Block Paving in Bamburgh

The most commonly used driveway surfacing materials are gravel, asphalt, concrete and paving - which can be block, slabbed or patten imprinted. Take a look at our product information pages to help you decide which one to use and which one will look best for your driveway.

How To Lay Block Paving

Do you wish to know how to install block paving? We’ve got you covered! Here, you’ll find a useful step by step guide that’ll provide you with all the necessary information to lay a wide range of block paving products available in the market today. You must, however, note that the installation of block paving can be a tricky affair and should not be attempted unless you have undergone a proper training or have a good experience in the field. If otherwise, we’d advise you to leave the task for a reliable block laying professional to guarantee the best results and also avoid making costly mistakes.

lDesign

• Draw up a design to perfectly suits your needs.

• Decide on the type of block as well as colour.

lExcavation

• Use a mini excavator or a JCB ( depending on the size of the job) to excavate the driveway.

• Identify and mark out the area to be excavated.

• Dug out the area until you reach a suitable level

• Ensure that the proposed finish level is 150mm underneath the damp proof course in any of the adjoining building’s brick.

lEdge Restraints

• Build a 100mm depth-thick concrete foundation with the help of a concrete mixer, 1 part cement and 6 parts ballast.

• Position the kerb unit on top of the level with a string line and spirit level.

• Use a trowel and rubber mallet to mortar the kerb unit to the foundation.

• Haunch the back of the kerb units in such a way that the concrete reach half way up the kerb’s rear.

lSubbase

• Put the crushed concrete in the edge restraints and ensure it’s at the desired level of 50mm.

• Use a vibrating plate to compact and level

lScreeding

• Apply a layer of sharp sand (to 50mm depth) and campact it using a vibrating plate.

• Apply second layer of sharp sand (to 20mm depth) on top of the first layer.

• Level the second layer to the correct falls.

lInstallation Of Paving

• Lay the block paving starting from the bottom of a slope.

• Ensure the blocks are placed at about 10mm to 15mm above the required finish level.

• Make sure the blocks used are between 3-5 packs as you proceed with your desired pattern. You may need to cut smaller block pieces to fill smaller gaps.

lFinishing Touches

• Clear out the area to ensure no debris is left on the blocks.

• Put kiln dried sand and brush across the whole of the area, ensuring the sands falls between the blocks’ joints.

• Compact the drive with the vibrating plate.

• Brush more kiln dried sand over the area and compact again

• Repeat the process until the joints are full of sand.

Are you having weed problems on your carefully picked out block pavings? After spending huge bucks to install the block pavings, the last thing any homeowner would want to discover is weed taking over the prized asset. Fortunately, this is a problem that can be effectively handled in a few simple steps provided in this article.

Basically, sealing of block paving is all about prevention of weed growth in the area by total weed removal, putting of sand between the block paving joints and sealing with a good quality sealant. This is a task that’s best left for a reliable professional to guarantee the best results especially if you lack proper training and experience. This guide will give a good insight into the process.

Here are the equipment you’ll need to get started: pressure washer, weed killer, bin bag, broom, small brush, protective gear, sealing roller, spueegee, jointing sand and sealer and DIY sprayer.

lRemove The Weed

• Put on a protective clothing and gloves

• Get a weed disposal bag to clean while you go.

• Apply the selected weed killer on both areas where weeds are present and the absent ones to prevent any growing.

lPressure Washing

• Angle your pressure washer between the gaps. This is done to remove all weeds and debris that are still lying around as well as removing all possible chemical residues to create a thorough clean between the paving slab.

• Leave the washed area to dry.

l Sand The Joints

• Check the weather forecast to ensure there’s about 24 to 48 hours of dryness as its important for both sand and sealant to do a perfect job.

• Put sand between the gaps and push it down with your small brush until its levelled.

lSeal The Gaps

• The sealing process should be done immediately and sanding.

• Clean up the patio

• Perform a test using a small area

• Apply the sealant

• Apply the second of sealant

• Leave to dry for about 2 to 3 hours.

Is Block Paving Permeable?

Back in 2008, there was a regulation introduced which comes with a requirement guiding the pavement of front gardens. It requires homeowners to incorporate the conventional impermeable driveways which makes for an uncontrolled run off of rainwater into sewers, roadways, local watercourses etc. However since then, new systems have been established which complies with the legislation and permit driveway laying of block paving without requiring planning permission while still providing the same visually appealing features as the conventional systems. Therefore, a short and simple answer to whether block paving is permeable is yes.

A permeable paving driveway (unlike the conventional ones which quickly diverts rainwater towards the edges to local drains) purposefully diverts rainwater into the built paving structure which oversees a controlled release of the rainwater into the environment. Permeable block paving comes with a wide range of benefits which includes the following:

• No Planning Permission Required

Unlike the traditional system, permeable block paving requires no planning permission as it oversees the driveway draining by ensuring that the surface water passes directly through the joints which makes sure the drains are not over worked and minimizing the risk of flood.

• Puddles Reduction By Natural Drainage

A permeable block paving minimizes puddles as well as standing water which helps to boost natural drainage. This is due to the laying process which features little voids that permits the passage of water.

• Natural Filtration

A natural filtration occurs when water is allowed to return to the ground by permeable block paving which helps assists in getting rid of any pollutants from the rain water.

• Flood Prevention

Permeable paving can help to prevent flooding as it absorbs water rather than directing it to the local drains or leaving it to build up on the surface’s top.

• Natural & Sustainable Materials

Natural and recyclable materials can be incorporated in producing permeable paving which is an excellent choice especially if you’re seeking a more sustainable driveway.