Gas Appliance Installation in Aberdovey

How Much Is A Landlord Gas Certificate?

Do you know as a landlord in the UK, not only does the law requires you to conduct an annual check on all your gas appliances and chimney, but you’d also have to pay for it? Hence, giving birth to the commonly asked question, how much is a landlord gas certificate? With so many variances in CP12 certificate prices everywhere, it can be so confusing knowing the actual one you’re expected to pay. Just by surfing the internet alone you’d come across loads of ads claiming they can help you with a cheap gas safety certificate only to discover that reverse is the case when you reach out to them. Here, you’ll get to know the real amount you’re expected to pay for the annual checks on your gas appliances and chimney.

First and foremost, let’s look at what a Gas Safety Certificate really is. This is a certificate that’s given out to landlords and property management companies after a check has been carried out on all their gas appliances and chimney. This statutory check is expected to be done every 12 months to ensure the safety of all those who make ue of your rental property. Homeowners living in ther property are not required by the law to conduct annual gas safety check, but it’s highly recommended that you get in touch with a Gas Safety engineer to ensure the safety of both you and your loved ones.

As a landlord in the UK, to get all your gas appliances and chimney inspected by an approved Gas Safety engineer and obtain your Gas Safety Certificate, you’re expected to pay within a range of £55 to £65. However, you should note that this cost will increase depending on the number of gas appliances you have (about 30% increase for each additional gas appliance).

What Is A Gas Safety Certificate?

Do you wish to know what a Gas Safety Certificate is and if you need to get one?

If you’re in the UK and you own a rental property, you have a statutory obligation to obtain a Gas Safety Certificate. The law ( Gas Safety - Installation and Use, Regulations 1998) stipulates that landlords as a matter of necessity should have all their gas appliances, fittings,and property flues subjected to yearly checks in order to ensure that they’re are totally safe.

The Gas Safety Certificate can be referred to in a number of ways which includes Landlord Gas Safety Record ( LGSR) or CORGI PROFORMA 12 (CP12). The later dating back to when the official body for gas safety in the UK was CORGI. However, the official body is now known as Gas Safe, hence it’s now usually called a Gas Safety Certificate or something along that line. But regardless of whatever you choose to call it, as long as you reside in the UK, it’s crucial to know that if you need one as soon as possible. So how do know if you need a Gas Safety Certificate?

If you’re a homeowner with a property that you live in, you’re not required by the law to obtain a Gas Safety Certificate. There’s nothing like a homeowner’s gas safety certificate, however we’d recommend you subject all you gas appliances and pipework to yearly examinations to ensure they’re functioning properly and safely.

If you’re a landlord in the UK, you’re required by the law to get a Gas Safety Certificate to ensure your property is safe for your tenants. You must reach out to an approved Gas Safe engineer who’ll carry out annual checks on your appliances to ensure that they’re totally safe.

How To Install A Gas Cooktop In An Island

Are you thinking about installing a gas cooktop in your kitchen island? If yes, then you must know that there are clearance requirements that must be met (before you proceed) between the cut out and the countertop’s edge. Basically, there are incremental requirements for island installation due to the fact that it does not make an assumption that the product is going to be fitted against a rear wall that acts to protect the back of the unit. As a result, while doing an island install we must put the safety of the product into consideration much more that we do a standard install. What’s more? This island clearance requirement develops from a third-party agency and is a standard with all brands. So how do you install a gas cooktop in an island having the aforementioned requirements in mind?

• Use a foil tape to line the inside edges of the cut out. The function of this is to prevent heat damage as well as countertop’s discolouration. Put the cooktop top on a secured surface.

• Identify the pipe coming out of the cooktop’s side or bottom and brush onto the threads of the manifold entrance.

• Pass the pressure regulator onto the entrance of the manifold and make use of a wrench to tighten it.

• Brush the pipe joint compound onto one of the flare union adaptor’s threads and pass it into the regulator’s open end. Make it slightly tight with a full turn of the wrench.

• Connect the flare union adaptor’s open end with the flexible appliance connector hose, upon brushing on pipe joint compound.

• Put foam tape on the cooktop underside’s edges, if your cooktop comes with a glass burner plate.

• Turn the cooktop to set it into the cutout.

• Apply pipe-joint compound onto the flare union adaptor left and secure it firmly into the gas shutout valve.

• Connect the flexible hose connector’s free end with the flare union adaptor.

How Much Does It Cost To Move A Gas Meter?

When your gas meter is not in the right location while completing your renovation works or extending your property, it can be a worrying experience.

As a homeowner, you’re not allowed by the law to move your gas meter by yourself - it’s a very dangerous task that’s too risky to undertake just by watching a Youtube video or reading a blog post. Moving of a gas meter can and should only be carried out by a qualified and licensed gas supplier. And this, ultimately, gives rise to the question - how much does it cost to move a gas meter? Before we provide an answer for that, let’s look at what moving of a gas meter entails.

First and foremost, moving of a gas meter typically involves switching off the gas source to your home or property. The pipeline about 2 metres away from your property would be cut into for safety reasons and diverted into another position. Furthermore, you can as well apply that your meter should be re-fitted and re-linked to the inner copper pipeline, but that’s if the inner copper pipeline happens to be within two metres of the new location of your gas meter.

The time involved in the completion of a gas meter re-location project depends largely on the complexity of the job as each project is unique. Typically, the standard timescale from preparation to the final stage of moving a gas meter will take between 4 to 8 weeks. Finally, how much will it cost to relocate your gas meter?

As there are no government funds to subsidize gas meter relocation costs, this can be a very expensive work to carry out. Generally, the price to move a gas meter of about 5m will start within the range of £640 to £670.