Find a Window Installer you can trust in Swanscombe.

Did you just purchase a double glazed window and confused about how to have it installed? Fitting the window yourself can be quite easy with the help of this step by step guide. However, if you lack proper training or experience, we’d recommend you reach out to a trustworthy professional who can guarantee the best results for help. That said, now let’s take a look at the process.

• Remove the old windows by detaching the old beading and glass window safely. Then make some interval cuts using a hand saw before using a crowbar to pry it out.

• Cut the external double glazed window seal. Once done, take a measurement of the window area’s width once empty. Then transfer the measurement to the window sil to face outside and cut using a handsaw.

• Seal the window sil. Add a bead of clear silicone along both inside lip as well as the centre to seal the sil.

• Screw the double glazed window to the sil. Position the window on the top of the lipped section that was siliconed. Then pre-drill them together and screw in three places. You should make sure the screws do not go totally to the sil’s bottom.

• Install the double glazed window. After successfully screwing the double glazed window to the sil, you can now fit in the double glazing. Make use of packers to make sure it’s even in the slot.

• Screw the uPVC window to the wall. If you’re happy and satisfied with the position of the window, you can then pre-drill through the frame of the window and the brick wall. Once done, simply screw it in place using masonry screws or Spax screw as they do not require crawl plugs in bricks.

• Seal around the window. To do this, simply fill any gaps with expanding foam, wipe out the excess and seal with silicone.

Yes, of course! It’s common for people to replace just one double glazed window. One reason that people want to replace one window is that the sealed unit inside has failed. You’ll know if this has happened because you’ll be able to see condensation on the inside of glass, which gets frustrating because you can’t wipe it away. In this case, you can choose to simply replace the sealed unit or the entire frame, which you might want to do if it’s looking past its best.

When you’re replacing just one double glazed window, if you know the brand of your current windows you could ask your installer if they can source the same ones. This will help to keep them looking as similar as possible, although if your existing windows are very old you may notice some discolouration on the exterior compared to the new one, and locks and trickle vents might look different.

Replacing just one double glazed window shouldn’t take a qualified window fitter long, and could cost as little as £400. If you want to simply replace the sealed unit, that may only cost around £250. You could try to fit a new window yourself, but it’s worth bearing in mind that all replacement windows need to be certified that they’ve been installed to meet building regulations, so you’ll need to apply to your local building control officer who will come and inspect the work then issue a certificate. If you ask an installer who is registered with a self-certification scheme (like FENSA) to fit the window for you, they can issue the certificate themselves when they’ve finished the work.

One of the essential factors that makes a home truly a home is the convenience and comfort it provides us. As a result, we usually have a long to do list comprising things that come together to make sure our home is comfortable with ambient temperature at the very top of the scale of preference. After all, no matter how greatly designed your furniture and home decor is, it probably would amount for nothing if the temperature is either too hot or too cold. Some of the most common ways we incorporate to make the temperature a lot more conducive and warm during the winter months is by installing air conditioning system or through top notch insulation materials, but the fact still remains that a lot of heat would escape through the doors and windows. And that’s exactly the use of double glazing. So how exactly does double glazing work?

Double glazing basically works by preventing the escape of air and trapping it between two panes of glass. It’s the trapped air which serves as an insulation barrier which delivers 3 major functions. First and foremost, it stops the escape of heat through the window as the barrier created insulates the room from varying air temperatures at both sides of the glazing unit. The second major function is the double glazing works to keep down noise pollution coming from outside. While the third major function of double glazing I the fact that it helps minimize condensation which usually occurs on the single glazed windows’ inside as the cold outside air works to cool the warm air inside the house. When you install a double glazing window, the insulation barrier generated will work to stop the air temperature transmission which ultimately helps prevent the occurrence of condensation.

Fitting a Velux window into a slate roof is very similar to the way you’d install it in other roof types. All roof windows, whether a Velux-branded one or not, will come with detailed instructions for you to follow if you want to have a go at fitting it yourself. But here are some brief instructions to give you an idea of what’s involved in installing a Velux window into a slate roof:

