Single Double Glazed Window in Dumfries

Unfortunately, you can’t fix the glass on one side of a double glazed window. That’s because they’re sealed units – once one pane of glass is broken, that will break the seal and its thermal insulation properties will be lost.

The good news is that if your window frame is still looking great, there’s no need to replace that. You can simply replace the glass in the window, which will cost much less. You can look to spend around £250 on a sealed unit, whereas a whole replacement single window may cost up to £600.

When an installer comes to replace the glass in your double glazed window, they will survey the inside and outside of your home around the window, then move any furniture by the window so they’ve got access. They should then pop a dust sheet down to stop any debris from getting on your floor.

Then, the installer will carefully remove the beads from the frame. They will then lift the glass out of the frame and put it somewhere safe before cleaning out all of the dust and any debris that has found its way into the frame. Using spacers at the bottom of the frame, the installer will make sure that the sealed unit is square in the frame to get a good fit. Once they’re happy, they will replace the beading and make sure it looks perfect before cleaning up their tools.

You could have a go at replacing the glass on a double glazed window yourself, but it’s not recommended. Leave it to the professionals who will know exactly what to do and will be able to do it quickly and safely.

It depends on a few factors whether a new double glazed window will look different to existing ones. If your existing windows are very old, perhaps 10 years or more, then it’s likely that there will be some small differences.

The first thing to remember is that your double glazing is exposed to the elements as soon as it’s installed. So over time, unless you’re very good at cleaning and maintaining your windows, they’re likely to look a bit dirty. Window frames that are south-facing may also become slightly discoloured from the sun, so if you install a new window right next to it you might notice a difference.

Also, there have been lots of technical advances in windows over the years. If your existing windows are significantly older, you might notice a difference in the handles on openers, and if your existing windows were installed before 2010 they might not have trickle vents, which is an extra strip on the inside of your window to keep air flowing through your home. While it’s not a legal requirement for replacement windows to have trickle vents if the original one didn’t, it’s a good idea to have them installed as they help prevent condensation and mould.

The only truly noticeably different elements to a new double glazed window compared with existing ones are likely to be on the inside, which might not be a problem for you if you only have one window in a room. However, if you know the brand of your existing windows, you can ask your window installer if they can source the same ones. Even if they’ve been updated slightly, the difference should be minimal.

To install one small double glazed window, it will take anywhere between two hours and half a day. It will depend on whether one installer is fitting your window or two. And if you’re doing it yourself and don’t have any professional experience, it will take even longer.

When the window fitters arrive, they will make sure they’ve got safe access to the window and move any heavy furniture if they need to. Any good installer will lay down a dust sheet, but it’s a good idea to check that they’ve got one laid down before they start.

The first step any window installer will take is to double check the measurements of the new frame against your existing one. Hopefully it should match up, so then they’ll take the old window out. Then, they’ll insert the new frame into the aperture and bolt it into the concrete. They'll check it with a spirit level to ensure it’s even before moving onto the glass sealed unit.

The installer will place the glass into the aperture, then fit the beads to secure the glass in the frame. They’ll then use silicone and trim on the inside and outside to ensure the window looks perfect. You won’t be able to see where they’ve used sealants or trims because they’ll colour match them so it’s not noticeable. Then, they’ll tidy up all of their tools and the working area and let you know what needs to be done in terms of proving that the window meets building regulations. Most good installers are registered with a self-certification scheme, so will be able to issue a certification once the work is complete.