Find a Solar Panel Installer you can trust in Mindrum.

With the numerous benefits that comes with the installation of solar panels, it should not be an option for just a few just because of the size and/or pitch of their roof. A number of individuals with flat roofs decide against solar panels due to the fact that they believe that the panels can’t be installed due to the lack of direct sunlight. However, in truth, this thought is absolutely incorrect. This is because it is actually very possible to fit solar panels on flat roofs and you can also benefit from a good amount of electricity that’ll be generated over time. In this post, we’re going to look at the possibilities involved in the installation of commercial solar panels on a flat roof. Let’s get started!

In reality, flat roof solar systems are mostly found on commercial buildings as their roof is typically made to be flat. Although, it’s important to note that it’s absolutely possible for them to be fitted on domestic properties too. The type of solar array that’s installed makes use of the same type of solar panel as a conventional system, however, there are some considerations that’ll have to be made moving forward. The array must be able to self clean during the rainy season while also avoiding damage whenever there’s a strong wind. The installation company you choose should take the pitch of the system into account, so as to make sure that its able to capture as much energy from the sun as possible. And that’s exactly why you should consider the use of thin film solar cells which are very flexible and moves with the sun as the day goes by, securing as much sunlight as possible as its always in direct light.

No – solar thermal doesn’t generate electricity. Unlike solar PV, solar thermal panels harness the sun’s energy and convert it into heat which is then transferred into your home.

You can have evacuated tube solar thermal panels or flat plate collectors; evacuated tubes are thought to be more efficient that flat plate collectors. They both work by using the sun’s rays to heat a transfer fluid, usually made from water and a type of antifreeze, which is pumped to a heat exchanger inside a water tank in your home. The heat from the exchanger heats the water inside your tank, then when the liquid releases its heat it’s transferred back to the collectors to start the whole process again.

You’ll need to use your solar thermal panel system with a boiler, collector or immersion heater. This is so that the water can be stored and used for your hot water and heating, and also because in the UK, people generally need to rely on another source of heating in the winter. There are fewer sunlight hours in the winter months, so it’s not often possible for solar thermal panels to generate enough heat from the sun to get your water up to temperature.

Whatever the time of year it is, you might want to heat the water up further than your solar panels can manage. That’s why you’ll still need a form of traditional hot water heating, but you should see savings on your energy bills. If you’re currently using natural gas, you can expect savings of around £60 per year on your fuel bills, while if you’re using LPG it could be as high as £100 pr year

How Much To Install Solar Panels And Battery?

Are you thinking about installing solar panels and battery in your home and wondering how much the installation is going to cost? Well, you’re not alone. This is one of the most commonly asked questions in the solar world, but unfortunately a precise answer can not be provided. This is mainly due to the fact that solar panel systems come in varying sizes which is the main influencing factor that determines how much electricity that can be generated. In other words, the larger the system, the more the electricity that’ll be produced to your home’s benefit.

Generally, for a solar system size of 1kW, the average cost of the solar panel ranges between £1800 to £1850, 2kW is between £3600 to £3700, solar panel size of 3kW ranges between £5500 to £5600 and finally, 4kW is between £6000 to £6050. For example, with the aforementioned prices in mind, the cost of solar panels for a standard 3 bedroom house will range between £5520 to £6040 as the high electricity demands will need the installation of 3 to 4kW solar system size.

Meanwhile the installation cost of solar batteries is also dependent on a number of influencing factors like the size as well as the make of the battery. Generally, you can expect to spend within the range of £500 to £2000 to install your batteries depending on aforementioned factors. In the event whereby you’ll be retrofitting, you might also need to include an additional cost of £1000 for an inverter. However, it’s important to note that there are only quite a few hybrid systems which are able to combine a battery storage with an inverter.

Solar panels are made up of photovoltaic (PV) cells. These cells are made from silicon semiconductors, which absorb sunlight and convert it into electricity.

There are three main types of PV cell: monocrystalline solar cells, polycrystalline solar cells, and thin film solar cells. Monocrystalline cells are usually the most efficient and expensive, and thin film solar cells are the cheapest and least efficient. These are all made from silicone, but are manufactured in different ways.

