Find a Solar Panel Installer you can trust in Romney Marsh.

The lifetime of a solar panel depends on its quality and age. Generally, the older a solar panel gets, the less efficient it becomes. The majority of modern solar panels come with 20-30 year warranties, which means that they’ll stay at a good efficiency level for at least this long. Some panels can stay efficient for as long as 40 years, while others won’t last this long.

1. After the installer’s measured up, given you an estimated output and recommended some systems for you, they’ll arrange date to come to your home to install the solar thermal panels. They’ll also let you know if any scaffolding will be required.
2. Next, they will start to fit the panels, or collectors, to your roof. Stainless steel brackets will be provided with the system and they will remove your roof tiles or slates to attach the brackets to the rafters. They’ll then replace the tiles and add waterproof flashing to ensure you don’t get any roof leaks, and add the frame.
3. If you’ve chosen evacuated tube solar thermal panels, the installer will bolt the heat transfer unit to the top of the frame but not install the tubes until nearer the end. This is because the tubes start to transfer heat to the exchanger immediately, and when everything is unconnected this could damage the unit.
4. If you don’t need a new boiler with your installation, a new dual coil water cylinder, pump and system control system will be fitted. It’s best in a loft or upper floor of your home.
5. A new thermal store or hot water tank that will store the heat provided by the solar system is much larger than a standard tank but it may fit in the spot of your old one. The installer will ensure that it’s connected to the mains cold water, your other heating source (such as a gas boiler or biomass boiler), immersion heater, temperature sensors and the solar collectors themselves.
6. Next they will install the pumping station, usually near the water tank. The expansion tank will be installed on the solar thermal loop, which is usually nearby. Its job is to prevent pressure changes that could damage the system.
7. You’ll get a heat generation meter which must be MCS-certified if you want to take advantage of the RHI, and any control equipment that comes with the system will be installed.
8. The installers will then bring the system to pressure by pumping the heat transfer liquid into the system up to a pressure of around 2 bar.
9. Finally, your MCS-registered installer will register your solar thermal system so you can apply for RHI payments of up to £525 per year.
So that’s the process of installing solar thermal panels. Remember – it's always best to use a professional to install any kind of renewable technology.

Like every other systems in your home, solar hot water systems will require periodic inspections as well as a regular maintenance in order to keep it running as efficiently as it should. Not only that, the various components will also require either repair or replacement from time to time. It’ll also be proactive to take the necessary precautions so as to prevent worrying issues like corrosion, scaling or freezing.

Is it a task you can handle on your own? Well, there are some inspections and maintenance activities you should be able to handle on your own, however, you’ll also require a qualified technician to carry out the more technical or complicated tasks. You should also take note that it may actually be more cost effective to have some systems replaced, shut off or removed completely than having it repaired. Here are some of the essential inspections that should be carried out on solar system components. They include:

✓ Collector soiling. Periodic cleaning of your collectors is important especially in dry and dusty climates.

✓ Plumbing, ductwork and wire connections. Check the pipe connections for fluid leaks. Examine duct connections and seals. Also make sure that all wire connections are tight.

✓ Roof penetrations. Flashing and sealant around the roof penetration should be checked to see that it’s in a good shape.

✓ Collector shading. Check for shading of the collectors on annual basis as this may greatly affect their performance.

✓ Support structures. Examine all bolts and nuts which connects the support structures to the collectors for tightness.

✓ Heat transfer fluids. Anti freeze solutions in liquid solar heating collectors will have to be replaced periodically. And this right here is a task that’s best handled by a licensed technician.

Commercial solar panels installation companies are everywhere. However, it’ll be a great mistake to think finding one nearby for your project would be the least of your worries, as both cost and reliability comes into question. This is even more worrisome when you’re fully aware that your solar system potentials can only be fully maximized depending on how well it’s installed and how good your installer is. If you’re also facing the same challenge, then you’ve come to the right place. In this article, we’ll share with you some tips on how to choose a nearby professional and reliable commercial solar panel installer who’ll ensure you get immense value for every penny spent. Let’s take a look!

• Ask for recommendations. Personal recommendations is always the best way to go, when looking for a commercial solar panel installer or any other tradesperson for that matter. Installation of a commercial solar system is a major undertaking which comes with a lot of costs, so if you’re going to do it the least you can do is ensure you do it right. Carry out your research, ask friends and family, neighbours and loved ones if the know of any reliable commercial solar panel installer in the local area. If they have one they’ve used, you can request for the cost, quality of the job done, the duration of the project and any other detail you feel you should know.
• Internet. In modern times, you’ll hardly find a progressive-minded business without an online presence. As a result, finding a service on the internet is as simple as it gets. A simple Google search have been helping people find their desired service providers with relative ease for so long. Or use the Quotatis directory to find a commercial solar installer. To get the right commercial solar panel installer online, it’s advisable to check their reviews as well as testimonials before moving forward.

To have your solar panels working at full strength at all times is crucial as this can go a long way to help you reduce your energy bill. In order to achieve this, you simply can’t afford to ignore having them regularly cleaned and free from all sorts of dirt, dust, debris, pollen, bird droppings and the likes. Now it’s quite reasonable to think rain or wind should be able to get the job done, but unfortunately this is not so. What solar panels need is a proper clean which you can decide to do by yourself or call in a qualified professional – the latter which is strongly recommended.

Cleaning of solar panels has to do with working at heights which can be very dangerous especially if you don’t have enough confidence to pull it off. And even if you have zero phobia for heights, solar panel cleaning requires experience as well as some specialized skills and tools possessed by the professionals. However, the question here is, how often should solar panels be cleaned to keep them operating at optimal efficiency?

Well, according to the manufacturers, solar panels should be cleaned twice a year. However, if this is something that you feel is not achievable by you, then you should at least give then an annual clean. The best or most advisable time to do this during the year is at the end of the summer months. This will ensure that you have a fully functioning solar array which is ready and prepared to withstand whatever the cold period throws at you. At the end of the day, you’d have them looking spotless clean while also working at full strength and reducing your energy bills.

Unlike the photovoltaic (PV) power which works to turn a part of the electromagnetic radiation of the sun directly to electrons and electricity, a solar thermal can simply be referred to as the absorption of the sun’s heat for human use. As a result, the solar thermal has a wider range of uses than the PV does in several ways. This is due to the fact that the sun’s heat can be absorbed and transported via a medium and the stored energy incorporated for several great purposes such as to heat water, to heat and cool a home or living space, to prepare a meal as well as to generate electricity. All these functions are useful for both residential and commercial spaces.

There are generally three different ranges of solar thermal energy that are being used which includes the low temperature ( for heating, cooling as well as ventilation), the mid temperature ( used for preparing meals, heating hot water and the likes) as well as the high temperature ( used for generating electricity). To focus more on generating electricity, there are a wide array of ways through which the sun’s heat can be directed at creating electricity via a heat exchanger which operates to super heat water or inert gas to power an electricity- generating plant or to produce electricity via a Stirling engine.

In order to increase their output or make them more efficient, evacuated glass tubes are used to encircle the tubes which in turn helps them to collect more heat energy while also protecting them from re-radiating the heat energy absorbed. The trough are normal positioned north to south as well as to keep tabs on the travels of the sun throughout the day.