Floor Tiles (Supplied and Fitted) in Gloucestershire

How To Lay Tiles On Concrete

Installation of tiles on concrete sub-floors can be done with relative ease under adequate guidance. Here is what you have to do.

lPrepare The Concrete Subfloor

• Ensure the concrete is dry, clean and must be at least 6 weeks old.

• If there are dips and humps, level the concrete using a levelling compound.

lSet Out

• Working from the centre outwards, take a measurement of the floor (both length and width) and draw a cross at the centre.

• Lay out the tiles from the cross with a space of 3mm between each tiles. This will allow for movement stresses within the floor and later to be filled with grout upon installation of the tiles and adhesive dried.

lCut The Tiles

• Due to the particularly had nature of some floor tiles such as natural stone and porceclain, high quality tools are usually required to produce a clean cut through the tiles. With the help of an electric wet cutter alongside a slide cutter and nippers, your job would be made a lot easier.

• For a better result during intricate cuts, make use of a cardboard template.

lFix The Tiles

• The tiles should be fixed using a cement-based adhesive.

• Ensure to refer to the packaging or product data for the mixing ratios information.

• Stir the mixture till its lump-free

lApply The Mixture

• Spread the mixture onto the concrete sub-floor to create parallel ribs with the help of a floor trowel.

• Push the tiles into the parallel ribs.

• Clear out any excess adhesive from the tiles surface with a damp sponge.

• Do not walk on the tiles for at least 2 hours.

lGrout

• Once the adhesive is dried, wipe out any dust, adhesive or dirt from the tiles’ gaps.

• Mix about 4 to 5 parts of grout powder with 1 part of water and ix together.

• Apply the mixed grout diagonally across the tiles using a soft rubber grout float.

• Wipe out excess grout from the tiles surface and allow the tiles to dry.

• Stubborn residues can be cleaned using any washing up detergent with warm water within 24 hours after grouting.

How To Tile A Kitchen Floor

Tiling your kitchen floor can seem a daunting task at first glance, but is a skill that can be mastered after a couple of practices. With this simple guide, you will find it easier to satisfy your kitchen floor tiling needs.

lPrepare The Subfloor

• Ensure the subfloor is very secure to support both the tile and the people working across it.

• If necessary, you can strengthen the kitchen floor with the help of a vinyl, heavy felt or any other good backer board.

• After successfully securing the floor, proceed to clear out all dust and dirt.

lMix The Mortar

• Mix a thinset mortar be referring to the instructions on the package. ( Mix only the quantity you can apply within 30 minutes).

• Once the mixture looks similar to the thickness of mayonnaise, allow it to rest for about 10 minutes before application.

lApply The Mortar

• Apply a thin layer of mortar

• Do not cover extensive areas as the mortar can become very dry.

• Spread the mortar with a trowel in curved patterns to make it flat on the floor.

lSet The Tile

• Set down the tile slowly, apply a little pressure until its holds firmly to the surface. ( Apply a consistent amount of pressure throughout to ensure equal heights for all the tiles)

• Continue with the process until all full tiles are well positioned

lCut The Tiles

• Once all the full tile pieces are in place, start cutting to cover the edges requiring smaller tile pieces.

• Take accurate measurements of the outer edges needing smaller tile pieces.

• Cut the tile pieces to fit the measurement taken with the help of a wet saw or hand tile cutter.

lGrouting

• Remove all spacers and mortar residues and lay the grout

• Apply the grout along the tiles’ seams with a grout float

• Clean out excess grout with a damp sponge after leaving it to dry for about 30 minutes

• Once the grout is fully dried, apply the sealer (the drying process normally takes within 3 to 4 days).

For the best results, it’s advisable to contact a tiling professional for help when it comes to kitchen floor tiling especially if you have no training or prior experience. This way, you can get the best quality and also avoid the regrettable mistakes and extra costs that’s very common with newbies.

How To Tile A Bathroom Floor

Are you looking to tile your bathroom floor very soon? Well, we’ve got you covered! Tiling is not the easiest skill to acquire and definitely not one you’d not want to try out on your bathroom with some practices. For the best results and to get it right the first time, we’d recommend you hire the services of a reliable professional especially if you’re inexperienced or without a bathroom tiling training. Hopefully, this quick step-by-step guide will put you in the right direction.

Bathroom Floor Tiling Procedures

lMake Sure You Have A Levelled Subfloor

• Your subfloor’s stability is crucial for the success of your tile laying.

• Once done, then you can start planning how to level the floor.

• Identify the highest point of your floor and place a really long level to determine the dip and hump spots.

• Fill in the identified low spots with mortar.

lCut The Tiles

• Using a wet saw with a diamond blade and pump, cut through the tiles to get the appropriate shape.

lChoose The Appropriate Adhesive

• To best adhesive is probably the one written on the label and suggested by the manufacturer.

• If uncertain, you can make use of a modified mortar

lPrepare The Area

• Using the prepared mixture of your mortar, prime the surface by spreading it on the floor with the trowel’s flat side.

• Once done, you can add more mortar with the ridges of the trowel.

lSpace The Tiles

• Tile spacement depends largely on the surrounding walls. Straight walls equal straight tiles, if not your judge would be required to ensure a great outcome.

• If the wall is straight, make a space of about an eighth of an inch. The bigger spacing, the higher the possibility for the grout to become visibly discoloured.

lUse The Right Grout

• With sanded and unsanded grouts having a variety of colours, choosing the ideal grout can a tricky affair.

• The size of the spaces play a huge role in determining the best choice.

• Use a sanded grout if the spacing is an eighth of an inch or more. However if less, make use of the unsanded grout.

Do you wish to have your residential or commercial space tiled? With a plethora of benefits that comes with a tiled floor, it’s little surprise more and more home and property owners are going for this special flooring type. Not only are they able to improve the curb appeal of any property, but they’re also resistant to moisture helping to increase the durability of the house – be it wall or floor tiles.

Tiling a floor is not the simplest of tasks and should be done with utmost care and attention to details. If you lack the confidence to pull this off, we’d recommend you hire a reputable professional who can guarantee the best outcome the first time.  In this guide, you’ll find processes involved in floor tiling to help put you in the right direction.

Floor Tiles Installation Procedures

1. Floor Preparation
   The first step is to prepare the floor by moving all objects like mortar, adhesives and more. Use concrete patching compound to fill ill low spots and cracks, until the floor is levelled.
2. Ensure the floor is dry and clean.
3. Pattern Layout
   Take the measurement of each wall’s length while also taking into account the room’s diagonals.To help place the tiles in an orderly manner, make use of a chalk to mark down lines on the levelled surface in question and ensure it’s parallel to the walls.
4. Adhesive Preparation
   Mix the appropriate amount of water with the adhesive (bonding agent). The mixture should be toothpaste-like thick to ensure the durability of the tiles.
5. Tiles Placement
   Depending on the tile’s size, evenly spread the mortar on the floor using a notched trowel. Lay the first tile on the bonding agent (adhesive or mortar) and apply a gentle and little pressure on the tile.
   
   Repeat the technique for other tiles using plastic spacers to ensure the edges and corners are properly aligned.
6. Tiles Cutting
   Cut the tiles (if necessary) with the help of a wet saw or scoring cutter featuring a diamond-tripped blade.
7. Grout Application
   Filling of the tiles’ gap is done using the grout. It can be applied to the joints with a rubber float. After application, allow the grout to set up for some minutes. Use sponge and a bucket of water to clear out any adhesive leftover.
8. Grout Sealing
   Use a foam brush or applicator bottle for the sealants’ application. Clean out excess sealer within 10 minutes.