Solar thermal panels work by capturing heat directly from the sun and using it to heat water. This hot water is then passed through a coil to heat the water for your central heating system. Solar thermal systems are compatible with many existing conventional boilers with hot water tanks, and can be set up to feed in to your existing heating system.

If you want to test your solar panel system to see if it’s working properly or just to see what output it’s giving, you can do this using a multimeter to measure current, or amps, and voltage.

Before you start, you’ll need to find the voltage (v) and current (A) ratings of your panel. You should be able to find them on the back of the panel. You should also make sure that it’s a nice clear, sunny day to get the best readings out of your panel. You should also check that it’s safe to be up on your roof!

To measure open circuit voltage, you’ll need to make sure that your solar panel is completely disconnected from your system’s regulator and battery (if you have one). Angle the panel towards the sun, and ensure that your multimeter is set to measure volts. Measure the voltage between the positive and negative terminals by connecting the negative contact on the voltmeter to the negative on the panel and the positive contact on the voltmeter to the positive on the panel.

Then, you can move on to the short circuit current. Follow the same steps as the open circuit voltage, but ensure that your multimeter is set at 10A to start with.

Only try to test your solar panel if it’s safe to do so. If your roof isn’t accessible without scaffolding or specialist equipment, consider speaking to an MCS-registered solar company about your concerns. They may recommend that they come to service your solar panel system.

Like every other systems in your home, solar hot water systems will require periodic inspections as well as a regular maintenance in order to keep it running as efficiently as it should. Not only that, the various components will also require either repair or replacement from time to time. It’ll also be proactive to take the necessary precautions so as to prevent worrying issues like corrosion, scaling or freezing.

Is it a task you can handle on your own? Well, there are some inspections and maintenance activities you should be able to handle on your own, however, you’ll also require a qualified technician to carry out the more technical or complicated tasks. You should also take note that it may actually be more cost effective to have some systems replaced, shut off or removed completely than having it repaired. Here are some of the essential inspections that should be carried out on solar system components. They include:

✓ Collector soiling. Periodic cleaning of your collectors is important especially in dry and dusty climates.

✓ Plumbing, ductwork and wire connections. Check the pipe connections for fluid leaks. Examine duct connections and seals. Also make sure that all wire connections are tight.

✓ Roof penetrations. Flashing and sealant around the roof penetration should be checked to see that it’s in a good shape.

✓ Collector shading. Check for shading of the collectors on annual basis as this may greatly affect their performance.

✓ Support structures. Examine all bolts and nuts which connects the support structures to the collectors for tightness.

✓ Heat transfer fluids. Anti freeze solutions in liquid solar heating collectors will have to be replaced periodically. And this right here is a task that’s best handled by a licensed technician.

After making the very important business decision to go solar, you may also want to know just how long it’ll take to complete the installation process and start generating electricity. After all, generating electricity is the main reason you made the switch to solar system. In this post, we’re going to provide you with in depth details on how long it takes to install solar panels as well as the factors that may affect that time.

The entire process of solar panels installation and getting them approved isn’t an overnight process. You’ll have to wait for periods for each step of the process whereby one must be completed before moving to the next. The time required to complete each step can, however, vary largely depending on your location, the type of solar panels you opt for, the solar company you hire as well as the number of people that’ll be making the installation. Here are the steps to a solar system installation and the estimated time each are expected to take:

• Site assessment. Once you chosen your solar company, the first step would be to have a solar professional from the company to visit the site to examine the roof and other features so as to make sure that they’re able to support a solar system. From the initial contact to scheduling the site visit, this step can take up to 1 to 2 weeks
• Local permitting. This involves getting the right permits from your local authorities. This can take up to 3 to 6 or more weeks.
• Solar system design. This may take up to a week or two depending on whether or not you need design approval and also where the parts are coming from
• Installation. This step can take a week or two depending on the size af your solar panel and roof.
• Inspection. This step can take up to a week depending on where you reside and how quickly the inspector can visit.
• Utility connection. Depending on your utility company, this step can take up to 2 weeks.