Find a Window Installer you can trust in Newnham.

• The glass has smashed from an impact such as a stone hitting it from a lawnmower
• You have been broken into and suspects used the window to gain entry
• The glass has blown (lost its airtightness) from constant water build-up around the seals, which is common in bathrooms
• Extreme weather or pressure changes have caused a crack

1. Including the beading (the plastic and rubber seals around the windows that can be removed), measure the width of the window frame.
2. Do the same for the height of the window, making sure you include the beading.
3. Then, take 10mm off each measurement, and you have the approximate size of your glass.

On the grand scale of things there isn’t a huge difference between B-rated windows and A-rated windows. Consumer watchdog Which? have calculated an extra 6.5% would be saved on energy bills with A rather than B rated panes. Be aware that A rated windows are slightly more expensive, however.

There are so many benefits that comes with building a porch in your home premises. It’s an extra space where a lot can be achieved such as drying a dripping wet dog, taking off your dirty shoes or boot and lots more. So if you’re considering to construct a porch, it’s definitely going to be a wise decision. However, before you get started, there’s a need to determine if you’ll need planning permission for a porch. It’s important to take note that planning laws are dynamic and can be updated at any point, so be sure only to use trusted sources only as your guide. If you’re the homeowner or landlord, it’s entirely your responsibility to obtain the right approval for any development project you wish to carry out within your premises.

A Porch can not be termed as an extension and neither is it a conservatory, they’re basically built to the home’s front covering the main entrance using a stone base or a brick. As a result, a porch does not need planning permission due to the fact that it’s covered by the permitted development rights if the specific guidelines for porches are complied with. Below are the instances where you WILL need planning permission for a porch.

✓ If the floor space is more than 3sqm (the wall inclusive).

✓ The highest point has a height of more than 3 metres.

✓ If the porch is situated within 2 metres of a boundary directly facing on to the road.

You may need planning permission if the house is a listed building, designated area or falls under an Article 4 Direction.

In order to build a porch without planning permission, you need to consider all the criteria stated above. You can also visit the Planning Portal website to get more detailed information before getting started.

Whether you’re hiring a professional to replace your double glazing or are considering DIY, it’s a good idea to know how to fit a double glazed window.

You need to start by assembling your window. Fit any handles and cut the outer sill to size by measuring the outer wall depth. Then, screw the outer sill to the window frame and attach the frame fixers. Screw the ventilation grilles onto the inside of the frame and fix the vents on.

Next, you need put the window into place, using spacers to wedge it in. Use a spirit level to check it’s level horizontally and vertically, adding extra spacers if needed. Then, fix the frame into place at each fixing point using a drill, wall plugs and screws. Measure and cut the interior sill, and check that it’s level, adding spacers if needed. Then fix it using screws, masonry nails or adhesive.

Finally, fill in any wide gaps with foam filler and small gaps with sealant. You can get interior and exterior trims to cover these up, making your window look neat and professional.

Did you just purchase a double glazed window and confused about how to have it installed? Fitting the window yourself can be quite easy with the help of this step by step guide. However, if you lack proper training or experience, we’d recommend you reach out to a trustworthy professional who can guarantee the best results for help. That said, now let’s take a look at the process.

• Remove the old windows by detaching the old beading and glass window safely. Then make some interval cuts using a hand saw before using a crowbar to pry it out.

• Cut the external double glazed window seal. Once done, take a measurement of the window area’s width once empty. Then transfer the measurement to the window sil to face outside and cut using a handsaw.

• Seal the window sil. Add a bead of clear silicone along both inside lip as well as the centre to seal the sil.

• Screw the double glazed window to the sil. Position the window on the top of the lipped section that was siliconed. Then pre-drill them together and screw in three places. You should make sure the screws do not go totally to the sil’s bottom.

• Install the double glazed window. After successfully screwing the double glazed window to the sil, you can now fit in the double glazing. Make use of packers to make sure it’s even in the slot.

• Screw the uPVC window to the wall. If you’re happy and satisfied with the position of the window, you can then pre-drill through the frame of the window and the brick wall. Once done, simply screw it in place using masonry screws or Spax screw as they do not require crawl plugs in bricks.

• Seal around the window. To do this, simply fill any gaps with expanding foam, wipe out the excess and seal with silicone.

Tiling a porch roof is a very important but laborious and difficult task. A project of this magnitude will require a large investment in planning and preparation way before the actual installation process takes place. It can be a brand new porch roofing tile or a replacement of the existing one, either way it’s crucial to get the right technique. If you lack proper training or experience in this field, we’d recommend you hire the services of a reliable professional probably within your local area to guarantee the best results and to save yourself some time and money. This guide will give you a good insight into the porch roof tiling process. Let’s have a look!

• With the crown looking upwards, put the first tile on the batten and centre the tile from side to side.

• Hammer a 10d nail at the base of the tile and into the batten (make sure not to overdrive the nail).

• To provide a much needed support, apply a little mortar under the first tile.

• Identify the inner end of the first tile and place another tile on top. Take a measurement from the outer end and adjust the end of the second tile to fit.

• Just like you’ve done with the first tile, nail the second tile into the batten.

• Position two tiles at the both ends of the ridge and proceed with the installation just as you’ve done with the previous tiles.

• Take a measurement of the distance across the ridge from the first tile’s outer end. Once done, you can then calculate the number of tiles required by subtracting 16 inches from your measurement and divide the answer by 8.

• Beginning at the second tile on one end of the ridge, install the half the number of ridge tiles towards the centre of the ridge. Now install the remaining tiles working from the opposite end to the ridge’s centre. At the centre of ridge should be a key tile with mortar.

Double glazed windows are one of the most popular window options for home and property owners in the United Kingdom and reasonably so. They are able to offer a wide range of benefits to home owners which includes being energy efficient, reducing the build up of condensation on windows and black mould growth, significantly reducing background noise for a better relaxation or night rest, increasing the value of your property as well as adding to the aesthetic appeal of your home. So if you’ve decided to lay your hands on a double glazed window, you’d probably also like to know how much it’s going to cost. Well, providing a simple and accurate answer to the question of double glazing window cost is almost impossible as there are so many factors that influences the price including the materials and style.

Several suppliers usually provide the list of their double glazing windows on their websites, however these prices are only for basic off the shelf window and most often without the installation cost. Furthermore, if you require some special features to your double glazed window, then this will also tell on the total cost of the window.

So how much will a double glazing window cost? The cost of a double glazing window usually ranges between £100 to £3,200 per window, depending on the available options.

To have a more accurate estimate of the cost of a double glazing window, you’ll need a obtain a survey from a double glazing installer who can take into account any possible complications that may arise when installing your windows while also giving an advise on the most suitable window style for your property.

• Thick gloves
• A hammer
• A broom
• A vacuum cleaner
• Thick-soled shoes
• Safety goggles

1. Put your gloves on and use the hammer to remove the rest of the glass. Make sure you hit the glass away from you.
2. Using the broom, sweep away any loose glass from the area, making sure you do both inside and outside.
3. Use your vacuum cleaner to remove any small pieces of glass that you might not have been able to see.