Find a Solar Panel Installer you can trust in Dunkeld.

Yes – solar thermal can be used for central heating. Solar thermal panels work by collecting heat from the sun, either through evacuated tubes or flat plate collectors, and transferring that to a heat transfer liquid that heats your hot water. This can then be used to preheat your central heating.

You’ll need a hot water cylinder to store the water that your solar thermal panels heat up. It’s likely that you’ll need an immersion heater or boiler to heat the water further so you can use it for your central heating, and as a back-up during the longest winter months since the solar panels won’t be able to generate as much heat.

In our opinion, it’s best to use your solar thermal panels for hot water rather than your central heating. That’s because you use hot water all year round, whereas you probably won’t have your central heating on in the spring and summer, when the panels can generate the most heat. For central heating, air- or ground-source heat pumps are a great renewable option, and you can even power them with electricity from solar PV panels if you want to be as eco-friendly as possible.

In a similar way to other major home improvement projects, some specific requirements must be met to allow for the installation of solar panels. The main reason why these standards and regulations were established is to minimize the risk of the solar system becoming an issue or potential hazard in the unforeseeable future. So if you’re thinking about buying and fitting new solar panels, you’ll probably want to know whether or not you’ll require to submit a planning permission application for approval before you can proceed.

Generally, solar panels are covered under what’s called “Permitted Development” which gives you the freedom to install your solar panels without having to apply for a planning permission. However, there are some exceptions to this rule. These exceptions include if your house is a listed building or if your house is located within a conservation area. In these exceptional cases, it’s possible that you’ll need to apply for a planning permission, but this will largely depend on the discretion of your Local Planning Authority. What’s more? Solar panels are usually subjected to normal building regulations which includes examining the roof to make sure that it can support the additional weight. You can call in a MCS certified installer to carry out this check for you.

In order to install your solar PV on your roof, you must follow these guidelines:

✓ Your solar panels shouldn’t go beyond the highest point of the roof (excluding chimneys).

✓ The solar panels shouldn’t project beyond 200mm off the roof’s edge.

✓ The solar panels should be removed once they’re no longer used to produce electricity

✓ The solar panels should be installed such that the area and building’s appearance change is minimized.

When you’re about to transform from the standard electricity to solar energy, what determines your solar system’s size is the amount of solar that’s required. The amount of solar that you’ll need, on the other hand, requires considering the end goal, be it to increase money savings, reduce environmental contamination, maximize Returns On Investment ( ROI), or just to copy what the neighbour’s done.

In order the determine the number of solar panels that is needed, the first step would be to calculate the number of kWhs that’s currently being used. A kWh is what’s used to determine the amount of energy that has been incorporated over time which the utility uses to bill you. What’s strongly recommended to create a suitable range is a 6 to 12 months average of your household electricity bill. Other factors that can play a key role in the determination of the number of solar panel needed include the following:

✓ Sunlight exposure hours. In order to know just how much energy your solar panels will generate, there’s a need to know the number of direct sunlight hours you should expect on a daily basis. For example if you stay in a region that’s usually very sunny, then it’ll be reasonable to expect more energy production per panel than regions that are usually cloudy.

✓ Angle and size of the roof. Roofs with a lot of workable space may require to let go of some efficiency opting for larger and cost effective panels to achieve the targeted energy. However not all homeowners have sufficient roof space or shade coverage for the solar panel they actually want. Also, the degree at which the roof slants will also determine if the sunlight is hitting the panels well enough and the amount of energy that can be generated thereof.

If you want to test your solar panel system to see if it’s working properly or just to see what output it’s giving, you can do this using a multimeter to measure current, or amps, and voltage.

Before you start, you’ll need to find the voltage (v) and current (A) ratings of your panel. You should be able to find them on the back of the panel. You should also make sure that it’s a nice clear, sunny day to get the best readings out of your panel. You should also check that it’s safe to be up on your roof!

To measure open circuit voltage, you’ll need to make sure that your solar panel is completely disconnected from your system’s regulator and battery (if you have one). Angle the panel towards the sun, and ensure that your multimeter is set to measure volts. Measure the voltage between the positive and negative terminals by connecting the negative contact on the voltmeter to the negative on the panel and the positive contact on the voltmeter to the positive on the panel.

Then, you can move on to the short circuit current. Follow the same steps as the open circuit voltage, but ensure that your multimeter is set at 10A to start with.

Only try to test your solar panel if it’s safe to do so. If your roof isn’t accessible without scaffolding or specialist equipment, consider speaking to an MCS-registered solar company about your concerns. They may recommend that they come to service your solar panel system.

How Many Solar Panels And Batteries To Power A House?

Do you wish to know the number of solar panels and batteries sufficient for a house? Well, this is a frequently asked question in the solar world which would be very difficult to provide an accurate answer. This is basically down to the fact that all homes are unique with different sizes as well as amount of daily energy requirements. As a result, the number of solar panels and batteries needed would be unique to the house in question. However, we’ll consider the varying influencing factors that will go a long way to help calculate the number of panels and batteries needed to power a house.

First and foremost, let’s take a look at the solar panels. You’d have to start here by putting into consideration all household appliances that makes use of power in the house to get a good idea of how many that’ll be needed.

• How Many Watts Is Being Used In The House On A Daily Basis?

To determine this, simply go through your utility bill for kilowatt-hours (kWh). This varies amongst homes and being able to identify your daily average energy usage will assist you in getting your solar needs.

• What Is The Number Of The Peak Sunlight Hours At The House’s Location?

Having in mind that the solar panels only work when under direct sunlight, the first step to determine the peak sunlight hours. Once determined, you can then multiply the figure in hours by the house’s hourly energy usage and divide by the solar panel’s wattage.

Overall for a 1500 square foot house, the number of solar panels that’ll be required should fall around 15 to 18.

Meanwhile for batteries, there are also some factors to be considered to determine the number of batteries that is required to power a house. These factors include the house’s power or electricity usage, the period of time in which the battery will be used as well as the battery’ specifications.

If you want to connect solar panels to a battery, it’s likely that it’s because you want to make sure that you don’t waste any electricity when your solar panels are generating energy but you’re not around to use it. Batteries are particularly useful for homeowners that have solar panels but are out during daylight hours; with a solar battery system, your solar panels will feed the electricity they generate into the battery for you to use when you get home.

If you want to connect your solar panels to a battery, the best thing to do is to get in touch with an MCS-registered company who can talk you through your options. There are different size batteries and the size that’s suitable for you will depend on how much electricity you plan to store and how large your solar panel system is. Some of the top brands of battery storage system include Tesla, SunPower and SolarEdge. If you want to be able to take advantage of selling electricity back to the grid through the Smart Export Guarantee (SEG), it’s worth getting an MCS-registered company to install your battery for you, as you may not be eligible for payments if you connect your solar panels to a battery yourself.

You should also consider whether your solar panel system is a ‘storage ready’ solar system. Today, most systems will be, since battery storage is becoming much more common. This means that your solar panel system will have an inverter that can easily integrate a battery. If this is the case, you should be able to purchase the battery you want and follow the manufacturer’s instructions to install it.

However, it’s worth bearing in mind that electricity is extremely dangerous when handled incorrectly. If something goes wrong, you could electrocute yourself or cause a fire. If your solar panels and battery cause a fire, it’s unlikely that your home insurance company would pay out if you connect the battery yourself. That's why it’s best to ask a reputable installer with all the correct qualifications to connect your solar panels to a battery for you.