1. After you’ve removed the Velux window from its packaging, remove the sash (the part that opens) from the frame, according to the manufacturer’s instructions.
2. Next, you need to prepare the opening for the window. You can often cut through the felt, remove one of the battens from under a slate, then slide all the slate tiles into the roof space. You should then make the cut 40-60mm wider than the window, cutting away roof timbers then replacing them with more around the opening to strengthen it.
3. The roof window’s bottom brackets need to be installed on one of the existing battens for the slate roof. One of the slate courses should line up 105mm below the top edge of the batten you use.
4. Then, measure from the top edge of the batten upwards to the height of the window plus 45mm. This is where the top installation batten should be installed, with an overhang of 100mm on each side.
5. Remove the course of slates below the window, trim any excess felt and fold it over the surrounding timber. This helps with waterproofing.
6. Add the insulation collar according to the Velux window manufacturer’s instructions.
7. Place the frame in the opening, adding the brackets according to the instructions. You’ll find that lots of roof windows have pre-drilled holes to make it easy for you.
8. Replace the sash and line up the hinges. Take a look at the opening at the bottom between the sash and the frame – it should be even along the entire width. Remove the sash again to fix the upper brackets according to instructions.
9. Add the underfelt collar for your roof window as instructed by the manufacturer, then replace any slates at the bottom. You might need to cut them to size.
10. Next, add the flashing according to the instructions, along with any parts that are not yet attached, including the hood section and top flashing piece.
11. Replace all the slates around the window, allowing 60-100mm of space between the course of slates above the window and the top of the window to allow for rainwater drainage. Then replace the sash into the frame again.
12. Add the vapour barrier on the inside of the window using the screws provided, then tape it to the existing vapour barrier to prevent moisture from reaching your roof structure.

And that’s it! If you think that sounds a bit complicated, ask a roofer or window installer to fit your roof window into a slate roof for you. You’ll get a better finish and you can be sure that you won’t get any leaks from a botched installation.

Windows, being a very crucial feature in every home, are one of the things you simply can’t afford to ignore in your home. Having a good understanding and solid knowledge of your windows’ components like the window sash will help you stay up to date with them and able to identify any minor mishaps early on before it leads to a much bigger problem. So what exactly is a window sash?

Well without much fuss, a window sash is simply that part of your windows that’s able to open and close. And there could as well be more than one window sash that’s operable depending on your window’s type. Window sash usually possess a very basic design as well as structure. What’s more? This section of a window happens to be a frame that’s designed in such a way to make for easy placement inside the whole window casement. You’ll discover inside the sash frame, the window glass alongside any framework possessed by your window which includes grids.

Usually, the sash is fitted into the frame of the window on a runners’ set in such a way that allows for both upward and downward movements. And finally, the window sash’s frame typically comes with a locking system which provided for extra safety and security.

The window sash is a vital feature that can determine the durability and overall performance of the windows. In the event whereby your window sash is malfunctioning, it can result to numerous problems which includes both drafts as well as leaks. As a result, it’s very important to keep your window sashes in a great working condition as failure to do so will make opening and closing your windows a really difficult task.

The cost for a sun tunnel is affected by 5 key factors:

1. Tube size: Small areas or stairways can gain from a 10-inch size tube, whilst bigger rooms will require a bigger tube. The higher television size, the greater the price.
2. Kind of tunnel and also roof type: You can pick from stiff or flexible tunnels and also domed or flat roofing system panels. Each choice will have a different price.
3. Place: Where you stay in the country will certainly impact the price of your sun tunnel installation. Generally, the higher the living prices in your location, the greater the price of employing an expert will certainly be.
4. Length of the tunnel: Longer tunnels will be charged at a greater price than their shorter equivalents so whether the tunnel runs from the roof to the 2nd or very first flooring will certainly impact the sun tunnel price.
5. Ease of gain access to: Flexible tubes are fantastic for homes where sun tunnels do not run in a straight line from roofing to ceiling. The tubes can then be fitted around challenges in your loft space. Frustratingly, these alternatives do not allow as much light as stiff tubes and also due to their hard setup can be much more expensive.

Velux windows, or roof windows, are very easy to clean. Regular cleaning helps to keep them looking bright and shiny for years to come. So how should you clean Velux windows?

If you want to clean the air filter, you can remove it and wash it with your normal household cleaners. Velux windows have a cleaning position, so rotate and secure it into this position then remove the filter. You should be able to buy new filters from the manufacturer of your roof window.

To clean the outer pane, there’s no need to lean out of the window and risk falling out. Simply rotate the sash (the opening part) 180 degrees and secure it into position. Then you can clean the pane with a soft, lint-free cloth, sponge or squeegee and clean water. If you live in a hard water area, add some detergent to the water and wipe the window dry when you’re finished. You can also use normal non-abrasive household cleaners.

It’s recommended that you clean the flashing around your roof window at least once a year. You can use a brush to do this. This will allow rainwater to flow freely and stop any leaves from collecting.

If you’re in any doubt about using certain cleaners on your Velux windows, get in touch with the manufacturer who should be able to help. You can also do a patch test on an inconspicuous area if you’re unsure.

Double glazing frames don’t just have to come in uPVC and are available in other materials including aluminium and wood too. Wooden or timber windows are more suited to properties with a traditional look and are often the frame of choice for listed buildings and homes in conservation areas. When properly maintained wooden windows can last well for years but can be up to three times more expensive than uPVC.Aluminium is the strongest and most durable option. As a metal it is highly resistant to the UK’s changing weather conditions and won’t rust, warp, crack or peel. Aluminium offers a modern appeal and is available in a range of colours.