Question 1

How to build a raised deck?

Accepted Answer

Building a raised deck will take some time and is trickier than laying standard decking at ground level, but if you want to build decking on a slope or uneven ground it’s the best way to do it. If you do your research and follow instructions, you and a friend or family member can build a raised deck over a few days. Here’s a simplified guide of the steps you’ll need to take. Plan carefully It’s best to plan your raised deck by drawing it to scale on paper before you go and get supplies. This will help avoid wastage and making more cuts to timber than necessary. Prepare the area Prepare the area according to the instructions we give in the FAQ ‘How to lay decking’. However, because you’re building a raised deck, you’ll need to add posts: Place a post in the corner of the frame you created with the pegs and string. Measure and mark out 100mm from each side. Dig out this soil to a depth of 700mm (watch out for cables or pipes). You should have a 300 x 300mm hole. Repeat for the other 3 corners. Using a brick bolster, split a concrete block in two. Put a section of the block in each hole. Get a length of post longer than you need and place one in each hole. You can cut it down later. Create props on each post to hold them in place until you’re ready to add a cement mix. Check that they’re level. When you’re happy that they are, secure them in place with a concrete mix, making sure you create a slope in the concrete so that rainwater runs away from each post. When the concrete is set, remove the props. Create a string line around each corner post and find the centre point between each. Place a timber batten at each point, ensuring that they’re not spaced any more than 1500mm apart. Make the outer frame Working from the corner where the deck will be at its highest above ground level, measure and mark on the post where the highest part of the frame will be. Measure from the far side of one post to the opposite and cut sections of joist to size. Line up a piece of joist with the mark you made and temporarily secure it. Factor in a 2mm fall for every metre of decking so rainwater can run off. Secure the frame to the other corner post, ensuring it’s at the right level. Do this for every side of the outer frame. Using 100mm coach screws with washers hanging on the end, secure each end of the four sections of frame. Mark out where the centre of the support posts will be and secure all of these posts to the frame, except the centre post. Add your central support joists. These should run in the same direction as the deck boards will run. You’ll need to measure from the inside of the frame on one side to the inside of the frame on the opposite side. Attach the joist in the same way as you did for the other posts. Repeat so the centre post is in between two sections of frame and secure the posts with concrete. Trim down all the posts to the correct height using a saw. Add your weed-control fabric and weigh down with gravel across the entire area. Add your joists Measure 400mm from the centre of the outer frame and mark a line. This will be where the first joist is positioned. Repeat at 400mm intervals down the length of the frame – if the last one will be more than 400mm, add another joist to create enough support. Attach a joist hanger to each end of the joist. Place the joist in position so the centre lines up with the 400mm spacer mark. Secure using external grade screws once you’re happy that the joist is flush with the frame. Lay your decking boards Refer to our FAQ on how to lay decking to see how you should attach your decking boards. Remember: Always treat cut ends and pilot holes with decking preservative to keep your decking in good condition for as long as possible. Building a raised deck isn’t a straightforward task. If you’d rather leave it to the professionals, get a range of quotes to help you get the best price and a high quality finish.

Question 2

How to fit composite decking?

Accepted Answer

Fitting composite decking is similar to installing timber decking, but there are some small differences in terms of the gaps you need to leave between boards and the screws you use. We’ll go through a quick guide to show you the process involved in fitting composite decking so you can decide whether it’s something you want to do yourself. Prepare the area Prepare the area according to our instructions in the previous FAQs – or you can use an existing patio or concrete base if you have one. Measure and mark out the area using chalk (if using an existing base). Assemble the decking frame Build the outer frame as we show in our FAQs above; if the area you have planned is longer than your joists, you’ll need to join them together. When you’ve built the frame and it’s secure, ensure that it’s at the right level for water runoff and add risers, slabs or treated off-cuts of timber at 500mm intervals if you need to. Add joists The spacing of your joists will depend on the type of design you have chosen for your composite decking. If you’re laying arched boards horizontally, you’ll need to space the joists 300mm apart. Lay your composite decking boards If you’ve not got an overhang or it’s a fixed deck, fit starter clips along the outside edge of the frame and secure with screws provided with the composite decking. If you are working with an overhang, put the first board into position not exceeding 25mm. If you’re adding a fascia, put an off-cut of board under the overhang so you know it’ll be flush with the fascia. Pre-drill all fixing points, measuring in 30mm from the edge of the board. Secure the board to the joist below with composite decking screws. Slide a hidden fastener clip in so it sits within the groove of the deck board. It needs to be in the centre of the joist to keep the boards secure and ensure an expansion gap of 6mm. Tighten the clips until just tight, and repeat so there’s a clip at every joist. Add the next board, ensuring that the fastener clips sit within the groove – make sure you don’t force it. Repeat step 3. Continue steps 3 and 4 until you’re at the final board, which you should secure in the same way as you did the first. Add a fascia board If you’re adding a fascia, measure in 40mm from each end and add two guide marks: one at 40mm from the top and the other at 40mm from the bottom. Connect the marks, then mark at 300mm intervals down the board. Drill pilot holes, then put the fascia board into position. You need to make sure that there’s a 40mm ventilation gap between the bottom of the fascia and the ground. Ask someone to hold the board level until you’ve finished securing it with composite decking screws; you can get colour-matched ones so they don’t look unsightly at the end of your decking. Not so sure you want to carry out such a big project yourself? Get quotes from decking pros who will be able to fit composite decking much more quickly and easily.

