Boiler (Pay-Monthly) in Edgware

When it comes to gas boilers, this is one of the most frequent questions that always pops up and for a good reason. When you invest a considerable amount of money to acquire and install a gas boiler in your home or property, it’s only reasonable not only to expect the boiler to warm up your home efficiently, but also to do so for a long period of time. If you’ve just bought or about to get a new gas boiler, it’s likely you won’t have to worry about getting a replacement for a lengthy period of time. Several gas boilers will last for anywhere between 10 to 15 years on the average. However in the event whereby you have an existing one that’s fast approaching the end of it’s useful life, then you should know the time go get a new gas boiler is just around the corner, and the earlier you make the purchase, the better (to avoid any surprise breakdowns that’ll leave your home super uncomfortable).

Just like any other home appliance, it’s a fact that an older gas boiler ( especially those that have been installed over a decade ago) are significantly less efficient that the new modern ones. When the older versions were manufactured is a completely different time to now as both technology and climate concerns are wide apart. So when your existing boiler is approaching the end of it’s useful life, it’ll be wise to start saving up to cover the cost of getting a new one. However, if it’s only about 5 years ago your boiler was installed, it’s highly likely to still be very efficient.

Re-pressurising your boiler means that you allow more water to enter system via the filling loop. It can be easy to re-pressurise your boiler yourself. Always check your manual, but there are some simple steps you can take to restore pressure to your boiler:

• Switch off your boiler and let it cool completely

• Make sure both ends of your filling loop are attached

• Open both valves to allow cold water into the system – you’ll hear it start to move

• Look out for your pressure gauge to show 1.5 bar

• Close both valves

• Switch your boiler back on

• Undo both ends of your filling loop and remove it. Remember some water might come out, so be ready to catch some spillage!

A boiler is simply the most important part of a central heating system as it generates the heat that warms up the home or property. Basically, the appliance or small furnace makes use of gas, LPG or oil in order to fuel its operation. However in the UK, most boilers are usually fuelled by natural gas which is supplied automatically from the national gas grid. And depending on how it operates, there are various types of boilers.

Typically, a gas central heating boiler will have multiple pipes entering from underneath. While one pipe supplies the boiler with gas from the mains gas supply, another pipe allows cold water to enter the boiler to be heated, the last pipe then enables hot water to exit the boiler so it can be distributed around the home.

✓ There are fuel jets and heat exchangers inside the boiler. When the heating is turned on, a valve is opened to allow the mains supply gas to enter a sealed combustion chamber in the boiler. There are multiple little valves which permit the entry of the gas before being ignited by an electric ignition switch. These jets heat a metal component in the boiler known as a heat exchanger which works to transfer the heat to the cold water pipe and heat up the water.

✓ Once the water has been heated to the target temperature, it’s then pumped through a circuit of pipe which runs around your home by an electric pump.

✓ The heated water enter each radiator, is then transmitted via a closed loop and radiates heat into each room.

✓ Once done travelling through all radiators, the water then returns to the boiler at which it must have been cooled. Therefore, the boiler will have to reheat following the same process before circulating. The water can only be drained by a professional Gas Safe engineer

If you’re thinking about getting a new gas boiler for your home or property, then you might also be wondering how much it’ll cost you so you can set a budget and start planning. As simple as this question sounds, it’s actually very tricky to provide a simple and short answer as the costs of installing a new gas boiler alone varies greatly based on the parts needed, the amount of work required, your location, their availability as well as the company you hire for the project.

When it comes to purchasing a new gas boiler the price you’re expected to pay also depends on multiple influencing factors such as the type, brand as well as your most preferred gas boiler model. However, one thing you should have in mind is the fact that your gas boiler is right at the heart of your home or property and can be a complicated piece of machinery. As a result, you wouldn’t expect gas boilers to come cheap. Generally, it’s going to cost within the range of £500 to about £2,500 to get a new gas boiler. Therefore, it’s always advisable to obtain all necessary details and facts before you decide to purchase a replacement gas boiler.

This price range may seem too high as it’s usually a turn off for most homeowners. However, it’s worth noting that gas boiler replacement costs and gas boiler installation costs are, more often than not, compensated by the saving you’ll make off your utility bills - all thanks to the new and more energy efficient boiler you just installed in your home. And even more importantly, when it has been estimated that roughly half of the amount spent on energy on an annual basis depends on your boiler.