Gas Boiler (Repair & Servicing) in Cornhill-on-tweed

No. You must never repair your own boiler – only a Gas Safe-registered engineer can do any work on your boiler. You can do simple DIY tasks to repressurise your boiler or stop a leak, but if you have to remove the outer casing of the boiler or touch the flue then you must get a qualified boiler engineer to take a look at your central heating system.

If your boiler is leaking, there are some checks that you can do yourself. However, you should never attempt to repair your boiler yourself – only a Gas Safe-registered engineer should conduct repairs.

There are 3 main reasons why your boiler might be leaking: there’s a pressure valve fault, a temperature valve leak or corrosion in the system. An engineer will be able to spot the problem quickly, but in the meantime there are a few things you can do:

Check the pipe fittings

If your boiler is leaking water around the pipe fittings, it could be an installation fault and you should get in touch with the engineer that fitted it. You can check the pipe fittings by drying the area then waiting to see if the water appears again. If it does, you may be able to do a ¼ turn of the pipe to stop it. However, you should still call the engineer that installed it to ask them to check the PTFE tape on the inside.

Inspect the seals

Over time, the rubber seals on a boiler can start to perish, so if you have an old boiler this could be the source of your leak. If you have a new boiler, it could be caused by your boiler running over pressure.

Heat exchanger corrosion

Unfortunately, if a boiler engineer discovers that the boiler is leaking water from the heat exchanger, this is the end of the road for your system. The heat exchanger is the most expensive part of your boiler, so it makes more financial sense to replace your boiler with a newer, more efficient model rather than try to replace it.

Can I Repair My Own Gas Boiler?

If you’re more of an handy person, then you’d probably want to fix everything you can around the house while saving yourself some money that would have been spent on hiring a professional instead. This is a very cost effective but at the same time you must know that some tasks are usually more difficult than others, and a good example of those complex tasks is boiler repair. Not only can this be very tough, but they can also potentially be one of the most dangerous home appliances you can acquire. So with that in mind, what can be done to ensure your gas boiler is taken care of and in the event whereby it starts to malfunction, what can be done to remedy the situation?

With regular maintenance and repair of your gas boiler, you’d have absolutely nothing to worry about. However one of the fear several DIYers have is the fact that they might just end up incurring more expenses on services they didn’t really need in the first place. But when it comes to gas boilers, it’s necessary to be certified to work with them as it’s very dangerous to tackle it all by yourself. Despite this, there are still some minor issues that you wouldn’t need to hire a technician to resolve. In some cases, all that would be needed is simply to reset the boiler. To identify where the reset button is, simply go through your boiler’s manual for more information. Most times, all you’ll have to do is press down the reset button for a couple of seconds. If the boiler isn’t fully restored to its normal proper functioning state after two resets, then you may need to call in a professional for help.

How To Fix A Broken Boiler

To fix any problem when it comes to home appliances, the first step is always to identify the problem while also carrying out thorough checks - a broken boiler is not an exception. Putting enough time and effort in diagnosing a problem can go a lot way to save you both time and money. So here are some of the steps you can take to fix your broken boiler before you put a call out to a licensed engineer.

✓ Check to confirm if your pilot light is on. Whenever you’re facing some issues with your boiler, this should always be the first thing you do. The pilot light being on speak volumes, if the light is off then there’s absolutely no way the flame can start the appliance’s gas supply. You should try to put it back on, if off. To do this, you simply have to follow the detailed instructions on your boiler’s manual strictly. If after following these actions to the letter and the issue remains the same, then you’d probably need the services of an a qualified engineer. Never try to fix the issue on your own.

✓ Check the pressure. The solution to the headaches might sometimes be as simple as examining your appliance’s pressure gauge. Here, the good numbers are around 1.0 or1.5, if it happens to fall below this, then you should open the boiler’s instruction manual. You can also inspect your radiator valves for any leaks. You’d have to call in a specialist to solve the issue.

✓ Check the thermostat. Here, it’s important to note that a faulty thermostat doesn’t necessarily imply a broken boiler. It may just signify that you need to replace your thermostat. Simply check to ensure that your thermostat is turned on and temperature is at the appropriate degree.