Find a Solar Panel Installer you can trust in Driffield.

Most domestic solar thermal panels do not need planning permission and are covered by permitted development rights. There are restrictions on the size and location of these systems. If you live in a conservation area or listed building, or want to install a very large solar thermal system, check with your local authority to see if you will need planning permission.

1. After the installer’s measured up, given you an estimated output and recommended some systems for you, they’ll arrange date to come to your home to install the solar thermal panels. They’ll also let you know if any scaffolding will be required.
2. Next, they will start to fit the panels, or collectors, to your roof. Stainless steel brackets will be provided with the system and they will remove your roof tiles or slates to attach the brackets to the rafters. They’ll then replace the tiles and add waterproof flashing to ensure you don’t get any roof leaks, and add the frame.
3. If you’ve chosen evacuated tube solar thermal panels, the installer will bolt the heat transfer unit to the top of the frame but not install the tubes until nearer the end. This is because the tubes start to transfer heat to the exchanger immediately, and when everything is unconnected this could damage the unit.
4. If you don’t need a new boiler with your installation, a new dual coil water cylinder, pump and system control system will be fitted. It’s best in a loft or upper floor of your home.
5. A new thermal store or hot water tank that will store the heat provided by the solar system is much larger than a standard tank but it may fit in the spot of your old one. The installer will ensure that it’s connected to the mains cold water, your other heating source (such as a gas boiler or biomass boiler), immersion heater, temperature sensors and the solar collectors themselves.
6. Next they will install the pumping station, usually near the water tank. The expansion tank will be installed on the solar thermal loop, which is usually nearby. Its job is to prevent pressure changes that could damage the system.
7. You’ll get a heat generation meter which must be MCS-certified if you want to take advantage of the RHI, and any control equipment that comes with the system will be installed.
8. The installers will then bring the system to pressure by pumping the heat transfer liquid into the system up to a pressure of around 2 bar.
9. Finally, your MCS-registered installer will register your solar thermal system so you can apply for RHI payments of up to £525 per year.
So that’s the process of installing solar thermal panels. Remember – it's always best to use a professional to install any kind of renewable technology.

If you want to connect solar panels to a battery, it’s likely that it’s because you want to make sure that you don’t waste any electricity when your solar panels are generating energy but you’re not around to use it. Batteries are particularly useful for homeowners that have solar panels but are out during daylight hours; with a solar battery system, your solar panels will feed the electricity they generate into the battery for you to use when you get home.

If you want to connect your solar panels to a battery, the best thing to do is to get in touch with an MCS-registered company who can talk you through your options. There are different size batteries and the size that’s suitable for you will depend on how much electricity you plan to store and how large your solar panel system is. Some of the top brands of battery storage system include Tesla, SunPower and SolarEdge. If you want to be able to take advantage of selling electricity back to the grid through the Smart Export Guarantee (SEG), it’s worth getting an MCS-registered company to install your battery for you, as you may not be eligible for payments if you connect your solar panels to a battery yourself.

You should also consider whether your solar panel system is a ‘storage ready’ solar system. Today, most systems will be, since battery storage is becoming much more common. This means that your solar panel system will have an inverter that can easily integrate a battery. If this is the case, you should be able to purchase the battery you want and follow the manufacturer’s instructions to install it.

However, it’s worth bearing in mind that electricity is extremely dangerous when handled incorrectly. If something goes wrong, you could electrocute yourself or cause a fire. If your solar panels and battery cause a fire, it’s unlikely that your home insurance company would pay out if you connect the battery yourself. That's why it’s best to ask a reputable installer with all the correct qualifications to connect your solar panels to a battery for you.

It’s important to get the right size solar panel system for your commercial property. Solar panels are usually installed on pitched roofs, although they can be fitted on stands on the ground if you have some unused outdoor space. The more panels you install, the more power you’ll generate, but there’s no point buying more panels than you have space for.

Solar panel system sizes are measured in kW. 4-10kW solar panel systems are usually too big for domestic properties but are ideal for smaller commercial properties. Here’s an idea of how many panels and space you’ll need for a few different system sizes:

System size, Number of panels, Area required (approximate)

4kW, 16, 23m²

6kW, 24, 35m²

8kW, 32, 46m²

10kw, 40, 58m²

Bear in mind that solar panels can’t be less than 30cm away from a roof edge, so you’ll need more space than the area that the panels take up.

The lifetime of a solar panel depends on its quality and age. Generally, the older a solar panel gets, the less efficient it becomes. The majority of modern solar panels come with 20-30 year warranties, which means that they’ll stay at a good efficiency level for at least this long. Some panels can stay efficient for as long as 40 years, while others won’t last this long.

Yes – solar panels do work in winter. Contrary to popular belief, solar panels can still work under daylight, even if it's not hot. Of course, they won’t generate as much electricity as they would during the summer months, as the days are shorter, but they will still generate electricity during those daylight hours.

Once you know how solar panels work, it’s easy to understand why solar panels work in the winter. Solar panels are made up of photovoltaic (PV) cells, which are units usually made out of silicon. These cells contain electrons that create energy when light hits them. The cell can then convert this energy into usable electric current and into your system to be used around the home.

Although it might seem strange, solar PV cells can actually work better when it’s cold. Too much heat around the cell can cause it to be inefficient, due to the difference in energy between the energy from the sunlight and the electrons in the solar cell. During cold weather, the difference between them is higher, so more

The higher the energy difference between the two sets of energy sources, the more power that the cell can produce when it’s struck by light. Of course, the downside is that there are fewer daylight hours in the winter, so you’ll still see a drop in energy production – but at least you know that your solar panels are still working efficiently. The other thing to bear in mind is that obstructions like snow and lots of cloud cover will impact the amount of electricity your solar panels will produce. Luckily the UK doesn’t get too much heavy snow, so any snow that does settle on the panels will melt quickly. As for cloud cover, even on exceptionally cloudy days your panels will still generate some electricity – just not as much as they would on a clear day.

After making the very important business decision to go solar, you may also want to know just how long it’ll take to complete the installation process and start generating electricity. After all, generating electricity is the main reason you made the switch to solar system. In this post, we’re going to provide you with in depth details on how long it takes to install solar panels as well as the factors that may affect that time.

The entire process of solar panels installation and getting them approved isn’t an overnight process. You’ll have to wait for periods for each step of the process whereby one must be completed before moving to the next. The time required to complete each step can, however, vary largely depending on your location, the type of solar panels you opt for, the solar company you hire as well as the number of people that’ll be making the installation. Here are the steps to a solar system installation and the estimated time each are expected to take:

• Site assessment. Once you chosen your solar company, the first step would be to have a solar professional from the company to visit the site to examine the roof and other features so as to make sure that they’re able to support a solar system. From the initial contact to scheduling the site visit, this step can take up to 1 to 2 weeks
• Local permitting. This involves getting the right permits from your local authorities. This can take up to 3 to 6 or more weeks.
• Solar system design. This may take up to a week or two depending on whether or not you need design approval and also where the parts are coming from
• Installation. This step can take a week or two depending on the size af your solar panel and roof.
• Inspection. This step can take up to a week depending on where you reside and how quickly the inspector can visit.
• Utility connection. Depending on your utility company, this step can take up to 2 weeks.