House Rewiring in Wigan

The short and simple answer to this question is, no. If you’re a seasoned DIYer then you should probably know a thing or two about electrical works around your property. However, house rewiring works should only be carried out by a qualified and registered electrician for a handful of reasons. In this FAQ, we’re going to take an in depth look at a few reasons why a house rewiring project should always be tackled by a reliable professional.

• Risk. Not only do you out your own health and that of your loved ones at risk when you attempt to complete electrical rewires on your own, but you also put your property at risk. Tackling electrical works involves a great danger. These dangers can come in different forms such as electrical wires electrocution, shock as well as fire. What’s more? Items in your home also possesses higher voltages, and when it comes to electrical wiring, the higher the voltage, the more dangerous the project becomes. Another tricky task to get around is hidden junction boxes as well as connections. Since these components are out of sight, the chances of you getting shocked increases rapidly. All these risks can only be mitigated when proper procedures are followed . therefore, if you decide to do electrical work on your home, then there’s the need to obtain necessary permits for completing the work. Once completed, the work done should be inspected by a licensed electrical inspector. However, the best way to reduce the risks is by hiring the services of a licensed electrician.
• Safety. Electricians are trained to perfect their craft and comply with safety protocols. They’re also required to pass a licensing test so as to work as an electrician. The safety of your property and loved ones when it comes to your home’s electrical works can only be guaranteed when done by a qualified and registered electrician.

There is no set guidelines for rewiring your property however if your house is more than 20-30 years of ages it would certainly constantly be best to get an EICR accomplished to determine the problem of the electrical installation. If you are most likely to be accomplishing a great deal of repair works such as a brand-new kitchen/bathroom/extension this might additionally be a good time to have your house rewired as every little thing might then be done simultaneously

Modern wires is PVC covered, PVC shielded and copper is made use of for the conductors. It lasts for years. At once in the 1940s and 1950s cables were made using rubber as well as this wires was known to be harmful. Rubber protected as well as sheathed cable came to be dry and also weak, especially if it obtained very warm under hefty use, and also the threat was the dry as well as breakable rubber made use of to break away from the conductors leaving revealed live wire. This caused fires and also fatal shocks if touched. Modern PVC electrical wiring does not struggle with destruction this way so the requirement to rewire is somewhat lowered.

Unlike in houses built in the 1970s where a good majority of the houses will not need to be rewired, for houses built in the 1960s you’d probably need to rewire the entire house unless the wiring is the modern PVCu coated type. Generally, the homes built especially in the 1960s and 1970s brought about enormous changes. This is because over the years our way of living began to change and as a result, our need for electricity became even greater. In response to this, the electrical systems we incorporate needed to change in order to match the new set standards.

In the 1960s, the amperage normally used was increased to 100, which enables home and property owners to power their dishwasher, microwave as well as refrigerator all on one circuit. However, while this may be a remarkable improvement for our grand parents, this is just enough to cater for our modern day appliances. In recent times, new homes are constructed using a wide range of dedicated circuits due to the fact that each of our appliances makes use of much more electricity to function. Consequently because the 100 amp panels of the 1960s possessed restricted space for breakers, home and property owners who still had the units in their homes will inevitably require a sub panel or a new panel entirely - meaning a total rewiring of their property.

Furthermore in the 1960s, builders turned to aluminium from the previously used copper as it was a great conductor and also happens to be relatively cheap. However, after a couple of years a host of electrical fires cropped up in houses that are wired using aluminium. It was later discovered that when the switch to aluminium was made, the light switches or receptacles which were originally made for the previously used copper was overlooked. It was learned that there’s a corrosive chemical reaction that arises as a result of the two dissimilar metals when connected. Hence, the more reason why aluminium wired houses in the 1960s needs to be rewired.

If you’re thinking about adding new power sockets to your room, then you’ve come to the right place! This task can be a very tricky one especially if you don’t know how to go about it. If you don’t have the skills or experience necessary to pull this off, then we’d strongly recommend you hire the services of qualified and licensed electrician who can guarantee the best results for help. In this guide, we’re going to take you through the numerous steps you’d have to take to make sure your new power sockets is added successfully. Let’s take a look!

• All the power to the working area at the primary electrical panel should be turned off.
• Identify the cut area for individual electrical box.
• Pilot saw blade by drilling corner holes
• Drill into framing for wiring, if required
• Connect electrical wires to the electrical panel from the outlet box holes, pulling four feet through the wall.
• Attach white wires to silver screws as well as black wires to brass screws and also the ground wire.
• Incorporate electrical tape to tape around the box
• Connect the box to the wall and cover with the outlet plate
• Carry out the process for individual outlet needed
• De-energize the entire electrical panel by shutting off the house’s main breaker
• Fit an arc volt breaker by connecting white and black wire to the breaker
• Connect white wire from the new breaker directly onto the neutral bar of the electrical panel
• Finally, you can turn the main breaker back on.