Find a Window Installer you can trust in Avoch.

Using a Fensa registered installer isn’t compulsory but it helps to protect you from cowboys and rogue traders. It will also make life a whole lot easier in regards to Building Regulations. Replacement windows must meet a certain energy efficiency rating and once fitted you need a certificate to show your installation complies. By using a Fensa registered company they’ll issue this certificate, otherwise you’ll need the council to look at the new windows.

It depends on a few factors whether a new double glazed window will look different to existing ones. If your existing windows are very old, perhaps 10 years or more, then it’s likely that there will be some small differences.

The first thing to remember is that your double glazing is exposed to the elements as soon as it’s installed. So over time, unless you’re very good at cleaning and maintaining your windows, they’re likely to look a bit dirty. Window frames that are south-facing may also become slightly discoloured from the sun, so if you install a new window right next to it you might notice a difference.

Also, there have been lots of technical advances in windows over the years. If your existing windows are significantly older, you might notice a difference in the handles on openers, and if your existing windows were installed before 2010 they might not have trickle vents, which is an extra strip on the inside of your window to keep air flowing through your home. While it’s not a legal requirement for replacement windows to have trickle vents if the original one didn’t, it’s a good idea to have them installed as they help prevent condensation and mould.

The only truly noticeably different elements to a new double glazed window compared with existing ones are likely to be on the inside, which might not be a problem for you if you only have one window in a room. However, if you know the brand of your existing windows, you can ask your window installer if they can source the same ones. Even if they’ve been updated slightly, the difference should be minimal.

The energy efficiency of windows is measured using ratings, varying from A, the most efficient, to G, the least efficient. This scheme is run by the British Fenestration Council (BFRC). To comply with Building Regulations you’ll need windows of energy efficiency at least level C.

Did you just purchase a double glazed window and confused about how to have it installed? Fitting the window yourself can be quite easy with the help of this step by step guide. However, if you lack proper training or experience, we’d recommend you reach out to a trustworthy professional who can guarantee the best results for help. That said, now let’s take a look at the process.

• Remove the old windows by detaching the old beading and glass window safely. Then make some interval cuts using a hand saw before using a crowbar to pry it out.

• Cut the external double glazed window seal. Once done, take a measurement of the window area’s width once empty. Then transfer the measurement to the window sil to face outside and cut using a handsaw.

• Seal the window sil. Add a bead of clear silicone along both inside lip as well as the centre to seal the sil.

• Screw the double glazed window to the sil. Position the window on the top of the lipped section that was siliconed. Then pre-drill them together and screw in three places. You should make sure the screws do not go totally to the sil’s bottom.

• Install the double glazed window. After successfully screwing the double glazed window to the sil, you can now fit in the double glazing. Make use of packers to make sure it’s even in the slot.

• Screw the uPVC window to the wall. If you’re happy and satisfied with the position of the window, you can then pre-drill through the frame of the window and the brick wall. Once done, simply screw it in place using masonry screws or Spax screw as they do not require crawl plugs in bricks.

• Seal around the window. To do this, simply fill any gaps with expanding foam, wipe out the excess and seal with silicone.

1. Using a rubber mallet and a strong pallet knife, remove the beading around the window. You might think they’re part of the frame, but they’re actually separate on the inside of the frame and can be taken out by using pallet knife to prize them out. Start with one of the longest beads first and leave the top bead until last.
2. Give the glass a little tap to loosen it if it doesn’t come out straight away, then the whole unit should slide out easily. Just make sure it falls towards you and not back out onto the ground below!
3. Clear any debris that has found its way into the frame with a brush. Add spacers at the bottom of the frame – these could be pieces of plastic.
4. Get your new sealed unit (make sure you measure the glass before you buy one so you know which size to get) and carefully take it out of the packaging. Look for the British Standard mark – that shows you the bottom of the glass.
5. Lift the glass into the frame, starting with the bottom first, and make sure that it fits square in the frame before taking the spacers out.
6. Use a little washing up liquid to spread along the beads to make it easier when you slide them back into the frame. If they simply push and clip back in, you can use something like a block of wood to help you push them in correctly. Put them back in reverse order to how you took them out.

Whether you’re hiring a professional to replace your double glazing or are considering DIY, it’s a good idea to know how to fit a double glazed window.

You need to start by assembling your window. Fit any handles and cut the outer sill to size by measuring the outer wall depth. Then, screw the outer sill to the window frame and attach the frame fixers. Screw the ventilation grilles onto the inside of the frame and fix the vents on.

Next, you need put the window into place, using spacers to wedge it in. Use a spirit level to check it’s level horizontally and vertically, adding extra spacers if needed. Then, fix the frame into place at each fixing point using a drill, wall plugs and screws. Measure and cut the interior sill, and check that it’s level, adding spacers if needed. Then fix it using screws, masonry nails or adhesive.

Finally, fill in any wide gaps with foam filler and small gaps with sealant. You can get interior and exterior trims to cover these up, making your window look neat and professional.

By replacing the single glazed windows in your home you stand to make savings of around £170 each year. It’s not just the financial gain that makes double glazing attractive though and you can also save up to 680kg of carbon emissions annually. Over 20 years this is a saving of around £3,400 and 13,600kg of CO2.