Wall Tiling in Brent

Thanks to its durability, resistance to moisture and stain as well as aesthetic appeal, ceramic tile is a popular material for floor installations. The same qualities that makes it stand out for both kitchen and bathroom floors also makes it a natural choice for walls.

Fitting of ceramic wall tile is a task that requires pre-planning and lots of patience. Generally, it’s usually not that difficult to do but it can be very easy to make mistakes here and there. And because you’ll have to attach a relatively heavy material to vertical surfaces, the project can be somewhat trickier than ceramic floor tile so more care and skill is required here. This can be done by any competent DIYer who is confident and also patient. If you lack any of these attributes, we’d recommend you call in a professional who can guarantee the best results for help. In this article, we’ll take you through the ceramic wall tiles fitting process. Let’s take a look!

✓ Prepare the room. This includes switching off power to electrical outlets, removing decorative wall plates and other accessories on the wall, protecting the surface and taking out the baseboard.

✓ Draw reference lines. Using a chalk line draw a reference line on the wall to be tiled.

✓ Spread the adhesive. Use a notched trowel to spread the tile adhesive

✓ Install the first tile. Use the reference line as a guide to fit the first tile near the centre of the wall, twisting it slightly so its firmly in place. Then check to ensure the tile is level and adjust if you deem fit.

✓ Install all tiles. Following similar technique to install the remaining tiles and use tile spacers to ensure even gaps

✓ Clear out excess adhesive and remove spacers.

✓ Apply grout. Dampen the grout with clean water before the grout application

✓ Caulk the joints. After like 10 days, use silicone sealer to caulk the expansion joints.

If you’re not an expert floor installer who would take wall tile installation as merely being a vertical floor, you are advised to be very cautious when tackling the project. The installation of wall tiles follow some set of rules which you’d better not break if you really wish to protect your investment. And worst of all, a wall tile done wrong is a lifetime penalty of having to look at it. So how can you get it right? Well, probably by reaching out to a wall tile installation professional for a good quality solution that’ll save you time, money and effort. However, we’ve put together this guide to help give you an insight of how it works and also to help you avoid some unnecessary expenses. Let’s have a look!

• Hang a batten board

✓ Start your rows of tiles or bottom-most course with a batten board which works to prevent spillage of tiles.

✓ Position the batten board at 3/4 of the tiles’ height. Ensure not to start at the floor.

• Form A Pyramid Shape With The Tiles

✓ If you’ve reached the bottom row of tile, then arrange the tile in a pyramid shape. To achieve this, you’d have to install the tiles one through four as instructed. Each following row will be draped over the pyramid.

• Examine The Floor For Level & Walls For Plumb

✓ If your floor level or plumb is off by a maximum of a half-inch over the course of 8 feet, add extra baseboards and trim to cover up the problem.

• The Least Size Of Tiles To Be Used Is Half-Wide

✓ Ensure that no “silvers (tiles that are lower than half the width of the tile in question) are incorporated in the project.

Once a tile is glued to a wall, it’s meant to stay there permanently. As a result, if you later decide to remove the wall tile, this process often involves destruction of the tile. However, if you only wish to have a portion of the tile removed, there’s a technique you can incorporate to achieve this goal. Using an angle grinder or rotary tool to cut through the tile enables you to detach the unwanted tile portion from the wanted portion. In other words, you can remove only a section of the tile, while leaving the rest intact and undamaged. So, how do you cut tile on wall? In this post, you’ll discover all you need to cut tile on your wall successfully. Let’s take a look!

• Protect the area. Do this by using plastic sheet taped firmly into place with masking tape to cover doors leading to other areas of the house to prevent dust coming from the cutting process from getting everywhere in the house. You can also cover the vents while also opening the windows to provide ventilation.
• Make a mark on the cutline you’ll be making using a grease pencil. Then, place masking tape on the tile running along the edge of the marked line.
• Use a handheld sprayer filled with water to spray the tile surface so as to prevent the dust generated from the cut to spread while also provide lubrication for the cutting blade.
• Use an angle grinder to cut through the tile.
• Use a small pry bar positioned in the joints to pry cut pieces from the surface.
• Remove the dust created using a vacuum and wash the surface with a water dampened rag.

Mosaic tiles is a popular choice amongst most homeowners for several reasons. Not only can they be used to create a colourful and beautiful background for your space, they’re also very easy to maintain while also lasting a very long period of time when properly installed. In addition, they’re very easy to install and can also blend perfectly with other types of tiles. If you’re thinking about fitting mosaic wall tiles in your home or office, you’d probably want to know how you can go about the installation. The installation process is actually very easy but if you do not have the confidence required to pull this off, then we’d recommend you call in a reliable professional who can guarantee the best results for help.

✓ Prepare the surface. This involves switching off the power to electrical outlets, removing wall plates as well as other accessories anchored to the wall and protecting the countertop and other surfaces.

✓ Draw reference lines. Determine the layout of the mosaic tiles.

✓ Install a tile finishing trim. This should be done at the edge of the tiled surface with flat head nails. Then use a 3/16 inches notched trowel to spread a thin coat of tile adhesive over a small section of wall, to one side of the vertical line.

✓ Spread the adhesive. Use the notched side of a trowel to spread the adhesive.

✓ Lay the first sheet. Use the reference lines as a guide to the first mosaic tile sheet.

✓ Verify adherence. Push the sheet gently into the adhesive to ensure that it adheres very well to the wall.

✓ Tap the tiles lightly. Use a rubber mallet to tap the tiles lightly to ensure the sheets are set firmly on the wall.

✓ Caulk the joints.