Find a Solar Panel Installer you can trust in Chathill.

If you want to test your solar panel system to see if it’s working properly or just to see what output it’s giving, you can do this using a multimeter to measure current, or amps, and voltage.

Before you start, you’ll need to find the voltage (v) and current (A) ratings of your panel. You should be able to find them on the back of the panel. You should also make sure that it’s a nice clear, sunny day to get the best readings out of your panel. You should also check that it’s safe to be up on your roof!

To measure open circuit voltage, you’ll need to make sure that your solar panel is completely disconnected from your system’s regulator and battery (if you have one). Angle the panel towards the sun, and ensure that your multimeter is set to measure volts. Measure the voltage between the positive and negative terminals by connecting the negative contact on the voltmeter to the negative on the panel and the positive contact on the voltmeter to the positive on the panel.

Then, you can move on to the short circuit current. Follow the same steps as the open circuit voltage, but ensure that your multimeter is set at 10A to start with.

Only try to test your solar panel if it’s safe to do so. If your roof isn’t accessible without scaffolding or specialist equipment, consider speaking to an MCS-registered solar company about your concerns. They may recommend that they come to service your solar panel system.

There are two different types: flat plate, where lots of thin tubes carry water through a flat absorber panel, and evacuated tube, where vacuum glass tubes capture the sun’s energy directly. There is little difference in performance between the two but evacuated tube panels do more obviously extrude from the roof.

The more you’re at home during the day, the more you can save on your electricity bill, since solar panels generate electricity during the day. The Feed-in Tariff scheme (FITs) ended in March 2019, but the new Smart Export Guarantee (SEG) pays you, via your energy supplier, for the electricity you export back to the grid. With the savings involved in generating your own electricity and SEG payments, you can expect to save up to £390 per year on your electricity bill.

1. After the installer’s measured up, given you an estimated output and recommended some systems for you, they’ll arrange date to come to your home to install the solar thermal panels. They’ll also let you know if any scaffolding will be required.
2. Next, they will start to fit the panels, or collectors, to your roof. Stainless steel brackets will be provided with the system and they will remove your roof tiles or slates to attach the brackets to the rafters. They’ll then replace the tiles and add waterproof flashing to ensure you don’t get any roof leaks, and add the frame.
3. If you’ve chosen evacuated tube solar thermal panels, the installer will bolt the heat transfer unit to the top of the frame but not install the tubes until nearer the end. This is because the tubes start to transfer heat to the exchanger immediately, and when everything is unconnected this could damage the unit.
4. If you don’t need a new boiler with your installation, a new dual coil water cylinder, pump and system control system will be fitted. It’s best in a loft or upper floor of your home.
5. A new thermal store or hot water tank that will store the heat provided by the solar system is much larger than a standard tank but it may fit in the spot of your old one. The installer will ensure that it’s connected to the mains cold water, your other heating source (such as a gas boiler or biomass boiler), immersion heater, temperature sensors and the solar collectors themselves.
6. Next they will install the pumping station, usually near the water tank. The expansion tank will be installed on the solar thermal loop, which is usually nearby. Its job is to prevent pressure changes that could damage the system.
7. You’ll get a heat generation meter which must be MCS-certified if you want to take advantage of the RHI, and any control equipment that comes with the system will be installed.
8. The installers will then bring the system to pressure by pumping the heat transfer liquid into the system up to a pressure of around 2 bar.
9. Finally, your MCS-registered installer will register your solar thermal system so you can apply for RHI payments of up to £525 per year.
So that’s the process of installing solar thermal panels. Remember – it's always best to use a professional to install any kind of renewable technology.

If your solar panels are mounted on your roof and you require a ladder to reach them we would always recommend you get a professional to do the work for your own safety.

How Do Solar Panels And Batteries Work Together?

With solar panel system rapidly becoming an ubiquitous phenomenon within the modern society, several homeowners in the UK are just coming to terms with the numerous benefits offered by the system. The solar power’s popularity has even led to the rise of another renewable technology - solar batteries able to store excess solar power that can be used later. Now several companies such as Tesla are now building solar batteries that can be fitted alongside solar panels for your building. So how exactly do solar panels and batteries work together? Let’s have a look!

Solar panels make use of the sun light to generate electricity and as a result, they can’t function when sunlight is absent - giving a big issue of how to power your house when it’s dark. In the event whereby this occurs, you’re afforded two options which is either to contact energy providers to buy electricity or purchase a battery storage system.

So what’s the function of the battery storage system? Basically when your solar panel provides electricity which is not needed right away, a solar battery will work to convert the DC electricity into AC energy which is going to be stored for later use (when you actually need it). in other words, your solar panels charge the batteries when you do not require the energy they’re generating right away.

As a result, when it’s dark and the solar panels are no longer functioning, your system will tap into the energy that’s already been stored by your battery for later use. This way, you can be totally independent of the National Grid, which implies more savings on your electricity bills.