Find a Solar Panel Installer you can trust in County Londonderry.

1. After the installer’s measured up, given you an estimated output and recommended some systems for you, they’ll arrange date to come to your home to install the solar thermal panels. They’ll also let you know if any scaffolding will be required.
2. Next, they will start to fit the panels, or collectors, to your roof. Stainless steel brackets will be provided with the system and they will remove your roof tiles or slates to attach the brackets to the rafters. They’ll then replace the tiles and add waterproof flashing to ensure you don’t get any roof leaks, and add the frame.
3. If you’ve chosen evacuated tube solar thermal panels, the installer will bolt the heat transfer unit to the top of the frame but not install the tubes until nearer the end. This is because the tubes start to transfer heat to the exchanger immediately, and when everything is unconnected this could damage the unit.
4. If you don’t need a new boiler with your installation, a new dual coil water cylinder, pump and system control system will be fitted. It’s best in a loft or upper floor of your home.
5. A new thermal store or hot water tank that will store the heat provided by the solar system is much larger than a standard tank but it may fit in the spot of your old one. The installer will ensure that it’s connected to the mains cold water, your other heating source (such as a gas boiler or biomass boiler), immersion heater, temperature sensors and the solar collectors themselves.
6. Next they will install the pumping station, usually near the water tank. The expansion tank will be installed on the solar thermal loop, which is usually nearby. Its job is to prevent pressure changes that could damage the system.
7. You’ll get a heat generation meter which must be MCS-certified if you want to take advantage of the RHI, and any control equipment that comes with the system will be installed.
8. The installers will then bring the system to pressure by pumping the heat transfer liquid into the system up to a pressure of around 2 bar.
9. Finally, your MCS-registered installer will register your solar thermal system so you can apply for RHI payments of up to £525 per year.
So that’s the process of installing solar thermal panels. Remember – it's always best to use a professional to install any kind of renewable technology.

Are you currently weighting the possibilities of adding a solar system to your commercial building? With lots of commercial property owners in the UK using solar now, many more are gradually coming to terms with the numerous benefits they stand to derive by getting one. Therefore, if you’re thinking about adding the system to your commercial building but do not know where to start, you’ve come to the right place.

In this post, our aim is to help you calculate the number of solar panels you’ll need to power your entire commercial building. Starting from the panels, you can begin by taking into account everything that makes use of power in your commercial building to get a good idea of how many you’ll need.

• To get started, you’ll have to determine the number of watts used by your commercial building. To get this, you simply have to go through your utility bill for kilowatt-hours (kWh). This varies amongst buildings and being able to identify your daily average energy usage will assist you in getting your solar panel needs.
• Once done, you’ll also have to determine the peak sunlight hours - having in mind that the solar panels only work when under direct sunlight. Once determined, you can then multiply the figure in hours by your home’s hourly energy usage and divide by your selected solar panel’s wattage.

In general, a medium-sized commercial building making use of an average amount of electricity will require about 70 average quality solar panels so as to cover its entire electricity needs. These are, however, just averages, so yours could be more or less so getting the idea is vital here.

How Do Solar Panels And Batteries Work Together?

With solar panel system rapidly becoming an ubiquitous phenomenon within the modern society, several homeowners in the UK are just coming to terms with the numerous benefits offered by the system. The solar power’s popularity has even led to the rise of another renewable technology - solar batteries able to store excess solar power that can be used later. Now several companies such as Tesla are now building solar batteries that can be fitted alongside solar panels for your building. So how exactly do solar panels and batteries work together? Let’s have a look!

Solar panels make use of the sun light to generate electricity and as a result, they can’t function when sunlight is absent - giving a big issue of how to power your house when it’s dark. In the event whereby this occurs, you’re afforded two options which is either to contact energy providers to buy electricity or purchase a battery storage system.

So what’s the function of the battery storage system? Basically when your solar panel provides electricity which is not needed right away, a solar battery will work to convert the DC electricity into AC energy which is going to be stored for later use (when you actually need it). in other words, your solar panels charge the batteries when you do not require the energy they’re generating right away.

As a result, when it’s dark and the solar panels are no longer functioning, your system will tap into the energy that’s already been stored by your battery for later use. This way, you can be totally independent of the National Grid, which implies more savings on your electricity bills.

