Find a Window Installer you can trust in Highbridge.

Removing a double glazed window can be quite labour intensive. If you decide to try it yourself, make sure you give yourself plenty of time, and wear gloves and goggles.

Begin by unscrewing all opening windows at the hinges and removing them. Then take away the beading and putty around any fixed panes and take them out too.

Once you’ve removed all the glass, use a saw to put angled cuts in the frame, and a bar and hammer to remove it in sections. You should remove the sill if you’re going to replace that too.

Finally, cut through any screws holding the frame into place with a hacksaw.

It depends on a few factors whether a new double glazed window will look different to existing ones. If your existing windows are very old, perhaps 10 years or more, then it’s likely that there will be some small differences.

The first thing to remember is that your double glazing is exposed to the elements as soon as it’s installed. So over time, unless you’re very good at cleaning and maintaining your windows, they’re likely to look a bit dirty. Window frames that are south-facing may also become slightly discoloured from the sun, so if you install a new window right next to it you might notice a difference.

Also, there have been lots of technical advances in windows over the years. If your existing windows are significantly older, you might notice a difference in the handles on openers, and if your existing windows were installed before 2010 they might not have trickle vents, which is an extra strip on the inside of your window to keep air flowing through your home. While it’s not a legal requirement for replacement windows to have trickle vents if the original one didn’t, it’s a good idea to have them installed as they help prevent condensation and mould.

The only truly noticeably different elements to a new double glazed window compared with existing ones are likely to be on the inside, which might not be a problem for you if you only have one window in a room. However, if you know the brand of your existing windows, you can ask your window installer if they can source the same ones. Even if they’ve been updated slightly, the difference should be minimal.

No matter how big or small a building is, it can only be as good as it’s foundation - and that’s a fact! It all starts from the footing and when it isn’t deep enough, unlike badly installed gutters or gapped hardwood flooring, can make the whole building collapse to the ground. Just like any code recommendations, the depth of the footings of your porch is a parameter that must be complied with and adjusted to suit your local code requirements.

As a rule of thumb, you should always dig below the frost line when excavating your footings. At this depth level, the moisture present in the soil will be frozen. Ultimately, this will help the ground to act as a barrier to insulate the soil below the footing from freezing during the cold months. As a result, in regions where the weather is almost always very cold the depth of your footings is expected to be at least 48 inches. But in areas featuring a warm climate, you may be allowed to install your footings on grade.

In addition, it’s compulsory that your footings must be installed at a minimum depth of 12 inches below unsettled soil. However, if you’re constructing the structure into a steep hill’s side or by the side of a retaining wall, it’s required that you maintain the least distance to grade both vertically and laterally. In the event whereby you need to achieve a good lateral barrier, you’ll need to have your foundation dug a lot deeper compared to if it’s on a flat surface. For a more accurate and updated information, you can consult your local building inspection department to get familiar with the requirements in your area.

Aluminium windows have a range of benefits that make them a great alternative to uPVC windows. Developments in technology have meant that modern aluminium windows now have the same energy efficiency levels as uPVC. Plus, their strength and flexibility make them a more attractive choice to many homeowners, particularly for more modern buildings.

Aluminium frames are typically much thinner than uPVC frames, allowing more light in and wider views. The metal can also be moulded to suit custom shapes, making it ideal for unusually shaped windows. Aluminium windows are available in lots of different colours, so can be designed to suit a wide range of interiors and exteriors.

You don’t have to, especially if you’re on a budget. If you’re only replacing some, it’s a good idea to get all the windows on one side of your property replaced at the same time, so they all look the same. Be aware, obviously, huge savings could be had by having a number of windows replaced at the same time.

If you’ve got a problem with condensation and don’t have double glazing, you should find that getting new windows will help. Condensation is caused by warm air meeting a cold surface which then turns into water droplets. With two panes of glass, less heat will escape from your home and keep the window warmer, meaning when steam from the bathroom or kitchen touches your windows there should be less condensation.

Using a Fensa registered installer isn’t compulsory but it helps to protect you from cowboys and rogue traders. It will also make life a whole lot easier in regards to Building Regulations. Replacement windows must meet a certain energy efficiency rating and once fitted you need a certificate to show your installation complies. By using a Fensa registered company they’ll issue this certificate, otherwise you’ll need the council to look at the new windows.

• Washing up liquid
• Glass cleaner
• A lint-free cloth or rag
• A putty knife
• A paper plate
• Acetone