Commercial / Industrial Roofing in Houghton Le Spring

Whether you’re liable for a leaking roof in a commercial property will depend on your ownership status and any contracts. Of course, if you own a standalone commercial property, it would make it your responsibility to repair to leaking roof. But if you own an office within a building, you should check your paperwork to see whether you are responsible for some or all of a leaking roof.

If you’re a tenant in a commercial property, things get a bit more complicated. Lots of commercial leases are FRI, or Full Repairing and Insuring leases, which means that the tenant is responsible for all external and internal maintenance and insuring the building. It means that it’s vital that you read through your tenancy agreement in full before signing it and seek legal advice if you think you need it. If your lease is an FRI lease, you are liable for a leaking roof in your commercial property.

It’s important to ensure that you have a schedule of condition for the property, which will mean that you only have to restore the commercial property back to the condition that it was in when you took over. It’s also worth getting the roof inspected before you sign the lease, as if there is any damage before you sign the landlord may be responsible.

The best way to avoid having to pay for a leaking roof in a commercial property is prevention. If you are liable for repairs and maintenance, make sure you have the roof inspected regularly by a reputable company to avoid having to pay for costly repairs when disaster strikes.

There are a few reasons why commercial buildings often have flat roofs. Lots of people argue that flat roofs aren’t as attractive as pitched roofs, which is why it’s uncommon to see a residential property with an entirely flat roof. Lots of commercial buildings don’t need to look attractive, so go for flat roofs because they’re cheaper.

Flat roofs tend to be less expensive than pitched roofs, especially for large, broad commercial buildings. Some commercial buildings simply couldn’t have a pitched roof because their width would mean that the roof would have to be extremely high. Flat roofs are also cost-effective for commercial buildings because it means that air conditioning and ventilation units can go on the roof, saving space in and around the building.

Commercial buildings also often have flat roofs because they don’t need the loft space that residential properties need. If there’s no need for the space, it doesn’t make sense to spend more money on a pitched roof just to keep the attic space empty. Flat roofs also give the commercial building owner the opportunity to use the space as a smoking area for employees or give access to fire escapes to upper floors.

If you’re having a commercial property build, make sure you speak to the experts about the type of roof that is suitable for you. If you’re planning on having air conditioning or ventilation systems installed within the property, you might be best off with a flat roof – but if you need some extra storage space, a pitched roof might work best for you.

How you install commercial rubber roofing is similar to fitting it on a residential property, except that the area that’s covered is likely to be bigger. With commercial properties, you should always leave any maintenance and repair works to the professionals – whether you own or lease the property, you could invalidate any insurance if you try to install rubber roofing yourself. We’ll outline the steps roofers will take when installing rubber roofing on a commercial property.

Firstly, the installers will remove any existing coverings and clean and dry the surface thoroughly. This is vital in ensuring that the rubber will stick. They will then unwrap the EDPM rubber membrane and leave it to rest until it’s fully expanded. On a warm day this may take around half an hour.

Next, the roofers will work with half a sheet of rubber at a time and adhere it to the roof surface. They may use a water-based adhesive which they will spread onto the roof in sections, then roll the membrane onto the surface before moving onto the next section. If they’re using a bonded adhesive, they will apply it to both the roof and the rubber and leave it to dry until it’s tacky before extending the membrane.

Once the EDPM rubber is rolled out, the installers will brush the surface with a large broom to get rid of bubbles and provide a stronger bond. Then they will work of the edges, applying adhesive to roof and walls edges, sealing corners and creating watertight seals. They’ll also tidy up any excess membrane and seal all the trims.

As long as it’s installed correctly, your commercial rubber roofing should last you decades without any repairs needed. It’s always best to inspect your roof regularly to spot any damage before it becomes a bigger problem.

How long it takes to fix a roofing sheet on a commercial property will depend on the size of your roof and how difficult access is. Corrugated iron roofing sheets are much easier to fit than other roofing materials such as clay tiles or EDPM rubber, so that will work in your favour.

The size of the team of the roofing company you engage will also make a difference. If they have a lot of tradespeople working on your roof with lots of experience, it will take less time, while if there are only a couple of people it will take longer.

Another thing to bear in mind when considering how long it will take to fix a roofing sheet is the weather. If it starts to rain, the contractors will probably have to stop and wait, as the roof will be too slippery to work on.

In general, it should take between 1 and 3 days to fit roofing sheets on a commercial property. If you’re not having a full roof replacement, it may only take one day, whereas a completely new metal roof could take up to 3 days.