In a similar way to other major home improvement projects, some specific requirements must be met to allow for the installation of solar panels. The main reason why these standards and regulations were established is to minimize the risk of the solar system becoming an issue or potential hazard in the unforeseeable future. So if you’re thinking about buying and fitting new solar panels, you’ll probably want to know whether or not you’ll require to submit a planning permission application for approval before you can proceed.

Generally, solar panels are covered under what’s called “Permitted Development” which gives you the freedom to install your solar panels without having to apply for a planning permission. However, there are some exceptions to this rule. These exceptions include if your house is a listed building or if your house is located within a conservation area. In these exceptional cases, it’s possible that you’ll need to apply for a planning permission, but this will largely depend on the discretion of your Local Planning Authority. What’s more? Solar panels are usually subjected to normal building regulations which includes examining the roof to make sure that it can support the additional weight. You can call in a MCS certified installer to carry out this check for you.

In order to install your solar PV on your roof, you must follow these guidelines:

✓ Your solar panels shouldn’t go beyond the highest point of the roof (excluding chimneys).

✓ The solar panels shouldn’t project beyond 200mm off the roof’s edge.

✓ The solar panels should be removed once they’re no longer used to produce electricity

✓ The solar panels should be installed such that the area and building’s appearance change is minimized.

When you’re about to transform from the standard electricity to solar energy, what determines your solar system’s size is the amount of solar that’s required. The amount of solar that you’ll need, on the other hand, requires considering the end goal, be it to increase money savings, reduce environmental contamination, maximize Returns On Investment ( ROI), or just to copy what the neighbour’s done.

In order the determine the number of solar panels that is needed, the first step would be to calculate the number of kWhs that’s currently being used. A kWh is what’s used to determine the amount of energy that has been incorporated over time which the utility uses to bill you. What’s strongly recommended to create a suitable range is a 6 to 12 months average of your household electricity bill. Other factors that can play a key role in the determination of the number of solar panel needed include the following:

✓ Sunlight exposure hours. In order to know just how much energy your solar panels will generate, there’s a need to know the number of direct sunlight hours you should expect on a daily basis. For example if you stay in a region that’s usually very sunny, then it’ll be reasonable to expect more energy production per panel than regions that are usually cloudy.

✓ Angle and size of the roof. Roofs with a lot of workable space may require to let go of some efficiency opting for larger and cost effective panels to achieve the targeted energy. However not all homeowners have sufficient roof space or shade coverage for the solar panel they actually want. Also, the degree at which the roof slants will also determine if the sunlight is hitting the panels well enough and the amount of energy that can be generated thereof.

Most people want to connect solar panels to a battery when they’re not at home all day to use the electricity they generate, or generate more than they consume over a day. Solar batteries are a great way to maximise the savings on your energy bills since you can use every unit of electricity you generate.

If you want to connect your solar panels to a battery, the best – and safest – way is to ask an MCS-registered company to do it for you. They’ve had lots of training and hold qualifications in handling electricity and installing solar batteries, so they will be able to recommend the best battery for your solar panels and for the among of electricity you use. Some of the brands they might recommend include Tesla, SolarEdge and SolaX, but there are many more to choose from. If you want to send electricity to the grid from your battery to receive Smart Export Guarantee (SEG) payments, it’s also worth leaving installation up to a registered installer. This is because you might not be eligible for payments if your battery wasn’t installed by an MCS-registered company.

However, if you do want to have a go at connecting your solar panels to a battery, it’s worth finding out whether your system is ‘storage ready’. Most relatively new systems will be, since batteries are becoming more commonplace. If your solar panels are storage ready, they will have an inverter that can easily have a battery added to it. If this is the case, then you should be able to buy the solar battery you want and follow the manufacturer's instructions to install it.

But it’s worth remembering that electricity is extremely dangerous when handled improperly. If you don’t get the solar battery connected properly and something goes wrong, it could cause a fire or you could electrocute yourself. If a fire breaks out due to your battery, it’s unlikely that your home insurance company would pay out since you connected the battery yourself. That’s why it’s always worth speaking to a registered installer to install a solar battery storage system for you.