Find a Solar Panel Installer you can trust in Newton Stewart.

How long your solar panels will last depends on their age and quality. Most modern solar panels have 20-30 year warranties, but this doesn’t mean that they’ll stop working at this point. Many will stay at a good efficiency level for up to 40 years, while others will start to decline earlier.

How Much To Install Solar Panels And Battery?

Are you thinking about installing solar panels and battery in your home and wondering how much the installation is going to cost? Well, you’re not alone. This is one of the most commonly asked questions in the solar world, but unfortunately a precise answer can not be provided. This is mainly due to the fact that solar panel systems come in varying sizes which is the main influencing factor that determines how much electricity that can be generated. In other words, the larger the system, the more the electricity that’ll be produced to your home’s benefit.

Generally, for a solar system size of 1kW, the average cost of the solar panel ranges between £1800 to £1850, 2kW is between £3600 to £3700, solar panel size of 3kW ranges between £5500 to £5600 and finally, 4kW is between £6000 to £6050. For example, with the aforementioned prices in mind, the cost of solar panels for a standard 3 bedroom house will range between £5520 to £6040 as the high electricity demands will need the installation of 3 to 4kW solar system size.

Meanwhile the installation cost of solar batteries is also dependent on a number of influencing factors like the size as well as the make of the battery. Generally, you can expect to spend within the range of £500 to £2000 to install your batteries depending on aforementioned factors. In the event whereby you’ll be retrofitting, you might also need to include an additional cost of £1000 for an inverter. However, it’s important to note that there are only quite a few hybrid systems which are able to combine a battery storage with an inverter.

If you’re considering getting a solar thermal system, one of the first things that comes to mind is the possibility of the system functioning properly during the cold months. The short and simple answer to this question is yes, a solar thermal system works in the winter. However, the downside here is that it’ll be a lot less efficient when compared to how it operates during the warmer months or summer. As a result of this fact, you’ll likely need to rely more on your boiler, immersion heater or any other backup heating system during this period as your solar thermal system will fail to contribute as much as it does during the warmer months. So what exactly is the reason why solar thermal is less effective and less efficient in the winter period? Let’s have a look!

As you know, solar thermal system banks on the sun’s energy to heat the water for your home’s use. During the cold months or winter, the sunlight becomes a lot less available when compared to the warmer months, as a result, there’s less sunlight that’s available to be used for its solar energy. And even more so at the periods when the days are shorter or skies are clearly overcast.

Also having a great impact on a solar thermal system’s output is heavy snow. Flat plate collectors normally have the capacity to cope better during snowy conditions as the light that’s able to travel through the snow will heat up the absorber plate - thereby making the snow slide off more quickly. However, the case is contrary with evacuated tube collectors which possesses a form of vacuum insulation that’s crafted to minimize the loss of heat, meaning they can’t generate heat to melt and cause the snow to slide off in a similar way.

Solar PV panels work by converting sunlight into electricity. They’re made up of photovoltaic cells, which take in the sun’s rays and turn it into direct current (DC) electricity. The current is then channelled into an inverter, which converts it to alternating current (AC).

Once converted to AC, the electricity is ready to use. It’s fed through a meter and into your property’s consumer unit, and is automatically used to power appliances and heating systems. Your system will automatically switch between your solar electricity supply and the national grid, and export any solar electricity you don’t use to the national grid.

1. After the installer’s measured up, given you an estimated output and recommended some systems for you, they’ll arrange date to come to your home to install the solar thermal panels. They’ll also let you know if any scaffolding will be required.
2. Next, they will start to fit the panels, or collectors, to your roof. Stainless steel brackets will be provided with the system and they will remove your roof tiles or slates to attach the brackets to the rafters. They’ll then replace the tiles and add waterproof flashing to ensure you don’t get any roof leaks, and add the frame.
3. If you’ve chosen evacuated tube solar thermal panels, the installer will bolt the heat transfer unit to the top of the frame but not install the tubes until nearer the end. This is because the tubes start to transfer heat to the exchanger immediately, and when everything is unconnected this could damage the unit.
4. If you don’t need a new boiler with your installation, a new dual coil water cylinder, pump and system control system will be fitted. It’s best in a loft or upper floor of your home.
5. A new thermal store or hot water tank that will store the heat provided by the solar system is much larger than a standard tank but it may fit in the spot of your old one. The installer will ensure that it’s connected to the mains cold water, your other heating source (such as a gas boiler or biomass boiler), immersion heater, temperature sensors and the solar collectors themselves.
6. Next they will install the pumping station, usually near the water tank. The expansion tank will be installed on the solar thermal loop, which is usually nearby. Its job is to prevent pressure changes that could damage the system.
7. You’ll get a heat generation meter which must be MCS-certified if you want to take advantage of the RHI, and any control equipment that comes with the system will be installed.
8. The installers will then bring the system to pressure by pumping the heat transfer liquid into the system up to a pressure of around 2 bar.
9. Finally, your MCS-registered installer will register your solar thermal system so you can apply for RHI payments of up to £525 per year.
So that’s the process of installing solar thermal panels. Remember – it's always best to use a professional to install any kind of renewable technology.

If you’re looking to install some new solar panels in your home or property, then you’d probably want to know how it works. This is one of the most frequent questions asked by homeowners when it comes to solar panels and in this article we aim to give you a good insight on the operations of solar panels. Let’s have a look!

Generally, solar panels work by absorbing the energy of the sun and then converting it into electricity. It functions by allowing photons from the rays of the sun release the electrons free from atoms within the photovoltaic or solar cells in order to produce a flow of electricity. There are several solar cells that are connected together ( usually 60 or 72 ) in each panel. Individual cells comprises both a negative layer and a positive one which combines perfectly to create an electrical field in which the energy is generated.

The boron that’s within the bottom layer generates the positive charge, while the phosphorous found in the silicon layer produces the negative charge. In order to convert the sun’s rays into the energy that’s going to be transported from the panels to the inverter, the two field will interact with one another.

In other words, solar panels work by turning photons from the sunlight into direct current which is transmitted to the inverter. Once it gets to the inverter, it’s then translated to alternating current and send this current to to your electric box which powers the entire home. If you do not wish to reduce the high bills that’s associated with renting power from the grid, the solar energy system is an efficient and affordable way to achieve this aim.

So, you’ve finally decided to go for solar? If yes, then you’d also probably find yourself trying to figure out exactly what solar battery size is needed to power your home or property. This is one of the most common questions when it comes to the solar system world and understandably so. In this article, we aim to give you an idea of the solar size you’d need to power your home or property before making a purchase decision. Let’s take a look!

The first thing to do if you find yourself asking this question is to identify the reason why you want to purchase the solar battery in the first place. For some individuals, they simply want to save some excess energy being fed back into the grid, while others just want protection from possible blackouts. There are also some environment-conscious home or property owners who makes this decision in order to create a carbon-neutral home. Another crucial factor to consider is your budget. A full solar storage system can be quite costly, although this is cheaper than a decade ago. Generally, the size of solar battery you’ll require depends on the following:

• How much energy you’re able to generate: The size of your solar array as well as its efficiency will influence the amount of power it’ll be able to supply to your home.
• Your daily energy usage needs: Daily energy usage can vary greatly between households depending on a number of factors. These factors include the number of occupants, geographical location, type of building, general household energy usage and more. Some may find that their solar system cover for most of their energy usage, while others find themselves still relying heavily on the grid.