Find a Solar Panel Installer you can trust in Caledon.

If you want to test your solar panel system to see if it’s working properly or just to see what output it’s giving, you can do this using a multimeter to measure current, or amps, and voltage.

Before you start, you’ll need to find the voltage (v) and current (A) ratings of your panel. You should be able to find them on the back of the panel. You should also make sure that it’s a nice clear, sunny day to get the best readings out of your panel. You should also check that it’s safe to be up on your roof!

To measure open circuit voltage, you’ll need to make sure that your solar panel is completely disconnected from your system’s regulator and battery (if you have one). Angle the panel towards the sun, and ensure that your multimeter is set to measure volts. Measure the voltage between the positive and negative terminals by connecting the negative contact on the voltmeter to the negative on the panel and the positive contact on the voltmeter to the positive on the panel.

Then, you can move on to the short circuit current. Follow the same steps as the open circuit voltage, but ensure that your multimeter is set at 10A to start with.

Only try to test your solar panel if it’s safe to do so. If your roof isn’t accessible without scaffolding or specialist equipment, consider speaking to an MCS-registered solar company about your concerns. They may recommend that they come to service your solar panel system.

If you’re considering getting a solar thermal system, one of the first things that comes to mind is the possibility of the system functioning properly during the cold months. The short and simple answer to this question is yes, a solar thermal system works in the winter. However, the downside here is that it’ll be a lot less efficient when compared to how it operates during the warmer months or summer. As a result of this fact, you’ll likely need to rely more on your boiler, immersion heater or any other backup heating system during this period as your solar thermal system will fail to contribute as much as it does during the warmer months. So what exactly is the reason why solar thermal is less effective and less efficient in the winter period? Let’s have a look!

As you know, solar thermal system banks on the sun’s energy to heat the water for your home’s use. During the cold months or winter, the sunlight becomes a lot less available when compared to the warmer months, as a result, there’s less sunlight that’s available to be used for its solar energy. And even more so at the periods when the days are shorter or skies are clearly overcast.

Also having a great impact on a solar thermal system’s output is heavy snow. Flat plate collectors normally have the capacity to cope better during snowy conditions as the light that’s able to travel through the snow will heat up the absorber plate - thereby making the snow slide off more quickly. However, the case is contrary with evacuated tube collectors which possesses a form of vacuum insulation that’s crafted to minimize the loss of heat, meaning they can’t generate heat to melt and cause the snow to slide off in a similar way.

If you’re looking to install some new solar panels in your home or property, then you’d probably want to know how it works. This is one of the most frequent questions asked by homeowners when it comes to solar panels and in this article we aim to give you a good insight on the operations of solar panels. Let’s have a look!

Generally, solar panels work by absorbing the energy of the sun and then converting it into electricity. It functions by allowing photons from the rays of the sun release the electrons free from atoms within the photovoltaic or solar cells in order to produce a flow of electricity. There are several solar cells that are connected together ( usually 60 or 72 ) in each panel. Individual cells comprises both a negative layer and a positive one which combines perfectly to create an electrical field in which the energy is generated.

The boron that’s within the bottom layer generates the positive charge, while the phosphorous found in the silicon layer produces the negative charge. In order to convert the sun’s rays into the energy that’s going to be transported from the panels to the inverter, the two field will interact with one another.

In other words, solar panels work by turning photons from the sunlight into direct current which is transmitted to the inverter. Once it gets to the inverter, it’s then translated to alternating current and send this current to to your electric box which powers the entire home. If you do not wish to reduce the high bills that’s associated with renting power from the grid, the solar energy system is an efficient and affordable way to achieve this aim.

With the numerous benefits that comes with the installation of solar panels, it should not be an option for just a few just because of the size and/or pitch of their roof. A number of individuals with flat roofs decide against solar panels due to the fact that they believe that the panels can’t be installed due to the lack of direct sunlight. However, in truth, this thought is absolutely incorrect. This is because it is actually very possible to fit solar panels on flat roofs and you can also benefit from a good amount of electricity that’ll be generated over time. In this post, we’re going to look at the possibilities involved in the installation of commercial solar panels on a flat roof. Let’s get started!

In reality, flat roof solar systems are mostly found on commercial buildings as their roof is typically made to be flat. Although, it’s important to note that it’s absolutely possible for them to be fitted on domestic properties too. The type of solar array that’s installed makes use of the same type of solar panel as a conventional system, however, there are some considerations that’ll have to be made moving forward. The array must be able to self clean during the rainy season while also avoiding damage whenever there’s a strong wind. The installation company you choose should take the pitch of the system into account, so as to make sure that its able to capture as much energy from the sun as possible. And that’s exactly why you should consider the use of thin film solar cells which are very flexible and moves with the sun as the day goes by, securing as much sunlight as possible as its always in direct light.

Are you currently weighting the possibilities of adding a solar system to your commercial building? With lots of commercial property owners in the UK using solar now, many more are gradually coming to terms with the numerous benefits they stand to derive by getting one. Therefore, if you’re thinking about adding the system to your commercial building but do not know where to start, you’ve come to the right place.

In this post, our aim is to help you calculate the number of solar panels you’ll need to power your entire commercial building. Starting from the panels, you can begin by taking into account everything that makes use of power in your commercial building to get a good idea of how many you’ll need.

• To get started, you’ll have to determine the number of watts used by your commercial building. To get this, you simply have to go through your utility bill for kilowatt-hours (kWh). This varies amongst buildings and being able to identify your daily average energy usage will assist you in getting your solar panel needs.
• Once done, you’ll also have to determine the peak sunlight hours - having in mind that the solar panels only work when under direct sunlight. Once determined, you can then multiply the figure in hours by your home’s hourly energy usage and divide by your selected solar panel’s wattage.

In general, a medium-sized commercial building making use of an average amount of electricity will require about 70 average quality solar panels so as to cover its entire electricity needs. These are, however, just averages, so yours could be more or less so getting the idea is vital here.

Just like other major house improvement projects, some specific requirements must be met to allow for the installation of solar panels on commercial buildings. The main reason why these standards and regulations were established is to minimize the risk of the solar system becoming an issue or potential hazard in the unforeseeable future. So if you’re thinking about buying and fitting new solar panels, you’ll probably want to know whether or not you’ll require to submit a planning permission application for approval before you can proceed.

Fortunately, the installation of solar panels on commercial buildings may be “permitted development which mean you won’t have to apply to the Local Planning Authority for planning permission. There are, however, some important limits and conditions which must be put into consideration in order to benefit from these permitted development rights. Some of the limitations include:

• The solar panels must be installed on a wall or pitched roof that should project at a maximum of 200mm from the surface of the wall or roof slope.
• Equipment placed on a roof should not be within one metre of the external edge of that roof.
• Equipment mounted on a wall must not be within one metre of a junction of that wall with another wall or with the roof of the building
• If the equipment is on the roof of a building, the capacity for generation of electricity across the entire site must not be more than 1 megawatt.
• In the situation whereby the panels are installed on a flat roof, the highest part of the equipment should not exceed one metre above the highest part of the roof.

In general, obtaining a planning permission is very important and as such, you must discuss your position with your chosen installation company before you proceed.