Find a Window Installer you can trust in South Glamorgan.

No matter how big or small a building is, it can only be as good as it’s foundation - and that’s a fact! It all starts from the footing and when it isn’t deep enough, unlike badly installed gutters or gapped hardwood flooring, can make the whole building collapse to the ground. Just like any code recommendations, the depth of the footings of your porch is a parameter that must be complied with and adjusted to suit your local code requirements.

As a rule of thumb, you should always dig below the frost line when excavating your footings. At this depth level, the moisture present in the soil will be frozen. Ultimately, this will help the ground to act as a barrier to insulate the soil below the footing from freezing during the cold months. As a result, in regions where the weather is almost always very cold the depth of your footings is expected to be at least 48 inches. But in areas featuring a warm climate, you may be allowed to install your footings on grade.

In addition, it’s compulsory that your footings must be installed at a minimum depth of 12 inches below unsettled soil. However, if you’re constructing the structure into a steep hill’s side or by the side of a retaining wall, it’s required that you maintain the least distance to grade both vertically and laterally. In the event whereby you need to achieve a good lateral barrier, you’ll need to have your foundation dug a lot deeper compared to if it’s on a flat surface. For a more accurate and updated information, you can consult your local building inspection department to get familiar with the requirements in your area.

A porch is a small and low structure (with a roof) located at the main entrance of a building or house. It’s typically without a window (although newer variations may come with one) and can either be screened-in or enclosed to prevent unwanted access from insects and extremes in weather. In addition, some homes may have a three-season porch or sun porch. This may be situated by the side of the house and covered by the roof overhang - they’re usually screened in to offer good access all year round.

Generally, porches serve a wide range of purposes. They include:

• Provision of an outdoor living space to relax during the summer months

• It’s an informal extension of the the living room.

• It serves as a great place for social gatherings especially in small towns.

• You can take off your dirty shoes and dry a dripping wet dog before entering into your living room.

• It can be incorporated for relaxation purposes and watching street activities.

• It can serve as a reception area for guests.

• It can also be used for outdoor storage.

Pros & Cons Of A Porch

Pros

• Due to the fact that they’re covered, porches may require little maintenance practices.

• It can go a long way to improves the curb appeal of your property.

• It protects against the extremes of the weather.

• It can be constructed using a wide range of materials.

Cons

• It does not improve the use of the property

• It can be quite expensive to install depending of the material required as well as size of the porch.

• It does not add to the value of the home unlike several other home improvement projects

• It may not be safe to be used by a child or pet.

uPVC is unplasticised polyvinyl chloride. It is a favourite amongst homeowners and manufacturers for its cheap production cost and excellent benefits. uPVC is used for window frames, conservatories and doors. In fact, uPVC can be three times cheaper than wooden frames and is also the most energy efficient option.As well as this, uPVC is now available in a range of colours other than the typically seen bright white finish. It can also be recycled, is durable and resistant to changing weather conditions.

Ultimately the double glazing company you use is responsible for the quality of work and to ensure your windows are of an excellent standard. This is why it’s important to get a warranty and use a Fensa registered installer. If problems emerge within a couple of years then it’s likely the installation was of a poor standard.Contact the double glazing company and have the issue repaired or new windows replaced. This doesn’t matter if you received a discount of free windows as part of the deal. As long as you entered into a contract the company is obliged to restore the windows.

Did you just purchase a double glazed window and confused about how to have it installed? Fitting the window yourself can be quite easy with the help of this step by step guide. However, if you lack proper training or experience, we’d recommend you reach out to a trustworthy professional who can guarantee the best results for help. That said, now let’s take a look at the process.

• Remove the old windows by detaching the old beading and glass window safely. Then make some interval cuts using a hand saw before using a crowbar to pry it out.

• Cut the external double glazed window seal. Once done, take a measurement of the window area’s width once empty. Then transfer the measurement to the window sil to face outside and cut using a handsaw.

• Seal the window sil. Add a bead of clear silicone along both inside lip as well as the centre to seal the sil.

