Find a Window Installer you can trust in Haddington.

By replacing the single glazed windows in your home you stand to make savings of around £170 each year. It’s not just the financial gain that makes double glazing attractive though and you can also save up to 680kg of carbon emissions annually. Over 20 years this is a saving of around £3,400 and 13,600kg of CO2.

There are so many benefits that comes with building a porch in your home premises. It’s an extra space where a lot can be achieved such as drying a dripping wet dog, taking off your dirty shoes or boot and lots more. So if you’re considering to construct a porch, it’s definitely going to be a wise decision. However, before you get started, there’s a need to determine if you’ll need planning permission for a porch. It’s important to take note that planning laws are dynamic and can be updated at any point, so be sure only to use trusted sources only as your guide. If you’re the homeowner or landlord, it’s entirely your responsibility to obtain the right approval for any development project you wish to carry out within your premises.

A Porch can not be termed as an extension and neither is it a conservatory, they’re basically built to the home’s front covering the main entrance using a stone base or a brick. As a result, a porch does not need planning permission due to the fact that it’s covered by the permitted development rights if the specific guidelines for porches are complied with. Below are the instances where you WILL need planning permission for a porch.

✓ If the floor space is more than 3sqm (the wall inclusive).

✓ The highest point has a height of more than 3 metres.

✓ If the porch is situated within 2 metres of a boundary directly facing on to the road.

You may need planning permission if the house is a listed building, designated area or falls under an Article 4 Direction.

In order to build a porch without planning permission, you need to consider all the criteria stated above. You can also visit the Planning Portal website to get more detailed information before getting started.

The energy efficiency of windows is measured using ratings, varying from A, the most efficient, to G, the least efficient. This scheme is run by the British Fenestration Council (BFRC). To comply with Building Regulations you’ll need windows of energy efficiency at least level C.

The energy efficiency of windows is measured using ratings, varying from A, the most efficient, to G, the least efficient. This scheme is run by the British Fenestration Council (BFRC). To comply with Building Regulations you’ll need windows of energy efficiency at least level C.

Did you just purchase a double glazed window and confused about how to have it installed? Fitting the window yourself can be quite easy with the help of this step by step guide. However, if you lack proper training or experience, we’d recommend you reach out to a trustworthy professional who can guarantee the best results for help. That said, now let’s take a look at the process.

• Remove the old windows by detaching the old beading and glass window safely. Then make some interval cuts using a hand saw before using a crowbar to pry it out.

• Cut the external double glazed window seal. Once done, take a measurement of the window area’s width once empty. Then transfer the measurement to the window sil to face outside and cut using a handsaw.

• Seal the window sil. Add a bead of clear silicone along both inside lip as well as the centre to seal the sil.

• Screw the double glazed window to the sil. Position the window on the top of the lipped section that was siliconed. Then pre-drill them together and screw in three places. You should make sure the screws do not go totally to the sil’s bottom.

• Install the double glazed window. After successfully screwing the double glazed window to the sil, you can now fit in the double glazing. Make use of packers to make sure it’s even in the slot.

• Screw the uPVC window to the wall. If you’re happy and satisfied with the position of the window, you can then pre-drill through the frame of the window and the brick wall. Once done, simply screw it in place using masonry screws or Spax screw as they do not require crawl plugs in bricks.

• Seal around the window. To do this, simply fill any gaps with expanding foam, wipe out the excess and seal with silicone.

Did you just purchase a double glazed window and confused about how to have it installed? Fitting the window yourself can be quite easy with the help of this step by step guide. However, if you lack proper training or experience, we’d recommend you reach out to a trustworthy professional who can guarantee the best results for help. That said, now let’s take a look at the process.

• Remove the old windows by detaching the old beading and glass window safely. Then make some interval cuts using a hand saw before using a crowbar to pry it out.

• Cut the external double glazed window seal. Once done, take a measurement of the window area’s width once empty. Then transfer the measurement to the window sil to face outside and cut using a handsaw.

• Seal the window sil. Add a bead of clear silicone along both inside lip as well as the centre to seal the sil.

• Screw the double glazed window to the sil. Position the window on the top of the lipped section that was siliconed. Then pre-drill them together and screw in three places. You should make sure the screws do not go totally to the sil’s bottom.

• Install the double glazed window. After successfully screwing the double glazed window to the sil, you can now fit in the double glazing. Make use of packers to make sure it’s even in the slot.

• Screw the uPVC window to the wall. If you’re happy and satisfied with the position of the window, you can then pre-drill through the frame of the window and the brick wall. Once done, simply screw it in place using masonry screws or Spax screw as they do not require crawl plugs in bricks.

• Seal around the window. To do this, simply fill any gaps with expanding foam, wipe out the excess and seal with silicone.

Most window installers will be able to provide you with one double glazed window and fit it for you. If you’re replacing one double glazed window in your home, ask them to try and source the same windows that you already have or find one that’s very similar. Externally, you probably won’t be able to notice the difference, but if your existing windows are very old there may be some exterior discolouration and the locks and handles might look slightly different.

If you want one double glazed window so you can fit it yourself, there are lots of online companies that can supply you with one window. However, window fitting is a skilled trade and you might want to consider whether you have the right tools and experience to fit it yourself. Of course, you’ll save money on installation costs, but if something goes wrong, you might end up shelling out to get it fixed anyway.

The other thing to consider is that any replacement windows need to be certified that they meet Building Regulations. If you fit the double glazed window yourself, you’ll need to apply to your local council building control officer to get a certificate that confirms that you fitted the window within the regulations. You’ll have to pay a fee for this, and it will be even more expensive if Building Control say that the window hasn’t been fitted within the regulations and you have to start again.

The alternative is to ask a reputable window installer that is registered with a self-certification scheme, like FENSA, to install the window. That means that they can self-certify that the window meets building regulations once they’ve finished the installation.

How long your aluminium windows will last depends on their quality. They should last 20 -30 years at least, but have been known to stay in good condition for up to 45 years. This is considerably longer than uPVC and wooden double glazing.