Boiler Grants in Islington

Ad hoc visits from your engineer to fix small issues with your heating system may actually seem cheaper and a lot more affordable, however when a boiler is ripe enough for a change these small issues are always never ending. Over some period of time, these small issues will inevitably get worse and the idea of “mend and make do will be an absolutely false economy. The best course of action in this sort of event is to find a replacement boiler to install as soon as possible. In this article, we’re going to give you some hints that’ll show you when your boiler needs to be replaced. Now let’s take a look!

✓ Insufficient hot water. Here, you’ll have to check the size of your hot water cylinder. It’s crucial to make sure that your boiler is rightly sized to power your heating as well as hot water circuit in line with your demands. You should always seek the advice of a heating expert who can recommend whether to fix or replace the boiler.

✓ Strange noises. It’s normal for components of the boiler to become worn or damaged over time. Replacing the particular component that’s causing the knocking or rattling may seem cost effective at first but more often than not, the noises usually signal a bigger issue which is likely to build up over time. Hence, it’ll be a lot more logical to replace the boiler itself.

✓ Regular repair of your boiler. It’s essential to have your heating system serviced by a Gas Safe engineer on an annual basis. However, when you have to call them more often than once a year for your yearly maintenance, it may be a wise decision to consider getting a replacement.

✓ Other events whereby you may need a new boiler includes when you can’t get the right temperature in your room, when the radiators don’t heat up as they should, when your boiler leaks and if your boiler still has a pilot light.

Re-pressurising your boiler means that you allow more water to enter system via the filling loop. It can be easy to re-pressurise your boiler yourself. Always check your manual, but there are some simple steps you can take to restore pressure to your boiler:

• Switch off your boiler and let it cool completely

• Make sure both ends of your filling loop are attached

• Open both valves to allow cold water into the system – you’ll hear it start to move

• Look out for your pressure gauge to show 1.5 bar

• Close both valves

• Switch your boiler back on

• Undo both ends of your filling loop and remove it. Remember some water might come out, so be ready to catch some spillage!

A boiler is simply the most important part of a central heating system as it generates the heat that warms up the home or property. Basically, the appliance or small furnace makes use of gas, LPG or oil in order to fuel its operation. However in the UK, most boilers are usually fuelled by natural gas which is supplied automatically from the national gas grid. And depending on how it operates, there are various types of boilers.

Typically, a gas central heating boiler will have multiple pipes entering from underneath. While one pipe supplies the boiler with gas from the mains gas supply, another pipe allows cold water to enter the boiler to be heated, the last pipe then enables hot water to exit the boiler so it can be distributed around the home.

✓ There are fuel jets and heat exchangers inside the boiler. When the heating is turned on, a valve is opened to allow the mains supply gas to enter a sealed combustion chamber in the boiler. There are multiple little valves which permit the entry of the gas before being ignited by an electric ignition switch. These jets heat a metal component in the boiler known as a heat exchanger which works to transfer the heat to the cold water pipe and heat up the water.

✓ Once the water has been heated to the target temperature, it’s then pumped through a circuit of pipe which runs around your home by an electric pump.

✓ The heated water enter each radiator, is then transmitted via a closed loop and radiates heat into each room.

✓ Once done travelling through all radiators, the water then returns to the boiler at which it must have been cooled. Therefore, the boiler will have to reheat following the same process before circulating. The water can only be drained by a professional Gas Safe engineer

Condensing boilers are the in-thing when it comes to modern heating systems in UK homes and across the globe for a good reason. This is primarily due to the fact that condensing boilers happens to be highly efficient as it enables the fuel you’re burning to heat up your home go a lot further. Having a new high efficiency condensing boiler rather than an old G-rated non condensing boiler will not only enhance your heating controls, but also save you a lot of money annually. In this article, we’re going to take you through the basics of a condensing boiler. Let’s take a closer look!

If you’re interested in getting a greener and more efficient boiler, you simply can’t afford to look beyond a high efficiency condensing boiler. This is purely due to the fact that these condensing boilers happens to make a better use of the heat they’re able to produce from burning fuels like oil or gas ( in other words, they require less heat from the burner, which makes them a lot more efficient).

So how does a condensing boiler work? Unlike a non-condensing heat-nly boiler, some heat will be wasted in form of hot gases which are released from the flue. Meanwhile a condensing boiler captures some of the heat from these gases and puts them to use for heating up water that’s coming back from your central heating system. As a result, it requires just a minimal heat from the burner which make the boiler more efficient.

You should take note that all new modern boilers are condensing boilers. Therefore if you’re planning to replace an old boiler with a new one, you’ll definitely be buying a new condensing boiler and benefit from all the efficiency and savings that comes with it.