Question 3

How much is decking?

Accepted Answer

How much decking costs depends on the type of material you go for, how big you want your decking to be and where you live in the country. But typically, the cost of decking is between £1,200 - £1,800. The most popular material for decking is pre-treated softwood, which will set you back around £1,000 for 15m2. Hardwood is more expensive but is more durable, and will cost approximately £2,000 for the same amount. Homeowners are also beginning to choose composite decking, which is made from recycled plastic and wood fibres, and is low-maintenance and eco-friendly. This will cost around £1,600 for 15m2, while uPVC which is also a low-maintenance option costs around £600. People tend to choose composite over uPVC because it looks more like natural timber. If you’re a competent DIYer, you might want to have a go at laying decking yourself which will set you back around £1,000 for a standard softwood timber deck. We think it’s worth paying the extra £600 for a professional to lay your decking, since they will be able to do it much more quickly. If you do want to try it yourself, we recommend leaving at least a whole weekend open to do it, but it’s likely to take you longer. Factor in the possibility of having to take time off work to complete it and it might be more cost-effective to leave it to the pros.

Question 4

How to make steps for a deck?

Accepted Answer

Unless you built a ground-level deck, you’re going to need steps to go with it. Check Building Regulations to see if you need to install handrails as well. It’s good practice to: Have a step tread width of 900mm – if you don’t want them that wide, they should be no less than 760mm Add a central step riser to stairs wider than 900mm to prevent them buckling Add a step depth (the vertical distance between each step) of between 150 and 180mm if building your own riser, so the steps are at a comfortable depth Getting started To build your steps for the deck, you’ll need: Step treads (the actual step themselves) Step risers Coach screws Deck screws Saw Drill Make the steps for your deck Make sure the ground where you want to put your steps is level and firm. If it’s not, consider laying concrete or paving slabs to provide a secure surface for your steps to sit so they don’t sink. Grab some joist off-cuts and cut them to the same width as your step treads. Attach them to the step risers at the top and bottom using countersunk coach screws. Place the steps against the sub-frame of the deck; if you’ve put slabs down for support, make sure the steps sit in the middle of them. The longest edge of the stair riser should be on the slabs, and the short edge against the deck. Drill pilot holes through the step and sub-frame joist, then screw the step to the sub-frame with more coach screws. After drilling pilot holes, screw the treads into the risers at each end with deck screws. If you don’t want gaps between each stair, you can add joist off-cuts or deck boards. Measure the height and depth of the gap, then screw the off-cut or board into the step riser with two screws at each end.

Avg. price low	Avg. price low £1,125
Avg. price	Avg. price £1,500
Avg. price high	Avg. price high £1,725

	Labour cost	£1,050
	Material cost	£375
	Waste removal	£75

Wooden Decking in Rhyl

Discover Wooden Decking Prices in Rhyl

Wooden Decking in Rhyl

Average Wooden decking cost in Rhyl

Average price per Wooden decking job in 2025

Wooden decking installation cost in Rhyl 2025

Wooden decking searches in February 2025

Wooden decking Projects in Rhyl in January 2025

1,931

0

0

Wooden decking searches in cities and towns near Rhyl January 2025

Wooden decking near you

Rhyl

Looking for Wooden decking in Rhyl?

Get free quotes from local carpenters

Similar Customer Enquiries for Wooden decking in Rhyl

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Local & reliable carpenters near me

Tell us about your wooden decking project

Find up to 4 carpenters in Rhyl

Hire with confidence

Our reviews

Average

Would highly recommend

Good easy way to find a selection of…

Love LeadsDoWork it's a big part of my …

FAQs

Other Top Projects in Rhyl

Need more help?

Are you a carpenter in Rhyl?