Wall Tiling in Twickenham

If you’re not an expert floor installer who would take wall tile installation as merely being a vertical floor, you are advised to be very cautious when tackling the project. The installation of wall tiles follow some set of rules which you’d better not break if you really wish to protect your investment. And worst of all, a wall tile done wrong is a lifetime penalty of having to look at it. So how can you get it right? Well, probably by reaching out to a wall tile installation professional for a good quality solution that’ll save you time, money and effort. However, we’ve put together this guide to help give you an insight of how it works and also to help you avoid some unnecessary expenses. Let’s have a look!

• Hang a batten board

✓ Start your rows of tiles or bottom-most course with a batten board which works to prevent spillage of tiles.

✓ Position the batten board at 3/4 of the tiles’ height. Ensure not to start at the floor.

• Form A Pyramid Shape With The Tiles

✓ If you’ve reached the bottom row of tile, then arrange the tile in a pyramid shape. To achieve this, you’d have to install the tiles one through four as instructed. Each following row will be draped over the pyramid.

• Examine The Floor For Level & Walls For Plumb

✓ If your floor level or plumb is off by a maximum of a half-inch over the course of 8 feet, add extra baseboards and trim to cover up the problem.

• The Least Size Of Tiles To Be Used Is Half-Wide

✓ Ensure that no “silvers (tiles that are lower than half the width of the tile in question) are incorporated in the project.

Once a tile is glued to a wall, it’s meant to stay there permanently. As a result, if you later decide to remove the wall tile, this process often involves destruction of the tile. However, if you only wish to have a portion of the tile removed, there’s a technique you can incorporate to achieve this goal. Using an angle grinder or rotary tool to cut through the tile enables you to detach the unwanted tile portion from the wanted portion. In other words, you can remove only a section of the tile, while leaving the rest intact and undamaged. So, how do you cut tile on wall? In this post, you’ll discover all you need to cut tile on your wall successfully. Let’s take a look!

• Protect the area. Do this by using plastic sheet taped firmly into place with masking tape to cover doors leading to other areas of the house to prevent dust coming from the cutting process from getting everywhere in the house. You can also cover the vents while also opening the windows to provide ventilation.
• Make a mark on the cutline you’ll be making using a grease pencil. Then, place masking tape on the tile running along the edge of the marked line.
• Use a handheld sprayer filled with water to spray the tile surface so as to prevent the dust generated from the cut to spread while also provide lubrication for the cutting blade.
• Use an angle grinder to cut through the tile.
• Use a small pry bar positioned in the joints to pry cut pieces from the surface.
• Remove the dust created using a vacuum and wash the surface with a water dampened rag.

If you planning to invest in wall panels, it’s worth knowing whether or not they can be fitted over tiles. With the right installation advice from a reliable source, you’ll be able to save yourself both valuable time and money while also making sure that your home improvement project adds immense value to your property and gains from a durable and long lasting finish.

Wall panels, in general, are a cost effective means that you can incorporate to waterproof your bathroom or shower walls, while they’re also known for being incredibly stylish. Another significant benefit, that’s rather surprisingly often overlooked, is the fact that it’s actually a lot easier to clean and maintain when compared to wall covering that incorporates grout.

The short and simple answer to this question is yes, you can fit shower wall panels over tiles. However, it should also be noted that these may not be possible depending on your existing tiles’ conditions. This is because there are tiles that may not be suitable to be covered by shower wall panels. To protect the integrity of your shower wall panels and continue to enjoy it for any extended period of time, there’s a need to ensure that the existing tiles are in the right condition before you proceed. A beautifully finished and mould free bathroom will make your home stand out while also adding more value to it.

As a result, you’ll have to carefully inspect the tiles on the walls you want to cover before you proceed. While the odd cracked tile on a flat surface may not be an issue, all loose tiles should be completely removed (if more than two, you may want to consider removing all). You’ll also need to address other issues like damp or degrading plaster, uneven wall and more.

Thanks to its durability, resistance to moisture and stain as well as aesthetic appeal, ceramic tile is a popular material for floor installations. The same qualities that makes it stand out for both kitchen and bathroom floors also makes it a natural choice for walls.

Fitting of ceramic wall tile is a task that requires pre-planning and lots of patience. Generally, it’s usually not that difficult to do but it can be very easy to make mistakes here and there. And because you’ll have to attach a relatively heavy material to vertical surfaces, the project can be somewhat trickier than ceramic floor tile so more care and skill is required here. This can be done by any competent DIYer who is confident and also patient. If you lack any of these attributes, we’d recommend you call in a professional who can guarantee the best results for help. In this article, we’ll take you through the ceramic wall tiles fitting process. Let’s take a look!

✓ Prepare the room. This includes switching off power to electrical outlets, removing decorative wall plates and other accessories on the wall, protecting the surface and taking out the baseboard.

✓ Draw reference lines. Using a chalk line draw a reference line on the wall to be tiled.

✓ Spread the adhesive. Use a notched trowel to spread the tile adhesive

✓ Install the first tile. Use the reference line as a guide to fit the first tile near the centre of the wall, twisting it slightly so its firmly in place. Then check to ensure the tile is level and adjust if you deem fit.

✓ Install all tiles. Following similar technique to install the remaining tiles and use tile spacers to ensure even gaps

✓ Clear out excess adhesive and remove spacers.

✓ Apply grout. Dampen the grout with clean water before the grout application

✓ Caulk the joints. After like 10 days, use silicone sealer to caulk the expansion joints.