Find a Solar Panel Installer you can trust in Strathcarron.

1. After the installer’s measured up, given you an estimated output and recommended some systems for you, they’ll arrange date to come to your home to install the solar thermal panels. They’ll also let you know if any scaffolding will be required.
2. Next, they will start to fit the panels, or collectors, to your roof. Stainless steel brackets will be provided with the system and they will remove your roof tiles or slates to attach the brackets to the rafters. They’ll then replace the tiles and add waterproof flashing to ensure you don’t get any roof leaks, and add the frame.
3. If you’ve chosen evacuated tube solar thermal panels, the installer will bolt the heat transfer unit to the top of the frame but not install the tubes until nearer the end. This is because the tubes start to transfer heat to the exchanger immediately, and when everything is unconnected this could damage the unit.
4. If you don’t need a new boiler with your installation, a new dual coil water cylinder, pump and system control system will be fitted. It’s best in a loft or upper floor of your home.
5. A new thermal store or hot water tank that will store the heat provided by the solar system is much larger than a standard tank but it may fit in the spot of your old one. The installer will ensure that it’s connected to the mains cold water, your other heating source (such as a gas boiler or biomass boiler), immersion heater, temperature sensors and the solar collectors themselves.
6. Next they will install the pumping station, usually near the water tank. The expansion tank will be installed on the solar thermal loop, which is usually nearby. Its job is to prevent pressure changes that could damage the system.
7. You’ll get a heat generation meter which must be MCS-certified if you want to take advantage of the RHI, and any control equipment that comes with the system will be installed.
8. The installers will then bring the system to pressure by pumping the heat transfer liquid into the system up to a pressure of around 2 bar.
9. Finally, your MCS-registered installer will register your solar thermal system so you can apply for RHI payments of up to £525 per year.
So that’s the process of installing solar thermal panels. Remember – it's always best to use a professional to install any kind of renewable technology.

If you’re considering getting a solar thermal system, one of the first things that comes to mind is the possibility of the system functioning properly during the cold months. The short and simple answer to this question is yes, a solar thermal system works in the winter. However, the downside here is that it’ll be a lot less efficient when compared to how it operates during the warmer months or summer. As a result of this fact, you’ll likely need to rely more on your boiler, immersion heater or any other backup heating system during this period as your solar thermal system will fail to contribute as much as it does during the warmer months. So what exactly is the reason why solar thermal is less effective and less efficient in the winter period? Let’s have a look!

As you know, solar thermal system banks on the sun’s energy to heat the water for your home’s use. During the cold months or winter, the sunlight becomes a lot less available when compared to the warmer months, as a result, there’s less sunlight that’s available to be used for its solar energy. And even more so at the periods when the days are shorter or skies are clearly overcast.

Also having a great impact on a solar thermal system’s output is heavy snow. Flat plate collectors normally have the capacity to cope better during snowy conditions as the light that’s able to travel through the snow will heat up the absorber plate - thereby making the snow slide off more quickly. However, the case is contrary with evacuated tube collectors which possesses a form of vacuum insulation that’s crafted to minimize the loss of heat, meaning they can’t generate heat to melt and cause the snow to slide off in a similar way.

Are you thinking of installing solar thermal systems in your home or property and wondering exactly how it works to generate electricity? Regardless of your motive, in this article you’ll learn in simple details how solar thermal is how solar thermal doesn't provide electricity for your home.

If you are looking to generate electricity for your home then Solar PV are able to generate electricity simply by absorbing and focusing sunlight in such a way to create a temperature level that’s high enough to generate the much needed electricity. There are two main components that comes with the solar energy collectors of each. These two components include, the reflectors ( mirrors), which works to absorb and concentrate the sunlight onto a receiver. In several types of the solar thermal power systems, a heat transfer fluid is then heated and distributed in the receiver so as to generate steam. Once the steam as been produced, it’s then transported to the turbine where it’s turned into a mechanical energy, which in turn powers the generator to produce electricity.

Solar thermal power or electric systems are usually embedded with a tracking system which keeps the sunlight concentrated on the receiver all day long as the sun changes position in the sky. They also come with a wide array of collectors which works of distribute the heat absorbed to a turbine as well as the generator. A lot of solar thermal power facilities will gave two or more plants with different arrays and generators.

Solar thermal power systems can also have a thermal energy storage system component whose work is to permit the solar collector system to heat an energy storage system during the day while energy storage system’s generated heat is incorporated in the production of electricity at night or during a cloudy weather when there’s not much sunlight.

