Find a Solar Panel Installer you can trust near you.

Obviously the performance of a solar thermal system will vary depending on the location of the home, the insulation of the property, and your own hot water requirements. Solar thermal panels are capable of providing all of your hot water requirements from April to September. They will still make a contribution to your hot water needs for the rest of the year, but in general you will need a backup system to further heat the water in the colder months.

1. After the installer’s measured up, given you an estimated output and recommended some systems for you, they’ll arrange date to come to your home to install the solar thermal panels. They’ll also let you know if any scaffolding will be required.
2. Next, they will start to fit the panels, or collectors, to your roof. Stainless steel brackets will be provided with the system and they will remove your roof tiles or slates to attach the brackets to the rafters. They’ll then replace the tiles and add waterproof flashing to ensure you don’t get any roof leaks, and add the frame.
3. If you’ve chosen evacuated tube solar thermal panels, the installer will bolt the heat transfer unit to the top of the frame but not install the tubes until nearer the end. This is because the tubes start to transfer heat to the exchanger immediately, and when everything is unconnected this could damage the unit.
4. If you don’t need a new boiler with your installation, a new dual coil water cylinder, pump and system control system will be fitted. It’s best in a loft or upper floor of your home.
5. A new thermal store or hot water tank that will store the heat provided by the solar system is much larger than a standard tank but it may fit in the spot of your old one. The installer will ensure that it’s connected to the mains cold water, your other heating source (such as a gas boiler or biomass boiler), immersion heater, temperature sensors and the solar collectors themselves.
6. Next they will install the pumping station, usually near the water tank. The expansion tank will be installed on the solar thermal loop, which is usually nearby. Its job is to prevent pressure changes that could damage the system.
7. You’ll get a heat generation meter which must be MCS-certified if you want to take advantage of the RHI, and any control equipment that comes with the system will be installed.
8. The installers will then bring the system to pressure by pumping the heat transfer liquid into the system up to a pressure of around 2 bar.
9. Finally, your MCS-registered installer will register your solar thermal system so you can apply for RHI payments of up to £525 per year.
So that’s the process of installing solar thermal panels. Remember – it's always best to use a professional to install any kind of renewable technology.

• Don’t buy cheap solar panels – while it might seem tempting, make sure you choose MCS-certified solar panels. Any reputable installer will recommend high quality solar panels, which is another reason to have them professionally installed rather than doing it yourself.
• Ensure that your installer uses non-combustible mounting systems and frames.
• Check your system regularly for signs of pests gnawing through cables.
• Keep your solar panel system regularly maintained with proper testing and servicing carried out as recommended by your installer.
• If something doesn’t look right to you, get in touch with your installer and ask – they should be more than happy to help.

If you’re looking to purchase and install a solar system for your home or property, then knowing the amount of energy a solar panel can produce can go a long way to help you determine just how much solar panels that’ll be needed to power your entire house. In this article, we’ll give you an idea of the amount of energy that can be generated by a solar panel to help you make informed decisions going ahead.

First and foremost, you should note that each and every solar panel is rated by how much direct current power they’re able to generate under standard testing conditions. The output of a solar panel is given in watts units (W) and it stands for the theoretical power generation of the panel under direct sunlight as well as temperature conditions. Generally, several domestic solar panels possesses power output ratings which ranges from 250 watts to 400 watts. And as you would have expected, the higher power ratings are preferable when compared to the lower power ratings. What’s more? The total wattage of your solar panels will greatly influence a major part of your overall solar system cost.

Assuming you’re able to get just about 5 hours of direct sunlight every day, you can determine the output of your solar panel in this way - 5 hours x 290 watts ( wattage example of a premium solar panel) = 1450 watts-hours or approximately 1.5 kilowatts per hour (kWh). hence, the individual solar panel output in your array should be able to generate about 500 to 550 kWh of energy every year. This is sufficient energy to power some small appliances without problems.

The lifetime of a solar panel depends on its quality and age. Generally, the older a solar panel gets, the less efficient it becomes. The majority of modern solar panels come with 20-30 year warranties, which means that they’ll stay at a good efficiency level for at least this long. Some panels can stay efficient for as long as 40 years, while others won’t last this long.

If you want to test your solar panel system to see if it’s working properly or just to see what output it’s giving, you can do this using a multimeter to measure current, or amps, and voltage.

Before you start, you’ll need to find the voltage (v) and current (A) ratings of your panel. You should be able to find them on the back of the panel. You should also make sure that it’s a nice clear, sunny day to get the best readings out of your panel. You should also check that it’s safe to be up on your roof!

To measure open circuit voltage, you’ll need to make sure that your solar panel is completely disconnected from your system’s regulator and battery (if you have one). Angle the panel towards the sun, and ensure that your multimeter is set to measure volts. Measure the voltage between the positive and negative terminals by connecting the negative contact on the voltmeter to the negative on the panel and the positive contact on the voltmeter to the positive on the panel.

Then, you can move on to the short circuit current. Follow the same steps as the open circuit voltage, but ensure that your multimeter is set at 10A to start with.

Only try to test your solar panel if it’s safe to do so. If your roof isn’t accessible without scaffolding or specialist equipment, consider speaking to an MCS-registered solar company about your concerns. They may recommend that they come to service your solar panel system.