Find a Solar Panel Installer you can trust in Grimsby.

1. After the installer’s measured up, given you an estimated output and recommended some systems for you, they’ll arrange date to come to your home to install the solar thermal panels. They’ll also let you know if any scaffolding will be required.
2. Next, they will start to fit the panels, or collectors, to your roof. Stainless steel brackets will be provided with the system and they will remove your roof tiles or slates to attach the brackets to the rafters. They’ll then replace the tiles and add waterproof flashing to ensure you don’t get any roof leaks, and add the frame.
3. If you’ve chosen evacuated tube solar thermal panels, the installer will bolt the heat transfer unit to the top of the frame but not install the tubes until nearer the end. This is because the tubes start to transfer heat to the exchanger immediately, and when everything is unconnected this could damage the unit.
4. If you don’t need a new boiler with your installation, a new dual coil water cylinder, pump and system control system will be fitted. It’s best in a loft or upper floor of your home.
5. A new thermal store or hot water tank that will store the heat provided by the solar system is much larger than a standard tank but it may fit in the spot of your old one. The installer will ensure that it’s connected to the mains cold water, your other heating source (such as a gas boiler or biomass boiler), immersion heater, temperature sensors and the solar collectors themselves.
6. Next they will install the pumping station, usually near the water tank. The expansion tank will be installed on the solar thermal loop, which is usually nearby. Its job is to prevent pressure changes that could damage the system.
7. You’ll get a heat generation meter which must be MCS-certified if you want to take advantage of the RHI, and any control equipment that comes with the system will be installed.
8. The installers will then bring the system to pressure by pumping the heat transfer liquid into the system up to a pressure of around 2 bar.
9. Finally, your MCS-registered installer will register your solar thermal system so you can apply for RHI payments of up to £525 per year.
So that’s the process of installing solar thermal panels. Remember – it's always best to use a professional to install any kind of renewable technology.

In a similar way to other major home improvement projects, some specific requirements must be met to allow for the installation of solar panels. The main reason why these standards and regulations were established is to minimize the risk of the solar system becoming an issue or potential hazard in the unforeseeable future. So if you’re thinking about buying and fitting new solar panels, you’ll probably want to know whether or not you’ll require to submit a planning permission application for approval before you can proceed.

Generally, solar panels are covered under what’s called “Permitted Development” which gives you the freedom to install your solar panels without having to apply for a planning permission. However, there are some exceptions to this rule. These exceptions include if your house is a listed building or if your house is located within a conservation area. In these exceptional cases, it’s possible that you’ll need to apply for a planning permission, but this will largely depend on the discretion of your Local Planning Authority. What’s more? Solar panels are usually subjected to normal building regulations which includes examining the roof to make sure that it can support the additional weight. You can call in a MCS certified installer to carry out this check for you.

In order to install your solar PV on your roof, you must follow these guidelines:

✓ Your solar panels shouldn’t go beyond the highest point of the roof (excluding chimneys).

✓ The solar panels shouldn’t project beyond 200mm off the roof’s edge.

✓ The solar panels should be removed once they’re no longer used to produce electricity

✓ The solar panels should be installed such that the area and building’s appearance change is minimized.

If you’re looking to purchase and install a solar system for your home or property, then knowing the amount of energy a solar panel can produce can go a long way to help you determine just how much solar panels that’ll be needed to power your entire house. In this article, we’ll give you an idea of the amount of energy that can be generated by a solar panel to help you make informed decisions going ahead.

First and foremost, you should note that each and every solar panel is rated by how much direct current power they’re able to generate under standard testing conditions. The output of a solar panel is given in watts units (W) and it stands for the theoretical power generation of the panel under direct sunlight as well as temperature conditions. Generally, several domestic solar panels possesses power output ratings which ranges from 250 watts to 400 watts. And as you would have expected, the higher power ratings are preferable when compared to the lower power ratings. What’s more? The total wattage of your solar panels will greatly influence a major part of your overall solar system cost.

Assuming you’re able to get just about 5 hours of direct sunlight every day, you can determine the output of your solar panel in this way - 5 hours x 290 watts ( wattage example of a premium solar panel) = 1450 watts-hours or approximately 1.5 kilowatts per hour (kWh). hence, the individual solar panel output in your array should be able to generate about 500 to 550 kWh of energy every year. This is sufficient energy to power some small appliances without problems.

If you want to test your solar panel system to see if it’s working properly or just to see what output it’s giving, you can do this using a multimeter to measure current, or amps, and voltage.

Before you start, you’ll need to find the voltage (v) and current (A) ratings of your panel. You should be able to find them on the back of the panel. You should also make sure that it’s a nice clear, sunny day to get the best readings out of your panel. You should also check that it’s safe to be up on your roof!

To measure open circuit voltage, you’ll need to make sure that your solar panel is completely disconnected from your system’s regulator and battery (if you have one). Angle the panel towards the sun, and ensure that your multimeter is set to measure volts. Measure the voltage between the positive and negative terminals by connecting the negative contact on the voltmeter to the negative on the panel and the positive contact on the voltmeter to the positive on the panel.

Then, you can move on to the short circuit current. Follow the same steps as the open circuit voltage, but ensure that your multimeter is set at 10A to start with.

Only try to test your solar panel if it’s safe to do so. If your roof isn’t accessible without scaffolding or specialist equipment, consider speaking to an MCS-registered solar company about your concerns. They may recommend that they come to service your solar panel system.

Most domestic solar thermal panels do not need planning permission and are covered by permitted development rights. There are restrictions on the size and location of these systems. If you live in a conservation area or listed building, or want to install a very large solar thermal system, check with your local authority to see if you will need planning permission.

How Many Solar Panels And Batteries To Power A House?

Do you wish to know the number of solar panels and batteries sufficient for a house? Well, this is a frequently asked question in the solar world which would be very difficult to provide an accurate answer. This is basically down to the fact that all homes are unique with different sizes as well as amount of daily energy requirements. As a result, the number of solar panels and batteries needed would be unique to the house in question. However, we’ll consider the varying influencing factors that will go a long way to help calculate the number of panels and batteries needed to power a house.

First and foremost, let’s take a look at the solar panels. You’d have to start here by putting into consideration all household appliances that makes use of power in the house to get a good idea of how many that’ll be needed.

• How Many Watts Is Being Used In The House On A Daily Basis?

To determine this, simply go through your utility bill for kilowatt-hours (kWh). This varies amongst homes and being able to identify your daily average energy usage will assist you in getting your solar needs.

• What Is The Number Of The Peak Sunlight Hours At The House’s Location?

Having in mind that the solar panels only work when under direct sunlight, the first step to determine the peak sunlight hours. Once determined, you can then multiply the figure in hours by the house’s hourly energy usage and divide by the solar panel’s wattage.

Overall for a 1500 square foot house, the number of solar panels that’ll be required should fall around 15 to 18.

Meanwhile for batteries, there are also some factors to be considered to determine the number of batteries that is required to power a house. These factors include the house’s power or electricity usage, the period of time in which the battery will be used as well as the battery’ specifications.