Find a Window Installer you can trust near you.

Ultimately the double glazing company you use is responsible for the quality of work and to ensure your windows are of an excellent standard. This is why it’s important to get a warranty and use a Fensa registered installer. If problems emerge within a couple of years then it’s likely the installation was of a poor standard.Contact the double glazing company and have the issue repaired or new windows replaced. This doesn’t matter if you received a discount of free windows as part of the deal. As long as you entered into a contract the company is obliged to restore the windows.

These days, buyers expect homes to have double glazing. People recognise the benefits of installing double glazing, so if you don’t have it installed you should consider it. You’ll increase your property’s value and give it a better chance of selling faster, since single glazed properties are also more likely to have problems with damp and mould which could put buyers off.

If you’ve got a problem with condensation and don’t have double glazing, you should find that getting new windows will help. Condensation is caused by warm air meeting a cold surface which then turns into water droplets. With two panes of glass, less heat will escape from your home and keep the window warmer, meaning when steam from the bathroom or kitchen touches your windows there should be less condensation.

Whether you need toughened glass in your windows depends on where the windows are in your home or business. Toughened glass is sometimes referred to as tempered or safety glass, and it just means it’s stronger than the standard glass that’s usually offered with double glazed windows. So how do you know if you need it?

Toughened glass is useful in areas of your home where you might come into contact with the windows if you were to trip and fall. If you put your hands out to steady yourself on standard glass the chances are it would break into large sharp pieces with jagged edges. Of course, this means that you could seriously cut yourself if this were to happen. With toughened glass, the structure of the glass is changed so that if it breaks it shatters into lots of tiny pieces, minimising the risk to you if you were to fall on it.

You might want to use toughened glass in patio doors, low windows or frames next to doors. It just means that you will be safer if the unlikely happens and you or a family member falls through the glass. There are certain requirements through Building Regulations with windows at a certain level, but any reputable window installer should be able to go through these with you if you need to replace your windows with toughened glass. The regulations will only apply to new windows – there's no need to switch your windows to toughened glass early, but when you do come to replace them you’ll need to make sure they meet the standard.

• Impact from a stone or other object smashing the glass in a ‘bullseye’ effect
• The result of a break-in
• Extreme weather or changes in pressure causing a crack
• The sealed unit being ‘blown’, meaning that it’s no longer energy efficient due to air leaking out

uPVC is unplasticised polyvinyl chloride. It is a favourite amongst homeowners and manufacturers for its cheap production cost and excellent benefits. uPVC is used for window frames, conservatories and doors. In fact, uPVC can be three times cheaper than wooden frames and is also the most energy efficient option.As well as this, uPVC is now available in a range of colours other than the typically seen bright white finish. It can also be recycled, is durable and resistant to changing weather conditions.

Did you just purchase a double glazed window and confused about how to have it installed? Fitting the window yourself can be quite easy with the help of this step by step guide. However, if you lack proper training or experience, we’d recommend you reach out to a trustworthy professional who can guarantee the best results for help. That said, now let’s take a look at the process.

• Remove the old windows by detaching the old beading and glass window safely. Then make some interval cuts using a hand saw before using a crowbar to pry it out.

• Cut the external double glazed window seal. Once done, take a measurement of the window area’s width once empty. Then transfer the measurement to the window sil to face outside and cut using a handsaw.

• Seal the window sil. Add a bead of clear silicone along both inside lip as well as the centre to seal the sil.

• Screw the double glazed window to the sil. Position the window on the top of the lipped section that was siliconed. Then pre-drill them together and screw in three places. You should make sure the screws do not go totally to the sil’s bottom.

• Install the double glazed window. After successfully screwing the double glazed window to the sil, you can now fit in the double glazing. Make use of packers to make sure it’s even in the slot.

• Screw the uPVC window to the wall. If you’re happy and satisfied with the position of the window, you can then pre-drill through the frame of the window and the brick wall. Once done, simply screw it in place using masonry screws or Spax screw as they do not require crawl plugs in bricks.

• Seal around the window. To do this, simply fill any gaps with expanding foam, wipe out the excess and seal with silicone.

To install one small double glazed window, it will take anywhere between two hours and half a day. It will depend on whether one installer is fitting your window or two. And if you’re doing it yourself and don’t have any professional experience, it will take even longer.

When the window fitters arrive, they will make sure they’ve got safe access to the window and move any heavy furniture if they need to. Any good installer will lay down a dust sheet, but it’s a good idea to check that they’ve got one laid down before they start.

The first step any window installer will take is to double check the measurements of the new frame against your existing one. Hopefully it should match up, so then they’ll take the old window out. Then, they’ll insert the new frame into the aperture and bolt it into the concrete. They'll check it with a spirit level to ensure it’s even before moving onto the glass sealed unit.

The installer will place the glass into the aperture, then fit the beads to secure the glass in the frame. They’ll then use silicone and trim on the inside and outside to ensure the window looks perfect. You won’t be able to see where they’ve used sealants or trims because they’ll colour match them so it’s not noticeable. Then, they’ll tidy up all of their tools and the working area and let you know what needs to be done in terms of proving that the window meets building regulations. Most good installers are registered with a self-certification scheme, so will be able to issue a certification once the work is complete.