Find a Builder you can trust near you.

Render serves two basic functions. One is it’s protective qualities as render acts as waterproof for the wall which enables them breathe by allowing water vapour move from the inside to the outside of the structure while also working to prevent water or rain from finding its way inside the structure. While the second function is the decorative qualities as render is able to provide the structure with a fine finish and colour to make the building a lot more appealing and correcting faults in line and level in the masonry.

If you wish to apply render on your external wall, you’d probably be wondering just how thick the render should be to perfectly serve both of functions. In this article, we’re going to take a look at just that!

For a render thickness, the British Standard Wind Driven Rain Index has come up with 4 ratings which include Sheltered, Moderate, Severe as well as Very Severe. An area with Very Severe rating include South West England. This rating implies that the thickness of the render in this area should be increased to at least 20mm for a direct one coat render applications as well as 5 to 6 external wall insulation base coat applications. And if you happen to reside within one mile of the coast, it’s strongly recommended you incorporate an extra repellent protection like Paraguard AG from Parex.

In general, render that’s prepared on site with cement and sand should be have a minimum of 20mm to 25mm thickness. Although, it should be noted that the quality of the render is based on quality of the sand incorporated, the design mix as well as being largely dependent on how good the mixing technique from the applicator is. The most common reasons why traditional renders fails is due to both poor mixing ratios and low quality materials used.

If you’re considering converting a barn or buying one, you shouldn’t need to worry about it being cold. This is because building regulations dictate that when you convert a barn, you need to insulate it to meet specific standards. However, it’s worth considering its heating system and ceiling heights carefully – some barn conversions are likely to take longer and be more expensive to heat up than others.

How To Fit Plasterboard

If you’re planning to renovate your house, then here is a must-read guide! Fitting of plasterboard is a crucial step when it comes to renovation. If you’re bringing down an existing lath and plaster for an upgraded surface or adding a new wall, a plasterboard is required for your project to be a true success. If you’re a novice with no prior practice or experience, you can protect your investment by hiring the services of a professional plasterer to guarantee the best results, the first time. However, we’ve put together this guide to give you an insight on how the plasterboard fitting process is done.

To get started, you’ll need a power drill, hammer, plasterboard nails or screws, broad knife, utility knife, measurement tape, pencil, ladder as well as a joint tape.

Before proceeding, you need to identify the number of plasterboard sheets needed to commence the project by measuring the height and width of the wall as well as calculating the square footage. If you possess a stud timber wall, the steps below will get you the best results.

• Measure the walls and mark the plasterboard where you’ll make the cuts. Start with a full sheet and cut pieces down in such a way that would fit

• Score the front paper of the plasterboard with utility knife. Fold the sheet to get a clean cut through the board and make use of the knife to the remaining paper.

• Place the first sheet against the wall and use an offcut to prevent the plasterboard from touch the floor.

• Make the plasterboard rest snugly against the wall in position and screw it firmly on each stud. Once done, fasten it at all the sheets’ edges and in a line down the stud to make for a firm connection. Follow the same process for the remaining plasterboard sheet till the wall is fully covered.

Fitted wardrobes are the best choice of wardrobe for most households and they’re a popular option for several homeowners for a good reason. Not only are they able to efficiently maximize your space and fit into any space no matter how awkward, but they can also be customized to fit your personal needs to feature custom lighting and many more. So if you’re planning to have one fitted but on a tight budget, you’d probably be wondering how you can install a fitted wardrobe in an alcove by yourself. This is a relatively easy task if you’re attentive to the details, however, if you’re not confident enough to pull this off, we’d advise that you get in touch with a professional who can guarantee the best results for help.

To construct a fitted wardrobe in an alcove, simply follow these steps:

✓ Take a measurement of the available space including the length, breadth and width.

✓ Sketch out what you want the wardrobe to look like while also staying within the measurements. Here, you’ll have to be particular about everything like the drawers, shelves etc.

✓ Build the frames upon which every other construction would be made.

