Find an Electrician you can trust near you.

Can You Replace A Gas Boiler With An Electric Boiler?

In the UK, there are about 22 million households that are heated with the use of a gas boiler. However, do not assume that they’re the best type of boiler to install. The fact is, if your house isn’t connected to the main gas supply, the best option is for you to install an electric boiler rather than a gas boiler. So is it possible to replace a gas boiler with an electric boiler? The simple answer is yes. Both heating system options work in varying ways and also with a different impact on the environment.

The gas boiler is able to generate heat with the help of a gas burner. A heat exchanger is linked to the burner and heats the water available in its chamber. The hot water is then supplied to the heating circuit.

However, the thing is that natural gas can actually be more affordable when compared to using electricity to operate your boiler, but they have a negative impact on the environment. This is because gas boilers make use of an odourless, colourless and poisonous gas - carbon monoxide.

Meanwhile electric boilers are powered by electrical energy, hence, no carbon monoxide leak risks. Instead of using gas to heat up water, electric boilers distribute energy to heating elements which, in turn, heats up the water. So thinking about what’s best for the environment, you’d go for electric boilers. However, they’re more costly and are not as efficient as oil boilers.

If you reside in a smaller house that’s not connected to the main gas supply, then you might want to consider installing an electric boiler. However, if you live in a larger house, an electric boiler may not be the best option as they’re mostly designed to generate little quantity of hot water.

How Much To Install Solar Panels And Battery?

Are you thinking about installing solar panels and battery in your home and wondering how much the installation is going to cost? Well, you’re not alone. This is one of the most commonly asked questions in the solar world, but unfortunately a precise answer can not be provided. This is mainly due to the fact that solar panel systems come in varying sizes which is the main influencing factor that determines how much electricity that can be generated. In other words, the larger the system, the more the electricity that’ll be produced to your home’s benefit.

Generally, for a solar system size of 1kW, the average cost of the solar panel ranges between £1800 to £1850, 2kW is between £3600 to £3700, solar panel size of 3kW ranges between £5500 to £5600 and finally, 4kW is between £6000 to £6050. For example, with the aforementioned prices in mind, the cost of solar panels for a standard 3 bedroom house will range between £5520 to £6040 as the high electricity demands will need the installation of 3 to 4kW solar system size.

Meanwhile the installation cost of solar batteries is also dependent on a number of influencing factors like the size as well as the make of the battery. Generally, you can expect to spend within the range of £500 to £2000 to install your batteries depending on aforementioned factors. In the event whereby you’ll be retrofitting, you might also need to include an additional cost of £1000 for an inverter. However, it’s important to note that there are only quite a few hybrid systems which are able to combine a battery storage with an inverter.

If you’re a home or property owner planning to get an electric vehicle, having a Level 2 charger installed in your garage or near your driveway can go a long way to make charging really convenient for you. So if at all you want to take on this task by yourself, you should ensure to do it the right way. If you lack the confidence or skills required to pull this off, then we’d strongly recommend you hire the services of a professional who can guarantee the best results the first time. In this post, we’re going to provide you with an good insight on the home electric charger installation process. Let’s take a look!

• Determine the eligibility of your home. Make sure your home is eligible for a charger installation by consulting with your Technical Safety BC.
• Confirm you have sufficient electricity supply. Is there enough electricity distributed to your home to support an ev charger?
• Confirm that your electrical panel has enough space to accommodate a circuit breaker for the electric vehicle charger. If not, you’ll need to hire the services of an electrician.
• Get an electrical permit. Apply for an electrical permit with your municipality or Technical Safety BC.
• Charger installation. Proceed to fit the ev charger, but make sure a safety officer is on hand to examine your electrical work before you conceal any wiring or attach to a supply source. Then your electrician will have to complete the contractor consultancy form once the installation is done.
• Inspection. The inspection should be inspected by your municipality or Technical Safety BC.
• Apply for a rebate.

Are Electric Radiators Expensive To Run?

Just like many home additions, the running costs of electric radiators varies largely on a number of factors. Great number of electric radiators typically comes with an in built thermostat which is designed to turn itself off automatically when not in use in order to save energy.

However the energy provider’s set electricity charge tariff will also have a great influence on an electric radiator’s running cost. Let’s take a look at the running costs of an electric radiator!

