Find a Window Installer you can trust in Cheshire.

No matter how big or small a building is, it can only be as good as it’s foundation - and that’s a fact! It all starts from the footing and when it isn’t deep enough, unlike badly installed gutters or gapped hardwood flooring, can make the whole building collapse to the ground. Just like any code recommendations, the depth of the footings of your porch is a parameter that must be complied with and adjusted to suit your local code requirements.

As a rule of thumb, you should always dig below the frost line when excavating your footings. At this depth level, the moisture present in the soil will be frozen. Ultimately, this will help the ground to act as a barrier to insulate the soil below the footing from freezing during the cold months. As a result, in regions where the weather is almost always very cold the depth of your footings is expected to be at least 48 inches. But in areas featuring a warm climate, you may be allowed to install your footings on grade.

In addition, it’s compulsory that your footings must be installed at a minimum depth of 12 inches below unsettled soil. However, if you’re constructing the structure into a steep hill’s side or by the side of a retaining wall, it’s required that you maintain the least distance to grade both vertically and laterally. In the event whereby you need to achieve a good lateral barrier, you’ll need to have your foundation dug a lot deeper compared to if it’s on a flat surface. For a more accurate and updated information, you can consult your local building inspection department to get familiar with the requirements in your area.

Accidents happen, and sometimes windows get broken. And that will lead to you wanting to replace just the glass in your window, rather than the whole frame. Also, as windows get older they can mist up on the inside, which means that the unit has ‘blown’ - so you’ll also need to replace the glass. But how much is it to replace the glass in a window? Luckily, if the frame of your window is in good condition, there’s no need to replace it, and this will reduce the cost. For an installer to fit a new pane of glass in a single glazed window, the average cost is £100, while a replacement double glazed sealed unit will cost an average of £110. Of course, as this is an average, if your window is very large you may spend more, and if your window is very small the price may be less. That's why it’s important to get a range of quotes so you can compare costs and get the best price. If you’re good at DIY, you may feel confident enough to have a go at replacing the glass in your window yourself. In that case, the cost of sealed unit and any other materials you need will cost an average of £57. It’s a significant saving, and if you think you can do it, then give it a try. However, if you’re in any way unsure, it’s best to leave it to the professionals. A window installer will be able to replace the glass in your window in less than an hour. Even though it costs more for a professional to do it, if you get it wrong and have to start over it will cost you more in the long run.

Whether you need toughened glass in your windows depends on where the windows are in your home or business. Toughened glass is sometimes referred to as tempered or safety glass, and it just means it’s stronger than the standard glass that’s usually offered with double glazed windows. So how do you know if you need it?

Toughened glass is useful in areas of your home where you might come into contact with the windows if you were to trip and fall. If you put your hands out to steady yourself on standard glass the chances are it would break into large sharp pieces with jagged edges. Of course, this means that you could seriously cut yourself if this were to happen. With toughened glass, the structure of the glass is changed so that if it breaks it shatters into lots of tiny pieces, minimising the risk to you if you were to fall on it.

You might want to use toughened glass in patio doors, low windows or frames next to doors. It just means that you will be safer if the unlikely happens and you or a family member falls through the glass. There are certain requirements through Building Regulations with windows at a certain level, but any reputable window installer should be able to go through these with you if you need to replace your windows with toughened glass. The regulations will only apply to new windows – there's no need to switch your windows to toughened glass early, but when you do come to replace them you’ll need to make sure they meet the standard.

Did you just purchase a double glazed window and confused about how to have it installed? Fitting the window yourself can be quite easy with the help of this step by step guide. However, if you lack proper training or experience, we’d recommend you reach out to a trustworthy professional who can guarantee the best results for help. That said, now let’s take a look at the process.

• Remove the old windows by detaching the old beading and glass window safely. Then make some interval cuts using a hand saw before using a crowbar to pry it out.

• Cut the external double glazed window seal. Once done, take a measurement of the window area’s width once empty. Then transfer the measurement to the window sil to face outside and cut using a handsaw.

• Seal the window sil. Add a bead of clear silicone along both inside lip as well as the centre to seal the sil.

• Screw the double glazed window to the sil. Position the window on the top of the lipped section that was siliconed. Then pre-drill them together and screw in three places. You should make sure the screws do not go totally to the sil’s bottom.

• Install the double glazed window. After successfully screwing the double glazed window to the sil, you can now fit in the double glazing. Make use of packers to make sure it’s even in the slot.

• Screw the uPVC window to the wall. If you’re happy and satisfied with the position of the window, you can then pre-drill through the frame of the window and the brick wall. Once done, simply screw it in place using masonry screws or Spax screw as they do not require crawl plugs in bricks.

• Seal around the window. To do this, simply fill any gaps with expanding foam, wipe out the excess and seal with silicone.

uPVC is unplasticised polyvinyl chloride. It is a favourite amongst homeowners and manufacturers for its cheap production cost and excellent benefits. uPVC is used for window frames, conservatories and doors. In fact, uPVC can be three times cheaper than wooden frames and is also the most energy efficient option.As well as this, uPVC is now available in a range of colours other than the typically seen bright white finish. It can also be recycled, is durable and resistant to changing weather conditions.

Are you interested in constructing a porch to your property? Estimating the cost of the project before proceeding will solve a lot of possible headaches in the future.

A porch is great place where you can keep your shoes, jackets, dog leads as well as other items to create free space within the property. Apart from this, a porch also serves numerous other purposes to make it a very good structure to have on your property. Not only is it a good means to put a roof over your head when it’s pouring with rain, but also a highly economical way to add floor space to your home. The question, however, how much would it cost to build a porch?

The price of building a porch is based on a wide variety of factors such as the type of materials required, the size of the porch, location of the structure and lots more. As a result, you should note that this guide provide figures that are only a rough guide that’ll put you on the right direction to make informed decisions.

Depending on the type of porch you choose to build, the average cost range from £1,900 to £2,100 for a uPVC porch and up to £10,000 for a lean to porch. There are other types of porch including the traditional porches ( Edwardian and Victorian porches) costing within a range of £2,500 to £8,400.

The materials required also has a great influence in determining the price of a porch. An aluminium porch will cost between £7,5000 to £8,200, while a brick porch will cost slightly less between the range of £2,000 to £8,000. They can both be constructed either as a front porch or as a rear porch, but due to fewer restrictions on aluminium porch, it can be made a lot larger.

If a window is double glazed, it has two panes of glass that have a space between them containing argon gas. The gas works as an insulator, keeping heat inside the house as well as reducing noise. It also strengthens the window.

Using a Fensa registered installer isn’t compulsory but it helps to protect you from cowboys and rogue traders. It will also make life a whole lot easier in regards to Building Regulations. Replacement windows must meet a certain energy efficiency rating and once fitted you need a certificate to show your installation complies. By using a Fensa registered company they’ll issue this certificate, otherwise you’ll need the council to look at the new windows.