Commercial solar panels installation companies are everywhere. However, it’ll be a great mistake to think finding one nearby for your project would be the least of your worries, as both cost and reliability comes into question. This is even more worrisome when you’re fully aware that your solar system potentials can only be fully maximized depending on how well it’s installed and how good your installer is. If you’re also facing the same challenge, then you’ve come to the right place. In this article, we’ll share with you some tips on how to choose a nearby professional and reliable commercial solar panel installer who’ll ensure you get immense value for every penny spent. Let’s take a look!

• Ask for recommendations. Personal recommendations is always the best way to go, when looking for a commercial solar panel installer or any other tradesperson for that matter. Installation of a commercial solar system is a major undertaking which comes with a lot of costs, so if you’re going to do it the least you can do is ensure you do it right. Carry out your research, ask friends and family, neighbours and loved ones if the know of any reliable commercial solar panel installer in the local area. If they have one they’ve used, you can request for the cost, quality of the job done, the duration of the project and any other detail you feel you should know.
• Internet. In modern times, you’ll hardly find a progressive-minded business without an online presence. As a result, finding a service on the internet is as simple as it gets. A simple Google search have been helping people find their desired service providers with relative ease for so long. Or use the Quotatis directory to find a commercial solar installer. To get the right commercial solar panel installer online, it’s advisable to check their reviews as well as testimonials before moving forward.

Solar panels are made up of photovoltaic (PV) cells. These cells are made from silicon semiconductors, which absorb sunlight and convert it into electricity.

There are three main types of PV cell: monocrystalline solar cells, polycrystalline solar cells, and thin film solar cells. Monocrystalline cells are usually the most efficient and expensive, and thin film solar cells are the cheapest and least efficient. These are all made from silicone, but are manufactured in different ways.

Like every other systems in your home, solar hot water systems will require periodic inspections as well as a regular maintenance in order to keep it running as efficiently as it should. Not only that, the various components will also require either repair or replacement from time to time. It’ll also be proactive to take the necessary precautions so as to prevent worrying issues like corrosion, scaling or freezing.

Is it a task you can handle on your own? Well, there are some inspections and maintenance activities you should be able to handle on your own, however, you’ll also require a qualified technician to carry out the more technical or complicated tasks. You should also take note that it may actually be more cost effective to have some systems replaced, shut off or removed completely than having it repaired. Here are some of the essential inspections that should be carried out on solar system components. They include:

✓ Collector soiling. Periodic cleaning of your collectors is important especially in dry and dusty climates.

✓ Plumbing, ductwork and wire connections. Check the pipe connections for fluid leaks. Examine duct connections and seals. Also make sure that all wire connections are tight.

✓ Roof penetrations. Flashing and sealant around the roof penetration should be checked to see that it’s in a good shape.

✓ Collector shading. Check for shading of the collectors on annual basis as this may greatly affect their performance.

✓ Support structures. Examine all bolts and nuts which connects the support structures to the collectors for tightness.

✓ Heat transfer fluids. Anti freeze solutions in liquid solar heating collectors will have to be replaced periodically. And this right here is a task that’s best handled by a licensed technician.

Are you thinking about installing a solar thermal system in your home? If yes, the you’d most likely be wondering the exact amount the system is going to cost. Well, you’re not alone. This is one of the most common question when it comes to solar thermal systems and we aim to answer that in this article. So let’s get started!

Unfortunately, the cost of a solar thermal system can’t be given in a single, accurate answer as they vary widely. However, when getting a new solar thermal system, you can expect to pay a sum within the range of £3000 to £6000 ( this includes a lowered VAT rate of 5 percent). The figures provided takes into account the installation costs as well as all the parts ( such as control panel, solar collectors, hot water tank and pipes).

To determine the price of your system, the quality and type of the panels matter. For instance, according to the Solar Trade Association, a properly insulated twin coil cylinder system would be priced at around £4500. in the same tone, it’s also possible to get DIY solar thermal kits that includes all the required hardware which will cost within the range of £1500 to £250. This however, may not be eligible for government support. In order to benefit from the RHI, your system must be fitted by a MCS accredited installer.

The varying prices of the solar thermal system’s initial cost is based on the specification of each individual house. For example, in situations where the building is having complicated water system, the plumbing cost is expected to increase which will have a serious impact on the overall cost of the solar thermal power system.