Find a Window Installer you can trust in Balerno.

1. Using a rubber mallet and a strong pallet knife, remove the beading around the window. You might think they’re part of the frame, but they’re actually separate on the inside of the frame and can be taken out by using pallet knife to prize them out. Start with one of the longest beads first and leave the top bead until last.
2. Give the glass a little tap to loosen it if it doesn’t come out straight away, then the whole unit should slide out easily. Just make sure it falls towards you and not back out onto the ground below!
3. Clear any debris that has found its way into the frame with a brush. Add spacers at the bottom of the frame – these could be pieces of plastic.
4. Get your new sealed unit (make sure you measure the glass before you buy one so you know which size to get) and carefully take it out of the packaging. Look for the British Standard mark – that shows you the bottom of the glass.
5. Lift the glass into the frame, starting with the bottom first, and make sure that it fits square in the frame before taking the spacers out.
6. Use a little washing up liquid to spread along the beads to make it easier when you slide them back into the frame. If they simply push and clip back in, you can use something like a block of wood to help you push them in correctly. Put them back in reverse order to how you took them out.

Double glazing is made up of two layers of glass, with a layer of argon gas in between. This type of glass can be used in Aluminium windows. The gas is a poor insulator, helping heat to stay in your home and making your windows more efficient. As well as trapping the argon gas, the second layer of glass reduces the amount of noise that enters your property, and helps to make your windows stronger and more secure.

No matter how big or small a building is, it can only be as good as it’s foundation - and that’s a fact! It all starts from the footing and when it isn’t deep enough, unlike badly installed gutters or gapped hardwood flooring, can make the whole building collapse to the ground. Just like any code recommendations, the depth of the footings of your porch is a parameter that must be complied with and adjusted to suit your local code requirements.

As a rule of thumb, you should always dig below the frost line when excavating your footings. At this depth level, the moisture present in the soil will be frozen. Ultimately, this will help the ground to act as a barrier to insulate the soil below the footing from freezing during the cold months. As a result, in regions where the weather is almost always very cold the depth of your footings is expected to be at least 48 inches. But in areas featuring a warm climate, you may be allowed to install your footings on grade.

In addition, it’s compulsory that your footings must be installed at a minimum depth of 12 inches below unsettled soil. However, if you’re constructing the structure into a steep hill’s side or by the side of a retaining wall, it’s required that you maintain the least distance to grade both vertically and laterally. In the event whereby you need to achieve a good lateral barrier, you’ll need to have your foundation dug a lot deeper compared to if it’s on a flat surface. For a more accurate and updated information, you can consult your local building inspection department to get familiar with the requirements in your area.

On the grand scale of things there isn’t a huge difference between B-rated windows and A-rated windows. Consumer watchdog Which? have calculated an extra 6.5% would be saved on energy bills with A rather than B rated panes. Be aware that A rated windows are slightly more expensive, however.

Some properties are unable to have double glazing, especially those in conservation areas or listed buildings. To counter this problem and still benefit from a warmer home and cheaper bills, secondary glazing is an option. Secondary glazing is a second pane fitted inside your original window. Secondary glazing will still save you around £105 yearly.

Double glazing frames don’t just have to come in uPVC and are available in other materials including aluminium and wood too. Wooden or timber windows are more suited to properties with a traditional look and are often the frame of choice for listed buildings and homes in conservation areas. When properly maintained wooden windows can last well for years but can be up to three times more expensive than uPVC.Aluminium is the strongest and most durable option. As a metal it is highly resistant to the UK’s changing weather conditions and won’t rust, warp, crack or peel. Aluminium offers a modern appeal and is available in a range of colours.

• Climate - If your window faces south, it will be subject to direct sunlight for a lot of the day. This tends to cause the sealed unit to fail more quickly – a south-facing window may last between 10-25 years. This is because the spacer bars will twist as the temperature rises and causes the adhesive holding them together to eventually fail.
• Moisture - Windows in kitchens and bathrooms tend to fail more quickly because they come into contact with moisture more often. For example, if water gets on your windowsill when you shower, the seal around the glass will come loose more quickly if it’s constantly wet.