New Flat Roof in Slough

How Much Is It To Replace A Garage Roof?

The size of your garage will be the main determinant of the cost of a new garage roof. However, the present condition of your roof structure as well as the type of roof covering preferred are also huge factors. In the UK, the cost of a garage roof replacement will be within the range of £700 to £3600.

The first step a pro will take is to remove the existing roofing while also making sure that the timber structure is in a good condition. In the event whereby the timber is rotten, it will need to be replaced before the installation of a new roof. If the garage roof sheets needs a replacement, you’ll have to spend about £30 to £50 per each garage roof sheets. Individual plywood sheet has around 2.4m x 1.2m in measurement and whose price should also be included in the final cost.

The above information applies only to standard roofing for garage roofs with flat roofs being made of bitumen felt and asphalt. In recent times, this is no longer the case with several more options available. Today, EPDM and GRP fibreglass have rapidly become very popular amongst several homeowners in the country. It’s also important to note that modern roofing has greatly advanced over the years even though both EPDM garage roofs and GRP fibreglass garage roofs are way better and of more quality when compared to felt and asphalt roofs. And thanks to modern technology, modern garage roofing possesses a longer life expectancy and as result, are a lot costlier than the conventional ones.

For a medium size single garage (2.7m x 5.5m), the cost for a felt roof per square metre is between £40 to £70, while that of a fiberglass roof and an EPDM rubber roof is between £90 to £110 and £70 to £100 respectively.

If your existing roof is still in good condition but the membrane is getting old, it’s often not worth exposing the structure to the weather whilst the contractor strips off the old membranes. The contractor will leave them in place to act as a base layer for a new roofing system. As long as there are no other problems with your roof, then overlaying is a good way to replace your flat roof.If you have any more questions about flat roofing that aren’t listed here, fill out our form to ask a contractor.

Ponding is where you see pools of water appearing on your flat roof. Unless your roof is leaking or showing other signs of damage, you don’t need to replace it. When you do have your flat roof replaced, tell the contractor so they can find out the cause of the ponding.

How To Replace Flat Roof Felt

Also referred to as tar paper, roofing felt is installed underneath the roof’s shingles to help deny water access to your home. Installing the roofing felt in overlapping layers builds a water barrier in situations whereby the weather damages or blows away the shingles. Although the application of a roofing felt on a flat roof is relatively easier and safer than working on a peaked roof, it’s advisable to take enough care and precautions. If you lack proper training and experience for this task, we’d recommend you employ a reliable professional to guarantee the best results and save you from further headaches especially in cases whereby unfortunate errors are made. This step by step guide will give you a good insight into the flat roof felt replacement process.

• Take a measurement of the width and length of the roof.

• Calculate the square footage by multiplying the numbers.

• Multiply the square footage gotten by three (it’s advisable to install three layers of roofing felt to create a really strong weather barrier).

• Use a claw hammer to remove the existing roofing felt.

• Use utility knife to cut the new felt to fit the length of the roof.

• Place the first piece along the roof’s edge and use a hammer tacker to tack the felt in place with staples or galvanized nails and hammer.

• Put the staples or nails at every 6 inches along the side touching the roof’s edge as well as down the short sides.

• Repeat the same process for the second piece, laying it out beside the first row of felt.

• Cut a piece of felt to the appropriate length using a utility knife to begin the second layer of roofing felt, and cutting it in half, lengthwise.

• Apply construction adhesive along the first row using a trowel.

• Press the first piece for the second layer onto the adhesive. Repeat this process until the roof is covered with a second layer

• Apply construction adhesive over the second layer to install the third layer. Begin with a full piece of felt without cutting it in half.

• Overlap each piece by 2 inches until you’ve completely installed the third layer.