Kitchen Tiling in Herefordshire

If you’re not an expert floor installer who would take wall tile installation as merely being a vertical floor, you are advised to be very cautious when tackling the project. The installation of wall tiles follow some set of rules which you’d better not break if you really wish to protect your investment. And worst of all, a wall tile done wrong is a lifetime penalty of having to look at it. So how can you get it right? Well, probably by reaching out to a wall tile installation professional for a good quality solution that’ll save you time, money and effort. However, we’ve put together this guide to help give you an insight of how it works and also to help you avoid some unnecessary expenses. Let’s have a look!

1. Hang a batten board
2. Start your rows of tiles or bottom-most course with a batten board which works to prevent spillage of tiles.
3. Position the batten board at 3/4 of the tiles’ height. Ensure not to start at the floor.
4. Form A Pyramid Shape With The Tiles
5. If you’ve reached the bottom row of tile, then arrange the tile in a pyramid shape. To achieve this, you’d have to install the tiles one through four as instructed. Each following row will be draped over the pyramid.
6. Examine The Floor For Level & Walls For Plumb
7. If your floor level or plumb is off by a maximum of a half-inch over the course of 8 feet, add extra baseboards and trim to cover up the problem.
8. The Least Size Of Tiles To Be Used Is Half-Wide
9. Ensure that no “silvers (tiles that are lower than half the width of the tile in question) are incorporated in the project.

Tiling a kitchen wall can seem like an easy task until you get started. Errors made will forever be evident for everyone to see unless you’re prepared to spend some extra bucks. When done right, it can actually be a very satisfying project, but don’t even think about rushing into it. If you lack a proper training or experience, it’s advisable to leave the task to a skilled professional for the best results and to avoid extra costs. This guide is meant to give you a detailed insight into the process and help you avoid possible errors.

• Preparation

✓ Ensure you have the required amount of tiles, adhesive and grout.

✓ Take the tiles measurement and calculate in square metres.

✓ Determine the number of tiles to be used and add about 10% to the total number to cover for possible wastage.

✓ Check to surface to make sure its clean and dry.

• Mark Out The Area To Be Tiled

✓ Mark out the width of the tiles with spacers using a baton of timber.

✓ Position a tile against the bottom-most point and draw a line.

✓ Put a baton along this line and follow this by a vertical line at the wall’s end.

• Install The Tiles On The Kitchen Walls

✓ Apply an even layer of adhesive with a wall trowel on the kitchen’s wall surface.

✓ Place the first tile on the adhesive and apply small pressure, do this for the remaining tiles with similar pressure to ensure its levelled.

✓ Make use of tile spacers to get a uniform space in between.

✓ Leave the adhesive to harden before applying the grout.

• Grouting

✓ Remove the tile space and clear out excess adhesive

✓ Prepare the grout

✓ Make use of a grout float to apply the mixture into the joints.

✓ Let the grout dry up a bit before washing the surface off with a sponge and water.

When your tiles get old and starts to lose its curb appeal and deteriorate, it’s certainly time to have it removed. When it comes to old wall tiles removal, you have two options which is either you do it yourself or call in a professional – with the latter being more advisable. However, if you wish to save some money on installation and carry out the task yourself, then you’ve come to the right place!

Firstly, you have to know that the bonding agent or adhesive usually incorporated to hold a tile against the wall are always very strong or else you’ll find your tiles peeling off. As a result, to have them removed is not the easiest of tasks and bashing them with a hammer, will only have them broken leaving you with the task of having to scrape off the pieces. A better and much easier approach to removing tiles from a wall will be to pry them off one after the other. So how do you go about this? Let’s have a look!

1. Safety First, Then Remove The First Tile
   Wear a protective eye goggle and gloves.
2. Break up the grout around a tile located atthe wall’s centre using a putty knife and hammer.
3. Place the putty knife under the the tile and gently it with the hammer.
4. Remove The Remaining Tiles
   By tapping and prying using the tools - hammer and putty knife, wipe off all the tiles in the vertical row.
5. Once done, continue to detaching the tiles in the adjacent rows until you’re able to open a wallboard section that’s around 12 inches wide and does not obstruct a stud.
6. Use a keyhole blade to poke it through the wallboard.
7. With the help of a reciprocating saw, cut out the wallboard’s section.
8. Cut The Fasteners
   Using a metal-cutting blade, cut te wallboard-holding fasteners. Make sure the fasteners holding the wallboard to the top and bottom plates of the wall are both detached.
9. Remove All Wallboard Sections
   Using a similar approach, gently remove the other sections of the wallboard.
10. Once completed, you can easily sweep the tiles’ broken pieces.
11. Finally, vaccum the grout dust to ensure the work is neatly done.

If you lack a proper training or experience, taking off your tiles from a wall is best left to a skilled professional for the best results and to prevent potential damages which can lead to additional costs.

Some floor tiles are so lovely you just can’t help but wonder if it’s safe to be used on the walls as well. If you’re also thinking along the same line, you’re not alone! Several other home and property owners are busy finding answers to this particular question. Now let’s look at the possibilities.

Generally, any tile designed as a floor tile by the tile manufacturer can also be laid on the wall (vertical surfaces) as well as countertops. Due to the fact that the floors are usually subjected to greater use than the walls in terms of foot traffic, the durability required is also considerably greater. Therefore, a floor tile with Abrasion Resistance values ranging from I - V is suitable for wall installation. However, you should take note that exterior wall applications must be different from its interior counterparts and must only be incorporated on tiles that are frost resistant.

There are two other factors that must be taken into consideration before you install a floor tile on your walls which includes the weight of your tiles per m2 as well as the strength of the surface in which the tile is to be installed. If you don’t want your tiles falling off, the combined weight of the tiles with the adhesive and grout should not be more than the maximum weight required per m2 (20kg to 35kg depending on the wall substrates).

Now that you have an idea of the possibilities of installing floor tiles on walls, it must, however, be said that reverse is the case when it comes to installing walls tiles on the floor. Wall tiles are, generally, not suitable to be laid on the floor as they are mostly non-vitreous ( cannot withstand excessive impact, abrasion or thaw cycling).