substrate

• Clean the surface on which the large tiles will be placed

• Make use of levelling spacers to ensure the large wall tiles are even.

• Get a cement-made backer board to install the tiles

• You made require a large format wall adhesive for the installation, if the large wall tiles are different

lSet The Layout

• You may need a dry layout for the tiles installation (installation without mortar or other bonding agents).

• Start with the first wall opposite the bathroom’s entrance

• Once completed, you can continue with the remaining parts of the bathroom wall.

• Place the first tile at the centre.

• Place the subsequent tiles on each side of the previous ones to have a more balanced installation.

There are three varying materials that can be utilized in installing heavy wall tiles. These includes thin set mortar, epoxy and mastic. However, you should always make use of epoxy for large format tile layout. To do this, simply place the tiles at your desired angle and gently twist them to hold firmly in place. Continue with this process till you have successfully covered the entire bathroom wall with the large tiles. Once done, leave the bathroom wall to dry.

It is advised that you hire the professional services of a tile installation company in order to get the best outcome especially if you lack the necessary experience, tools and knowledge to carry out the project. This will save you some time, effort and money.

How To Take Tiles Off A Wall

The bonding agent or adhesive usually incorporated to hold a tile against the wall are always very strong or else you’ll find your tiles peeling off. As a result, to have them removed is not the easiest of tasks and bashing them with a hammer, will only have them broken leaving you with the task of having to scrape off the pieces. A better and much easier approach to removing tiles from a wall will be to pry them off one after the other. So how do you go about this? Let’s have a look!

lSafety First, Then Remove The First Tile

• Wear a protective eye goggle and gloves.

• Break up the grout around a tile located atthe wall’s centre using a putty knife and hammer.

• Place the putty knife under the the tile and gently it with the hammer.

lRemove The Remaining Tiles

• By tapping and prying using the tools - hammer and putty knife, wipe off all the tiles in the vertical row.

• Once done, continue to detaching the tiles in the adjacent rows until you’re able to open a wallboard section that’s around 12 inches wide and does not obstruct a stud.

• Use a keyhole blade to poke it through the wallboard.

• With the help of a reciprocating saw, cut out the wallboard’s section.

lCut The Fasteners

• Using a metal-cutting blade, cut te wallboard-holding fasteners. Make sure the fasteners holding the wallboard to the top and bottom plates of the wall are both detached.

lRemove All Wallboard Sections

• Using a similar approach, gently remove the other sections of the wallboard.

• Once completed, you can easily sweep the tiles’ broken pieces.

• Finally, vaccum the grout dust to ensure the work is neatly done.

If you lack a proper training or experience, taking off your tiles from a wall is best left to a skilled professional for the best results and to prevent potential damages which can lead to additional costs.

How To Tile A Kitchen Wall

Tiling a kitchen wall can seem like an easy task until you get started. Errors made will forever be evident for everyone to see unless you’re prepared to spend some extra bucks. When done right, it can actually be a very satisfying project, but don’t even think about rushing into it. If you lack a proper training or experience, it’s advisable to leave the task to a skilled professional for the best results and to avoid extra costs. This guide is meant to give you a detailed insight into the process and help you avoid possible errors.

lPreparation

• Ensure you have the required amount of tiles, adhesive and grout.

• Take the tiles measurement and calculate in square metres.

• Determine the number of tiles to be used and add about 10% to the total number to cover for possible wastage.

• Check to surface to make sure its clean and dry.

lMark Out The Area To Be Tiled

• Mark out the width of the tiles with spacers using a baton of timber.

• Position a tile against the bottom-most point and draw a line.

• Put a baton along this line and follow this by a vertical line at the wall’s end.

lInstall The Tiles On The Kitchen Walls

• Apply an even layer of adhesive with a wall trowel on the kitchen’s wall surface.

• Place the first tile on the adhesive and apply small pressure, do this for the remaining tiles with similar pressure to ensure its levelled.

• Make use of tile spacers to get a uniform space in between.

• Leave the adhesive to harden before applying the grout.

lGrouting

• Remove the tile space and clear out excess adhesive

• Prepare the grout

• Make use of a grout float to apply the mixture into the joints.

• Let the grout dry up a bit before washing the surface off with a sponge and water.

How To Tile A Bathroom Wall

Tiling your bathroom walls will not only increase the visual appeal of your space, but also provide an additional layer which helps protect against potential moisture damage, moist growth and also makes the bathroom a lot easier to clean up. So if you’re are looking to tile your bathroom, it’s recommended to get in touch with a skilled professional to ensure you get the best results. However, this guide will provide you with a good insight on how to get through the process smoothly and avoid costly errors. Let’s take a look!

lPrepare The Wall’s Surface

• Make sure that the surface is clean, smooth and dry.

• If there are any dips or holes, ensure to have them patched or sanded.

• Measure the area to be tiled and shape the backer board to fit, if a new wall surface is necessary.

• Cover the new surface area with adhesive to attach the back board to the surface.

lMix The Mortar

• Firstly determine the tile layout and make a layout tool

• Install the datum

• Follow the instructions of the adhesive package as the type you’re to use depends on the wall type.

• Create a consistent and smooth paste by mixing the adhesive with water.

lInstall The Tiles

• Using a notched trowel, spread the mortar.

• Put a thin layer at the back of each tile and press it against the surface.

• Create ridges using the notched side of the trowel.

• Clear out any excess adhesive on the tile’s surface as you continue.

• Put the spacers at the joints

• Remove the datum planks when ready to install the outer edge tiles.

lApply The Grout

• Put the grout over te tiles with a grout float

• Clean out excess grout with a damp sponge

• Seal the tiles once the grout is dried