Roof replacement (Pitched/Tiled) in Firth Of Clyde

The task of installing a tile roof can be quite a difficult one. Such a project takes a great deal of preparation, well before the actual tile installation is done. It does not matter if you are putting new ones or replacing your old tiles, understanding the proper technique and steps become crucial.

Remove old roofing (if applicable).

This is, on its own, a major job that can take days and require special tools. It takes some time, but be prepared to do it right.

Install battens (if applicable).

Battens may be needed to hold the tiles in place if the roof is having a steep slope. Usually made of metal or wood, battens are generally 1 inch thick and run horizontally along the roof.

You can find several varieties of tiles that has a hook or a lip allowing it to hang on the available battens. Apart from this, you can find several clips in the market which help to attach the tiles on to the batten.

Determining the spacing for battens can be done easily using two tiles. To prevent interlocking, a three inch overlap is required at the minimum, and a smaller amount of overhang should be left over the eaves. Keep this in mind when you determine the locations of the battens.

After you have determined the distance between the first two battens, measure the distance and set battens using that spacing up, making sure to double-check measurements as you go along.

• Install the tiles.

• You will need to begin with one side first, and then continue to move along the length of the roof.

• Cut tiles to fit tight spots.

• Tiles have to be cut precisely to overcome any obstacle like the chimney.

• Install the ridge tiles.

After completing the broad surfaces of the roof, special ridge tiles are required to cap the top.

A roof is one of the most significant portions of any property and they’re also the single part of a structure most vulnerable to impairment from the elements. If your roof suffers substantial damage over time, maintenances and re-roofing charges can be expensive, time-consuming, and stressful which is why it is imperative to keep your roof in sound structural and aesthetic order.

If a tile has fallen off from the top of your roof – you can expect to pay around £70-£100 to replace it including a different tile fitted in its place. Replacing a hip roof will cost between £4,250 and £7,250, the cost varies if you have a single valley or a double valley on your roof. For a new gable roof, you should expect to pay around £3,250 to £5,250.

What does it cost to replace my roof?

The charge of substituting your roof for a new one will be subject to the age and condition that it’s in, but usually, the cost of a new roof on an average property is around £5,500.

Some of the key factors to keep in mind when calculating the cost of re-roofing your house include:

• size of your roof

• type and size of the materials used

• shape and style of the roof

• If structural changes are required or not

• the roofing company hired

Tiled roof repair costs

If you are trying to prevent water from leaking inside your house for one or two tiles, then you can expect to pay between £100 to £200 to fix them and seal the leaks.

Flat roof repair costs

Minor jobs such as repairing flat roofs as well as sheds and garages or mending blisters can usually cost around £300.

Roofing job Price range

Replacing six ridge tiles £135-£260

Replacing six broken or missing tiles £55-£105

Cleanout of your gutter £35-£80

Replacing one right tile on rooftop £70-£100

The cost of a full re-roofing job can amount to around £3,250 to £7,250 depending on the size of your property.

Hip roof Cost range Length of time

Semi-detached home £4,250-£4,750 3-4 days

Detached home £5,250-£5,750 4-5 days

2 valleys – semi-detached home £5,750-£6,250 5-6 days

2-valleys detached home £6,750-£7,250 6-7 days

Gable roof Cost range Length of time

Standard £3,250-£3,750 2-3 days

2-valley £4,750-£5,250 4-5 days

A roof serves as something which is so much more than just a top of a building. A roof delivers guard from the elements and precipitation, it also helps drain water from a structure, and helps to provide insulation to the structure allowing it to keep the interior of a building cool or warm, according to season.

There are several steps to building a roof

Mount the trusses.

This step requires the building’s wall frames to be completely level, square and plumb. If you are building the roof onto a building that is still a frame you must use ladders or scaffolding. Hoist the trusses onto the roof.

Install temporary braces.

You will need to install temporary braces that the trusses can rest on until the sheathing and permanent bracing are installed, this has to be done before you install the trusses. At the centre of the back wall, nail the bottom half of one two-by-six board that's 16 feet long to the top of the outside wall, making sure you fasten it to a stud.

Install the end trusses.

Install the two end trusses at the front and back of the building, making sure you affix them to the temporary bracing. The batten you take will have to be a bit longer than the distance will separate the trusses.

Install the standard trusses.

According to the instructions provided by the manufacturer, you will first need to install the first standard truss. You will also need to nail it to the batten from the first truss.

Sheath the roof.

Once your trusses permanently braced, you can begin with the sheathing of the roof. Starting from the bottom corner and moving across the bottom, the sheathing is installed lengthwise.

Install the roof cover.

Like the sheathing and underlayment procedures, the roof cover is installed lengthwise from the bottom up. The shingles should be staggered, and they should also overlap at the same time. You will need to work up to the ridge and use a ridge cap shingles to finish the ridge.

There is simply not one single answer when it comes to knowing how much would it cost to replace a commercial roof. Replacement costs is a variable which is dependent on several factors.

If you are looking to take a shot at guessing an estimate, you will first need to understand the what is need for the replacement.

YOUR COMMERCIAL ROOF IS AGEING

The first sign of replacement is definitely the age. Generally, roofs come with a warranty of twenty years. Based on your materials, the real lifespan for a commercial roof tends to be around 15 to 25 years. Depending on the maintenance and the materials, lifespan can be prolonged.

YOUR COMMERCIAL ROOF LOOKS TIRED

Compare your commercial property with other buildings in the area. If it looks pale and worn out in comparison, it is high time for replacement.

WATER DAMAGE

A sturdy roof should be able to withstand extreme weather conditions such as heavy rain or high winds. However, if a storm has caused significant damage to your roof, its structural integrity might be compromised. water damage is one of the most indicative signs for a roof replacement.

CRACKS AND HOLES IN ROOFING MATERIALS

Proper upkeep of the roofing materials is required for it to continue protecting your property. If you find any cracks or holes, bent tiles or sheets, replacing them is advisable.

SAGGING COMMERCIAL ROOF

Roof replacement is critical when your roof suffers from sagging or corrosion. Once sagging or corrosion begins, the structure becomes vulnerable to damage.

Keeping all the above factors in mind, replacing your commercial roof can range from anywhere around £10,900 to £44,000 depending on the materials you choose. Materials are available in the market from £35 to around £75 per square meter. If you chose higher or premium quality materials, price can range from £115 to £200 per square meter.