Find a Solar Panel Installer you can trust in Tipton.

1. After the installer’s measured up, given you an estimated output and recommended some systems for you, they’ll arrange date to come to your home to install the solar thermal panels. They’ll also let you know if any scaffolding will be required.
2. Next, they will start to fit the panels, or collectors, to your roof. Stainless steel brackets will be provided with the system and they will remove your roof tiles or slates to attach the brackets to the rafters. They’ll then replace the tiles and add waterproof flashing to ensure you don’t get any roof leaks, and add the frame.
3. If you’ve chosen evacuated tube solar thermal panels, the installer will bolt the heat transfer unit to the top of the frame but not install the tubes until nearer the end. This is because the tubes start to transfer heat to the exchanger immediately, and when everything is unconnected this could damage the unit.
4. If you don’t need a new boiler with your installation, a new dual coil water cylinder, pump and system control system will be fitted. It’s best in a loft or upper floor of your home.
5. A new thermal store or hot water tank that will store the heat provided by the solar system is much larger than a standard tank but it may fit in the spot of your old one. The installer will ensure that it’s connected to the mains cold water, your other heating source (such as a gas boiler or biomass boiler), immersion heater, temperature sensors and the solar collectors themselves.
6. Next they will install the pumping station, usually near the water tank. The expansion tank will be installed on the solar thermal loop, which is usually nearby. Its job is to prevent pressure changes that could damage the system.
7. You’ll get a heat generation meter which must be MCS-certified if you want to take advantage of the RHI, and any control equipment that comes with the system will be installed.
8. The installers will then bring the system to pressure by pumping the heat transfer liquid into the system up to a pressure of around 2 bar.
9. Finally, your MCS-registered installer will register your solar thermal system so you can apply for RHI payments of up to £525 per year.
So that’s the process of installing solar thermal panels. Remember – it's always best to use a professional to install any kind of renewable technology.

• The power of your solar panel system – there's no point buying a higher capacity battery if your system will never generate enough electricity to charge it
• How often you think you will need to charge your battery
• Your budget
• Whether you care about having the latest technology and a recognisable brand name

There are two different types: flat plate, where lots of thin tubes carry water through a flat absorber panel, and evacuated tube, where vacuum glass tubes capture the sun’s energy directly. There is little difference in performance between the two but evacuated tube panels do more obviously extrude from the roof.

If you’re thinking of adding a solar battery to your home, you might be wondering whether or not it’s going to work in a power cut. If yes, then you’re not alone as this is one of the most common questions asked when it comes to solar batteries. In this post, we aim to provide you with a detailed answer to solve this concern once and for all.

The answer to this question is, it depends. The main reason why your solar batteries will usually not work or provide your home with the much-needed back up power is as a result of the several threats it poses. You should be aware that both your solar panels and battery are connected to the main grid. When a power cut occurs, your engineers will have to operate on the grid. If the solar panels or batteries are in operation at the period there’s a high chance the engineers would be electrocuted by the electricity that’s being produced. As a result of this, solar inverters are usually designed to automatically switch off once a power cut occurs. However, it should also be noted that if your solar battery possesses backup functionality, you’ll be able to make use of your solar energy in the event of a power cut. In other words, what determines if your home battery would work in a power cut is the availability or otherwise of a backup functionality.

Furthermore, you might also wish to know if your solar panels will continue to charge the battery in a power cut. Well, this depends on the type of backup system you possess. There are some more affordable batteries that are designed to automatically release their stored energy upon the detection of a power cut. And this is mostly because the battery inverter is usually smaller than the solar inverter which allows the energy from the solar inverter to the transmitted to the battery - risking an overload. However, if otherwise, then energy can continue to be transmitted to the battery until its fully charged.

If you want to test your solar panel system to see if it’s working properly or just to see what output it’s giving, you can do this using a multimeter to measure current, or amps, and voltage.

Before you start, you’ll need to find the voltage (v) and current (A) ratings of your panel. You should be able to find them on the back of the panel. You should also make sure that it’s a nice clear, sunny day to get the best readings out of your panel. You should also check that it’s safe to be up on your roof!

To measure open circuit voltage, you’ll need to make sure that your solar panel is completely disconnected from your system’s regulator and battery (if you have one). Angle the panel towards the sun, and ensure that your multimeter is set to measure volts. Measure the voltage between the positive and negative terminals by connecting the negative contact on the voltmeter to the negative on the panel and the positive contact on the voltmeter to the positive on the panel.

Then, you can move on to the short circuit current. Follow the same steps as the open circuit voltage, but ensure that your multimeter is set at 10A to start with.

Only try to test your solar panel if it’s safe to do so. If your roof isn’t accessible without scaffolding or specialist equipment, consider speaking to an MCS-registered solar company about your concerns. They may recommend that they come to service your solar panel system.

To have your solar panels working at full strength at all times is crucial as this can go a long way to help you reduce your energy bill. In order to achieve this, you simply can’t afford to ignore having them regularly cleaned and free from all sorts of dirt, dust, debris, pollen, bird droppings and the likes. Now it’s quite reasonable to think rain or wind should be able to get the job done, but unfortunately this is not so. What solar panels need is a proper clean which you can decide to do by yourself or call in a qualified professional – the latter which is strongly recommended.

Cleaning of solar panels has to do with working at heights which can be very dangerous especially if you don’t have enough confidence to pull it off. And even if you have zero phobia for heights, solar panel cleaning requires experience as well as some specialized skills and tools possessed by the professionals. However, the question here is, how often should solar panels be cleaned to keep them operating at optimal efficiency?

Well, according to the manufacturers, solar panels should be cleaned twice a year. However, if this is something that you feel is not achievable by you, then you should at least give then an annual clean. The best or most advisable time to do this during the year is at the end of the summer months. This will ensure that you have a fully functioning solar array which is ready and prepared to withstand whatever the cold period throws at you. At the end of the day, you’d have them looking spotless clean while also working at full strength and reducing your energy bills.

Installing solar panels for your business operations can provide you with a number of impressive benefits. It is not only capable of helping you minimize your business’ environmental footprint but it can also go a long way to help you save money. Irrespective of your company’s size, whether big or small, it can still benefit immensely by making use of solar panels. If you’re currently planning to install solar panels in your business environment, then you’d probably want to know just how much it’ll cost to complete the project. In this post, we aim to give you a good insight into commercial solar panel pricing so as to help you make the best informed decisions possible . Let’s take a look!

In truth, there’s no single and accurate answer to this question as there are a number of factors that can influence the cost of commercial solar panels. These factors include the size of the roof, the amount of energy that’s generated as well as the number incorporated. To give you a general idea, the price of solar panels for commercial property is usually within the range of £16000 to £70000 for small to mid-sized companies. For a more accurate estimate, you’ll need to get in touch with a professional with your unique needs.

There is also a need to evaluate the cost of solar panels so as to determine whether or not they’re a feasible option for your business. In order to determine the amount of energy your company uses per month, simply take a closer look at your utility bill.  This should indicate just how much energy you use per month as well as how much the utility company charges per kW. In general, most small to medium sized companies will incorporate 30,000 to 50,000 kWh annually and you can expect the cost to differ based on your location and the size of your system. The rule of thumb with larger systems is to calculate using £1000 per kW, plus VAT as the yardstick.

Solar energy is renewable, as the sunlight it uses won’t run out. This means that it’s a great way to generate electricity without damaging the planet. So, installing solar panels to generate solar energy can be a great move for businesses looking to reduce their carbon emissions.