• Screw the double glazed window to the sil. Position the window on the top of the lipped section that was siliconed. Then pre-drill them together and screw in three places. You should make sure the screws do not go totally to the sil’s bottom.

• Install the double glazed window. After successfully screwing the double glazed window to the sil, you can now fit in the double glazing. Make use of packers to make sure it’s even in the slot.

• Screw the uPVC window to the wall. If you’re happy and satisfied with the position of the window, you can then pre-drill through the frame of the window and the brick wall. Once done, simply screw it in place using masonry screws or Spax screw as they do not require crawl plugs in bricks.

• Seal around the window. To do this, simply fill any gaps with expanding foam, wipe out the excess and seal with silicone.

Are you about to purchase a double glazed unit and wondering how to go about the replacement project? If yes, then you’re at the right place. Firstly, it’s advisable to hire the services of a reliable professional who can guarantee the best results for help especially if you lack proper training and experience in the field. However, we’ve put together this step by step guide to provide you with a detailed information about the double glazed unit replacement process. Let’s get started!

The tools and materials you require for the project includes tape measure, hammers, nail punch, scraper, spacing blocks, non-hardening butyl putty, high-security glazing tape rolls and beading tacks.

• Work out the glass size required. Simply use the tape measure to measure from frame edge to frame edge while also taking note of the thickness.

• When about to order, inform the glass merchant that the measurement provided are frame-tight. This will make him reduce the dimension a little bit, mostly by 5mm for clearance.

• Remove the beading and ensure to support the glass while doing so. If the glass units are fitted in wooden windows, you may need to cut the putty-based compound they’re normally sealed with to remove the glass.

• Lay out the beading in the window’s shape to make for easier refitting later on.

• If you’re working on wooden frames, wipe out all traces of excess installation compound using a scraper and clean the rebate with a soft brush.

• Trial fit the double glazed windows to ensure they’d slide into the frame without being forced.

• Plastic frame windows are usually in between a pair of gaskets, you should replace this with a hight security glazing tape. While for a wooden frame, simply apply strips of flexible non-setting butyl putty or high-security glazing tape on either sides of the glass.

• Install and centralize the glass in the frame.

• Press the nail wooden beading or plastic beading back into place.

A front porch is a glorious addition that would be a blessing to have in any home. It gives you a good floor space to enjoy your neighbourhood as well as your surroundings in the cool atmosphere of the outside living space. The question however is, how do you build a porch? Constructing the structure can be a very challenging task but with proper guidance and lots of practice, you can also be a skilled porch builder. To protect your investment, it’s advisable to hire the services of a professional for help with your porch especially if you lack proper training and experience. This way, you’ll get to save time and money. This guide is prepared to give you some insight into the porch building process.

lAssess Your Location

• Consider the location before proceeding with the project. It’s essential to select a location that’ll reduce the sunlight coming in.

lPlan The Materials Required For Your Porch

• You’ll have to decide the type of porch you’ll be going for. For example, your porch can be built out of wood, composite decking or if it’s going to utilize some stone flooring, brick or even tile.

lBuild Your Porch Foundation

• Dig the foundations deep to ensure stability while also putting in mind any pipework or cabling

• Fit a damp proof course

• Add the subfloor - this can be concrete or timber

lStart To Lay The Brick And Floor

• Lay the bricks evenly up to the DPC level

• Lay the floor

• Add the flooring protection

• Once done, you can lay the bricks to the window level

• You can fit in a window sill if required before proceeding the brick and block work until it reaches the roof timber’s height

• Fit the linter when you get to the top of where the window will reach.

lConstruct The Roof

• Build a timber framework

• Fit a breathable roof membrane

• Install the roof battens and lay the roof tiles.

• Add gutters

After fitting your new windows, your installer should take away and dispose of your old windows. If you want to keep them, just let your installer know before they start work. The UPVC frames are melted down and used on the unseen parts of new windows. Aluminium frames are re-smelted and wooden are broken down and used as chipboard.