Block Paving in Balerno

Your contractor should have access to your driveway and a power source. If they have these things, you don’t need to be there while they’re working on your driveway. However, it’s worth being around if you can so you can clarify details and answer any questions.

Have you decided to install block paving and wondering what the best sand to be applied to the joints is in order to achieve a perfect job? Well, you’re at the right place! This is one of the most frequently asked questions when it comes to block paving and we seek to give you a reliable solution once and for all.

The best sand for block paving is a kiln-dried sand. It’s an extremely fine sand which has been dried in a kiln to get rid of all the water before it’s incorporated to achieve the best results. Therefore, the sand contains no moisture and is commonly used to fill the joints of block paving to keep the paving’s structure rigid and strong. It also goes a long way to prevent the ingress of water while stopping the paving from moving and becoming loose. The major reason why the paving sand must be dried is to allow it flow easily into the joints as well as the block paving’s gaps. As result of this smooth flowing to the bottom of the joints, there will be no sand sticking to the sides of the pavers.

Another major reason why kiln-dried sand is commonly applied to the block paving’s joints is to prevent water from penetrating the paved area. It also tightens the individual pavers together to prevent from moving and becoming loose. In the event whereby you happen to leave the joints of your block paving without kiln dried sand, it’s highly likely that they’ll sink as a result of water penetration and the blocks will become very loose. After washing block paving, it’s very important to also replace any sand washed off in the process once the paving is dried to prevent water ingress into the joints.

How To Lay Block Paving

Do you wish to know how to install block paving? We’ve got you covered! Here, you’ll find a useful step by step guide that’ll provide you with all the necessary information to lay a wide range of block paving products available in the market today. You must, however, note that the installation of block paving can be a tricky affair and should not be attempted unless you have undergone a proper training or have a good experience in the field. If otherwise, we’d advise you to leave the task for a reliable block laying professional to guarantee the best results and also avoid making costly mistakes.

lDesign

• Draw up a design to perfectly suits your needs.

• Decide on the type of block as well as colour.

lExcavation

• Use a mini excavator or a JCB ( depending on the size of the job) to excavate the driveway.

• Identify and mark out the area to be excavated.

• Dug out the area until you reach a suitable level

• Ensure that the proposed finish level is 150mm underneath the damp proof course in any of the adjoining building’s brick.

lEdge Restraints

• Build a 100mm depth-thick concrete foundation with the help of a concrete mixer, 1 part cement and 6 parts ballast.

• Position the kerb unit on top of the level with a string line and spirit level.

• Use a trowel and rubber mallet to mortar the kerb unit to the foundation.

• Haunch the back of the kerb units in such a way that the concrete reach half way up the kerb’s rear.

lSubbase

• Put the crushed concrete in the edge restraints and ensure it’s at the desired level of 50mm.

• Use a vibrating plate to compact and level

lScreeding

• Apply a layer of sharp sand (to 50mm depth) and campact it using a vibrating plate.

• Apply second layer of sharp sand (to 20mm depth) on top of the first layer.

• Level the second layer to the correct falls.

lInstallation Of Paving

• Lay the block paving starting from the bottom of a slope.

• Ensure the blocks are placed at about 10mm to 15mm above the required finish level.

• Make sure the blocks used are between 3-5 packs as you proceed with your desired pattern. You may need to cut smaller block pieces to fill smaller gaps.

lFinishing Touches

• Clear out the area to ensure no debris is left on the blocks.

• Put kiln dried sand and brush across the whole of the area, ensuring the sands falls between the blocks’ joints.

• Compact the drive with the vibrating plate.

• Brush more kiln dried sand over the area and compact again

• Repeat the process until the joints are full of sand.

Can You Lay Block Paving On Top Of Concrete?

The replacement or improvement of your driveway is unarguably one of the most expensive projects you can undertake in the exterior of your home. When done by a true professional the results can be impressive and visually appealing, however you’d have to pay huge bucks to have this done. This is exactly the situation with block paving as it is not only time consuming, but also a lot more expensive when compared to other types of driveway.

A large chuck of this cost is associated with the removal of the existing driveway. So assuming your old driveway is concrete, can you simply pave over the existing concrete? If yes, will it save you money? The simple and short answer is yes. It’s in fact advisable to pave over concrete as this will not only add around 20% to your home’s value, but also make it look a lot more attractive and pleasing to the eye.

However, there are some problems associated with block paving over concrete. It may be better to remove the concrete in situations whereby the base is substandard. For instance, if the ground underneath the concrete is failing, there’ll most definitely be problems.

Also, there’ll be some issues with settling (not even the cracks). If your concrete is dropping little amounts every year, these can affect the blocks and ultimately lead to dropping of some sections of the block paving in such a way that they’ll no longer be on the same level as the other blocks. Giving a rise to the possibility of drainage issues, tripping hazard and lots more.

Other issues that may crop up can be triggered as a result of using the wrong size block height as well as totally ignoring or overlooking the undulations of the concrete.