✓ Attach the frames to the wall and floor. Make use of a hammer drill with a masonry bit to drill the holes if its a concrete floor.

✓ At this stage, you’ll have to start building your shelves in accordance to the number you’ll need.

✓ Based on the design in step 2 above, you’ll have to add the door at this stage. This is however optional as some homeowners prefer door-less wardrobes.

✓ The final step is to paint the the finished wardrobe to your taste with your choice of colour.

Planning permission is not normally needed for a loft conversion as they are covered by permitted development rights. A conversion company will tell you if you do and help you with this. For more information, see our article about planning permission.

A barn conversion can be a great investment for lots of reasons. When done well, barn conversions can be great at holding their value, meaning you could sell yours for a great price. They can also look fantastic, often with period features coupled with large areas of glazing. This can make them a great place to live, especially if you enjoy being in the countryside.

However, barn conversions do have their disadvantages. They may require extensive renovation work to bring their energy efficiency levels up to standard, which can be very expensive. It’s also important to be aware of their location – they might be on a working farm or close to several other converted buildings.

It’s essential to get a survey conducted before you buy a barn you plan to convert. This can tell you about any structural problems it might have and give you an indication of whether you might be able to get permission to convert it. You can also buy barns with planning permission already in place.

Are you interested in extending your home to create more living space? If yes, then you’d probably want to know how much value it can add to your property in order to compare the building costs to the potential value gain. Well, as long as you know what you’re doing, your house doesn’t necessarily have to be a money pit. So what are your options when talking about home extensions and what’s the associated value to be gained?

• Bathroom Extensions

Although you should have it in mind that bathroom extensions isn’t usually that cheap, but once done, it can increase the value of a standard UK house within the range of £12,000 to £15,000. Meanwhile the finishing cost of a bathroom can range from £2,500 to £7,000.

• Single or Double Storey Extensions

Single storey extensions are always huge when it comes to increasing the value of your home - giving about 4 to 7 percent increase. If it goes that far, then literally nothing beats a full spectrum, double storey extension which can give up to 11 percent increase in the value of a property - equalling about a whooping £33,000 for a standard home in the UK.

• Conservatory Extension

With conservatories becoming more and more popular in the UK due to the weather conditions, several buyers are now including it’s availability as part of the criteria for purchasing a house. Wonder why? This is simply because everyone wants to enjoy their garden all throughout the year. As a result of this high demand, adding this type of extension to your house can go a long way to increase it’s value. However, it’s very important to incorporate high quality materials during construction. With glass conservatories offering, on the average, up to £5,000 increase in value, the cheaper PVC alternative offers much less value and can also deter potential buyers.

Do you know about 25 percent of heat that escapes from an uninsulated house are lost through the roof? Fortunately, roof insulation is something that can done by all DIYers irrespective of their experience levels. However, if you happen to lack the confidence necessary to pull off this, then it’s strongly recommended that you hire the services of a professional who can guarantee the best results and also save you time and money that could arise from potential cost mistakes. Let’s take a look!

• Clear out all clutter. This involves taking out all the rubbish and clutter from the loft. In order to work effectively, you’ll need a totally clear and empty loft space.
• Ensure that there’s sufficient insulation. The importance of a good ventilation cannot be overstated. Poor ventilation will result in forming of condensation and this condensation can make the roof timbers rot and compromise the structural integrity of the entire roof. If there are no roof windows which is the easiest way to provide a loft ventilation, the next best option would be to follow the loft floor along to the point where the roof comes down to meet it. There should be a gap at this point, also referred to as the eaves, between the outside wall and the underside of the roof.
• Measure your loft area. Take a measurement of the loft space in order to calculate the amount of insulation as well as the type you need. If you’re not sure, always get more that it’s required as skimming on the amount you use will only back fire in form of increased energy costs
• Check for water pipes.

To get started, simply make sure all cracks and gaps in the ceiling are filled using a standard filler or decorator caulk. Once done, clean the gaps in the joists and even to the point of hovering all the dust up. Finally,check for the hazards that can cause you problems before laying the loft insulation.