Find a Window Installer you can trust in London.

• Thick gloves
• A hammer
• A broom
• A vacuum cleaner
• Thick-soled shoes
• Safety goggles

1. Put your gloves on and use the hammer to remove the rest of the glass. Make sure you hit the glass away from you.
2. Using the broom, sweep away any loose glass from the area, making sure you do both inside and outside.
3. Use your vacuum cleaner to remove any small pieces of glass that you might not have been able to see.

Just like every other thing in your house, your double glazed windows have an expected lifespan attached to it as it gradually becomes less functional and less efficient over time. Although there are actually top quality windows which are able to last a very long time, but the fact still remains that nothing can stand the test of time or last forever. Even the best quality double glazed windows will eventually need to be replaced at some point. So exactly how long do double glazing windows last before need a replacement?

To make it brief, most double glazing window units are typically expected to last an average of 20 years. This number of years can, however, vary within the range of 10 to 35 years based on the several factors such as the type, quality of materials as well as installation and where the windows are located.

The reason for the depreciation in double glazing windows is, over time, the windows may be subjected to some wear, tear as well as all kinds of minor damages which includes gas filled insulated glazing unit slowly and gradually leaking. According to the Centre for Sustainable Energy, the evaporation of 25 percent of gas will ultimately minimize the windows’ thermal performance. And when this occurs, fitting a secondary glazing measure or replacing the windows should be put into consideration.

Another factor leading to the gradual depreciation in double glazing windows over time has to do with condensation. When the window collects between the layers of glass due to the failure of the seal of the perimeter and the saturation of the desiccant, can only be solved by IGU replacement.

And finally, the ravages of time also has a way of taking its toll on double glazing windows. This can happen in so many ways such that the window becomes a lot less efficient and later needing to be replaced.

The energy efficiency of windows is measured using ratings, varying from A, the most efficient, to G, the least efficient. This scheme is run by the British Fenestration Council (BFRC). To comply with Building Regulations you’ll need windows of energy efficiency at least level C.

Double glazing frames don’t just have to come in uPVC and are available in other materials including aluminium and wood too. Wooden or timber windows are more suited to properties with a traditional look and are often the frame of choice for listed buildings and homes in conservation areas. When properly maintained wooden windows can last well for years but can be up to three times more expensive than uPVC.Aluminium is the strongest and most durable option. As a metal it is highly resistant to the UK’s changing weather conditions and won’t rust, warp, crack or peel. Aluminium offers a modern appeal and is available in a range of colours.

Tiling a porch roof is a very important but laborious and difficult task. A project of this magnitude will require a large investment in planning and preparation way before the actual installation process takes place. It can be a brand new porch roofing tile or a replacement of the existing one, either way it’s crucial to get the right technique. If you lack proper training or experience in this field, we’d recommend you hire the services of a reliable professional probably within your local area to guarantee the best results and to save yourself some time and money. This guide will give you a good insight into the porch roof tiling process. Let’s have a look!

• With the crown looking upwards, put the first tile on the batten and centre the tile from side to side.

• Hammer a 10d nail at the base of the tile and into the batten (make sure not to overdrive the nail).

• To provide a much needed support, apply a little mortar under the first tile.

• Identify the inner end of the first tile and place another tile on top. Take a measurement from the outer end and adjust the end of the second tile to fit.

• Just like you’ve done with the first tile, nail the second tile into the batten.

• Position two tiles at the both ends of the ridge and proceed with the installation just as you’ve done with the previous tiles.

• Take a measurement of the distance across the ridge from the first tile’s outer end. Once done, you can then calculate the number of tiles required by subtracting 16 inches from your measurement and divide the answer by 8.

• Beginning at the second tile on one end of the ridge, install the half the number of ridge tiles towards the centre of the ridge. Now install the remaining tiles working from the opposite end to the ridge’s centre. At the centre of ridge should be a key tile with mortar.

You don’t have to, especially if you’re on a budget. If you’re only replacing some, it’s a good idea to get all the windows on one side of your property replaced at the same time, so they all look the same. Be aware, obviously, huge savings could be had by having a number of windows replaced at the same time.

No matter how big or small a building is, it can only be as good as it’s foundation - and that’s a fact! It all starts from the footing and when it isn’t deep enough, unlike badly installed gutters or gapped hardwood flooring, can make the whole building collapse to the ground. Just like any code recommendations, the depth of the footings of your porch is a parameter that must be complied with and adjusted to suit your local code requirements.

As a rule of thumb, you should always dig below the frost line when excavating your footings. At this depth level, the moisture present in the soil will be frozen. Ultimately, this will help the ground to act as a barrier to insulate the soil below the footing from freezing during the cold months. As a result, in regions where the weather is almost always very cold the depth of your footings is expected to be at least 48 inches. But in areas featuring a warm climate, you may be allowed to install your footings on grade.

In addition, it’s compulsory that your footings must be installed at a minimum depth of 12 inches below unsettled soil. However, if you’re constructing the structure into a steep hill’s side or by the side of a retaining wall, it’s required that you maintain the least distance to grade both vertically and laterally. In the event whereby you need to achieve a good lateral barrier, you’ll need to have your foundation dug a lot deeper compared to if it’s on a flat surface. For a more accurate and updated information, you can consult your local building inspection department to get familiar with the requirements in your area.