Find a Window Installer you can trust in Pontypool.

Fitting a Velux window into a slate roof is very similar to the way you’d install it in other roof types. All roof windows, whether a Velux-branded one or not, will come with detailed instructions for you to follow if you want to have a go at fitting it yourself. But here are some brief instructions to give you an idea of what’s involved in installing a Velux window into a slate roof:

1. After you’ve removed the Velux window from its packaging, remove the sash (the part that opens) from the frame, according to the manufacturer’s instructions.
2. Next, you need to prepare the opening for the window. You can often cut through the felt, remove one of the battens from under a slate, then slide all the slate tiles into the roof space. You should then make the cut 40-60mm wider than the window, cutting away roof timbers then replacing them with more around the opening to strengthen it.
3. The roof window’s bottom brackets need to be installed on one of the existing battens for the slate roof. One of the slate courses should line up 105mm below the top edge of the batten you use.
4. Then, measure from the top edge of the batten upwards to the height of the window plus 45mm. This is where the top installation batten should be installed, with an overhang of 100mm on each side.
5. Remove the course of slates below the window, trim any excess felt and fold it over the surrounding timber. This helps with waterproofing.
6. Add the insulation collar according to the Velux window manufacturer’s instructions.
7. Place the frame in the opening, adding the brackets according to the instructions. You’ll find that lots of roof windows have pre-drilled holes to make it easy for you.
8. Replace the sash and line up the hinges. Take a look at the opening at the bottom between the sash and the frame – it should be even along the entire width. Remove the sash again to fix the upper brackets according to instructions.
9. Add the underfelt collar for your roof window as instructed by the manufacturer, then replace any slates at the bottom. You might need to cut them to size.
10. Next, add the flashing according to the instructions, along with any parts that are not yet attached, including the hood section and top flashing piece.
11. Replace all the slates around the window, allowing 60-100mm of space between the course of slates above the window and the top of the window to allow for rainwater drainage. Then replace the sash into the frame again.
12. Add the vapour barrier on the inside of the window using the screws provided, then tape it to the existing vapour barrier to prevent moisture from reaching your roof structure.

And that’s it! If you think that sounds a bit complicated, ask a roofer or window installer to fit your roof window into a slate roof for you. You’ll get a better finish and you can be sure that you won’t get any leaks from a botched installation.

In general, no – you don’t need planning permission for a Velux window. The Planning Portal says that you don’t need to apply for planning permission to install a roof window if the following conditions are met:

• A roof window must not protrude more than 150 millimetres above the existing roof plane
No roof window or any other alteration can be higher than the highest part of the roof or stand out above the roof ridge
• Side-facing windows must have obscure glazing to protect privacy of neighbours and, if they open, they must be 1.7 metres above the floor of the room in which they are installed

You don’t need to apply for planning permission for a roof window because they are covered under permitted development rights. However, if you’re a leaseholder or you live in a building where your local authority has made an Article 4 Direction, you will have to apply. Usually, an Article 4 Direction is made when you live in a conservation area where any external home improvements could affect the character and look of the area. Luckily, there are special Velux windows that are designed to be more likely to be accepted by your local planning authority. They’re called conservation windows and, although there’s still no guarantee that they will be accepted, they are designed to look more traditional. Even if you don’t need planning permission for your roof window, you still need to follow any relevant building regulations for your local authority. The most important parts for Velux windows are section J and section L of building regulations, which refer to energy efficiency, thermal insulation and fire protection.

Just like every other thing in your house, your double glazed windows have an expected lifespan attached to it as it gradually becomes less functional and less efficient over time. Although there are actually top quality windows which are able to last a very long time, but the fact still remains that nothing can stand the test of time or last forever. Even the best quality double glazed windows will eventually need to be replaced at some point. So exactly how long do double glazing windows last before need a replacement?

To make it brief, most double glazing window units are typically expected to last an average of 20 years. This number of years can, however, vary within the range of 10 to 35 years based on the several factors such as the type, quality of materials as well as installation and where the windows are located.

The reason for the depreciation in double glazing windows is, over time, the windows may be subjected to some wear, tear as well as all kinds of minor damages which includes gas filled insulated glazing unit slowly and gradually leaking. According to the Centre for Sustainable Energy, the evaporation of 25 percent of gas will ultimately minimize the windows’ thermal performance. And when this occurs, fitting a secondary glazing measure or replacing the windows should be put into consideration.

Another factor leading to the gradual depreciation in double glazing windows over time has to do with condensation. When the window collects between the layers of glass due to the failure of the seal of the perimeter and the saturation of the desiccant, can only be solved by IGU replacement.

And finally, the ravages of time also has a way of taking its toll on double glazing windows. This can happen in so many ways such that the window becomes a lot less efficient and later needing to be replaced.

Most window installers will be able to provide you with one double glazed window and fit it for you. If you’re replacing one double glazed window in your home, ask them to try and source the same windows that you already have or find one that’s very similar. Externally, you probably won’t be able to notice the difference, but if your existing windows are very old there may be some exterior discolouration and the locks and handles might look slightly different.

If you want one double glazed window so you can fit it yourself, there are lots of online companies that can supply you with one window. However, window fitting is a skilled trade and you might want to consider whether you have the right tools and experience to fit it yourself. Of course, you’ll save money on installation costs, but if something goes wrong, you might end up shelling out to get it fixed anyway.

The other thing to consider is that any replacement windows need to be certified that they meet Building Regulations. If you fit the double glazed window yourself, you’ll need to apply to your local council building control officer to get a certificate that confirms that you fitted the window within the regulations. You’ll have to pay a fee for this, and it will be even more expensive if Building Control say that the window hasn’t been fitted within the regulations and you have to start again.

The alternative is to ask a reputable window installer that is registered with a self-certification scheme, like FENSA, to install the window. That means that they can self-certify that the window meets building regulations once they’ve finished the installation.

• Washing up liquid
• Glass cleaner
• A lint-free cloth or rag
• A putty knife
• A paper plate
• Acetone

Ultimately the double glazing company you use is responsible for the quality of work and to ensure your windows are of an excellent standard. This is why it’s important to get a warranty and use a Fensa registered installer. If problems emerge within a couple of years then it’s likely the installation was of a poor standard.Contact the double glazing company and have the issue repaired or new windows replaced. This doesn’t matter if you received a discount of free windows as part of the deal. As long as you entered into a contract the company is obliged to restore the windows.

• Thick gloves
• A hammer
• A broom
• A vacuum cleaner
• Thick-soled shoes
• Safety goggles

1. Put your gloves on and use the hammer to remove the rest of the glass. Make sure you hit the glass away from you.
2. Using the broom, sweep away any loose glass from the area, making sure you do both inside and outside.
3. Use your vacuum cleaner to remove any small pieces of glass that you might not have been able to see.