A 600 Watt electric radiator ( on a standard electricity tariff) will usually have a running cost ranging between 4 to 6 pence each hour. However you should also take note that this scenario might change in situations whereby the electric radiator is not calling for heat the full 60 minutes of each hour. And this is more likely to be the situation as the thermostat is programmed in such a way that enables it to turn itself off immediately there’s an achievement of your required room temperature level - usually within 10 minutes from the time it was switched on. As a result of this, the running cost per hour of electric radiators will be greatly reduced to just about 1 to 2 pence.

It’s also important to note that enhancing the insulation of your home can go a long way to add to the heat retention value of each room. Consequently, the duration at which the electric radiator calls more heating will be significantly reduced, which in turn, implies a lower electricity bill.

Another key factor that can play a huge role in saving on your heating bills is the programming as well as usage of your electric radiators. Every radiator comes with an independent digital thermostat with a number of 24/7 programming options to help achieve maximum efficiency. When the radiator is properly set according to your lifestyle, you can save as much as 50 percent on your heating bills.

Most domestic solar thermal panels do not need planning permission and are covered by permitted development rights. There are restrictions on the size and location of these systems. If you live in a conservation area or listed building, or want to install a very large solar thermal system, check with your local authority to see if you will need planning permission.

Periodic testing and inspections should be completed: Every 10 years for your home, Every five years for rented accommodation, Every three years for a caravan, Every year for a swimming pool.Electrical inspections are also carried out when buying, selling or renting a property.

Most people want to connect solar panels to a battery when they’re not at home all day to use the electricity they generate, or generate more than they consume over a day. Solar batteries are a great way to maximise the savings on your energy bills since you can use every unit of electricity you generate.

If you want to connect your solar panels to a battery, the best – and safest – way is to ask an MCS-registered company to do it for you. They’ve had lots of training and hold qualifications in handling electricity and installing solar batteries, so they will be able to recommend the best battery for your solar panels and for the among of electricity you use. Some of the brands they might recommend include Tesla, SolarEdge and SolaX, but there are many more to choose from. If you want to send electricity to the grid from your battery to receive Smart Export Guarantee (SEG) payments, it’s also worth leaving installation up to a registered installer. This is because you might not be eligible for payments if your battery wasn’t installed by an MCS-registered company.

However, if you do want to have a go at connecting your solar panels to a battery, it’s worth finding out whether your system is ‘storage ready’. Most relatively new systems will be, since batteries are becoming more commonplace. If your solar panels are storage ready, they will have an inverter that can easily have a battery added to it. If this is the case, then you should be able to buy the solar battery you want and follow the manufacturer's instructions to install it.

But it’s worth remembering that electricity is extremely dangerous when handled improperly. If you don’t get the solar battery connected properly and something goes wrong, it could cause a fire or you could electrocute yourself. If a fire breaks out due to your battery, it’s unlikely that your home insurance company would pay out since you connected the battery yourself. That’s why it’s always worth speaking to a registered installer to install a solar battery storage system for you.

Unlike in houses built in the 1970s where a good majority of the houses will not need to be rewired, for houses built in the 1960s you’d probably need to rewire the entire house unless the wiring is the modern PVCu coated type. Generally, the homes built especially in the 1960s and 1970s brought about enormous changes. This is because over the years our way of living began to change and as a result, our need for electricity became even greater. In response to this, the electrical systems we incorporate needed to change in order to match the new set standards.

In the 1960s, the amperage normally used was increased to 100, which enables home and property owners to power their dishwasher, microwave as well as refrigerator all on one circuit. However, while this may be a remarkable improvement for our grand parents, this is just enough to cater for our modern day appliances. In recent times, new homes are constructed using a wide range of dedicated circuits due to the fact that each of our appliances makes use of much more electricity to function. Consequently because the 100 amp panels of the 1960s possessed restricted space for breakers, home and property owners who still had the units in their homes will inevitably require a sub panel or a new panel entirely - meaning a total rewiring of their property.

Furthermore in the 1960s, builders turned to aluminium from the previously used copper as it was a great conductor and also happens to be relatively cheap. However, after a couple of years a host of electrical fires cropped up in houses that are wired using aluminium. It was later discovered that when the switch to aluminium was made, the light switches or receptacles which were originally made for the previously used copper was overlooked. It was learned that there’s a corrosive chemical reaction that arises as a result of the two dissimilar metals when connected. Hence, the more reason why aluminium wired houses in the 1960s needs to be rewired.